Новини
Erwin v
търси този кит
търси този кит
Mitsubishi A6M2 Zero Fighter (Zeke) w/4x4 Light Vehicle Type 95 Kurogane & Maintenance Crew
Tamiya 1:48
89757 2008 Нови части Multi topic (3)7 October, 05:47
Erwin v
търси този кит
търси този кит
Mitsubishi A6M5c Zero Fighter (Zeke) w/4x4 Light Vehicle Type 95 Kurogane & Maintenance Crew
Tamiya 1:48
89760 2008 Нови части Multi topic (3)7 October, 05:47
Erwin v
търси този кит
търси този кит
Japanese Military Aircraft set w/4x4 Type 95 Kurogane & Maintenance Crew
Tamiya 1:48
89761 2008 Нова кутия Multi topic (6)7 October, 05:47
Marcelo Freitas
маркира кита като поръчан
маркира кита като поръчан
F-35 65th Aggressor Squadron Camo Paint Masks Set For F-35A by Italeri, Tamiya, PM Model, Revell
DN Models 1:72
72/827-047 2022 Нова матрица 7 October, 05:47
Erwin v
търси този кит
търси този кит
U.S. Navy Aircraft Set No. 1 2 F-14 Tomcat, 2 F-18A Hornet, 2 S-3A Viking, 2 A-6E Intruder, 2 A-7E Corsair II
Tamiya 1:350
78006 (7306) 1985 Нова матрица Multi topic (5)7 October, 05:45
Chris Reimann
добави нов фотоалбум.
добави нов фотоалбум.
5 6 October, 19:25
Marcin Dudek
добави нов фотоалбум.
добави нов фотоалбум.
13 15 September, 15:32
Marcin Dudek
A new build starte 🙂. It seems quite easy but one thing puzzles me - the tracks. They compose of 4 straight plastic parts and instruction says to bend them with hair dryer. It is first time I encountered this type of tracks. Anyone tried doing something like this?
A new build starte 🙂. It seems quite easy but one thing puzzles me - the tracks. They compose of 4 straight plastic parts and instruction says to bend them with hair dryer. It is first time I encountered this type of tracks. Anyone tried doing something like this?
15 September, 15:36
Snake Plissken
I have heard of this type of assembly but have never built one. However, I have lots of experience heating and softening styrene plastic. You can also try very hot or boiling water -- soak the tracks in boiling water, then fish them out of the water with long tweezers and bend them around the rear sprocket, idler and road wheels and hold until they cool. You may even get by using no heat, just slowly and carefully bend curves into the tracks.
I have heard of this type of assembly but have never built one. However, I have lots of experience heating and softening styrene plastic. You can also try very hot or boiling water -- soak the tracks in boiling water, then fish them out of the water with long tweezers and bend them around the rear sprocket, idler and road wheels and hold until they cool. You may even get by using no heat, just slowly and carefully bend curves into the tracks.
15 September, 20:46
Marcin Dudek
After some work done I need to say I am a little disappointed with this kit. Instruction includes some mistakes and it is not always easy to read how and where exactly a specific part should be located. More over I expected more from new molds (parts require a lot of work to remove additional plastic).
After some work done I need to say I am a little disappointed with this kit. Instruction includes some mistakes and it is not always easy to read how and where exactly a specific part should be located. More over I expected more from new molds (parts require a lot of work to remove additional plastic).
22 September, 13:17
Snake Plissken
Hi Marcin. My advice is to *expect mistakes* and do your research accordingly. It may or may not be fun to research the T-55 but most of the photos or line drawings you can find online are free, it just takes some time.
Hi Marcin. My advice is to *expect mistakes* and do your research accordingly. It may or may not be fun to research the T-55 but most of the photos or line drawings you can find online are free, it just takes some time.
25 September, 04:46
Snake Plissken
Good job adding the injector lines on the engine. I overlooked it the first time. 👍
Good job adding the injector lines on the engine. I overlooked it the first time. 👍
1 October, 05:53
Marcin Dudek
Thanks Snake 🙂. I was considering adding some more parts to the engine but they wouldn't be visible after assembly so I left it as it is. Thanks one again for the track bending tips, they were very helpfull.
Thanks Snake 🙂. I was considering adding some more parts to the engine but they wouldn't be visible after assembly so I left it as it is. Thanks one again for the track bending tips, they were very helpfull.
1 October, 15:48
Marcin Dudek
Some job with wearhering done. Still, I forgot to apply the decals first 🤦
Some job with wearhering done. Still, I forgot to apply the decals first 🤦
7 October, 05:41
/bg/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=bg
35
35
/bg/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo