Новини

Never a Pro
interesting approach.

Mr D
Very nice, nice paint on the exhaust, what paint did you use on the airfame.??
What decals are you going for.
Like it 😁👍

Thomas Wirsching
Thank you. The exhaust was painted with Alclad Exhaust manifold color. It matches spot on. The Airframe was painted with Alclad High shine silver and Gunze Khaki green. The struts were painted in vallejo straight black.. I will "steal" the Latvian markings from Eduard`s Limited Edition Gloster Gladiator set as I will use special Lithuanian markings for that bird later😁

J35J
Lovely build and paintjob!👍🏻

Thomas Wirsching
Finished my Latvian Bulldog today. The SBS rigging wires are very nice but careful work and a steady hand is necessary here. Now its time for the pilot and a small diobase. At the few pictures I have about the latvian Bulldogs they all thave their upper and lower right sided national emblems unevenly displaced to the inner wing . This looked very dorky to me and I took the artistic licence and placed them symmectrically which looks much more aestetical to me.

Neuling
Excellent.

Mr D
Brilliant 👍👍 excellent job👌 nice engine design in this aircraft rigging looks really good..😁👍

Thomas Wirsching
Gentlemen I call this build finished. It was a very pleasant and relaxing build. Thanks for watching ☺️🖐

David Taylor
Brill.

Felix
Wow, so schön! Wie ist der Bausatz?

Guy Rump
Lovely job! 👍

James Richards
Thanks Guy!

Doubtingmango
So I just finished this little Italian job. The decals came out with a lot of the edges showing, which then got a lot worse when I added some washes. I used Microset on the decals, and then sealed them with Tamiya semi-gloss before the washes, but it actually looks like the washes got under the decals. Any thoughts?

Bogicevic Vladimir
It looks like you haven't spray gloss coat before you applied decals. Or decals didn't set well. There are two solutions. One is lacquer thinner. Put the thinner with fine brush in dots over the place where you have silvering. Thinner should destroy the film. If it raises paint under, just leave it, it will settle back. Important thing here is that, once you applied thinner, you shouldn't touch decal for something like 20 minutes, at least. Second way is mix of sugar and water, half - half. You make a hole with a needle on the decal, than you put mix on the top. It should enter in the space between decal and paint and, when drayed, make a gloss film in between them which will act as a gloss under the decal. Wipe excess mix with wet cloath and you are done.

Mr James
How annoying. I've never heard of the sugar water trick from Bogicevic. I'll be interested if this works. If the thinner, sugar trick fails, what else can you do but use a scalpel to cut around them, since you've sealed it,

Mr James
Oh, nice paintjob by the way

Doubtingmango
Thanks mates! I believe Bogicevic is right. I think I did fail to gloss coat before the decals. I think I'll try the sugar water first

Bogicevic Vladimir
Ok. There are few small tings I should add then. Heat the water first, when hot it will disolve sugar beter and apply it while it's still warm, it will have more viscosity. Make small hole or slice with modeling knife, put few drops of mix on the top and let it dry. You will see emidiatly if it's penatrating. When dry, wipe carefully excess mix with moist cloth. Repeat where neaded. I know it sounds ridiculous, but it worked for me many times.

Doubtingmango
Thanks Bogicevic! I'll give it a shot. If it doesn't work I'll try the lacquer thinner technique. I love this site!

Mark Sherwood
Where the *uck's this been hiding. Very nice build Mr Mango and I hope the decal solution from Bogicevic work's out🤞

Doubtingmango
Thanks Mark! So I punched some holes in the decals and applied the warm sugar water, but unfortunately it did not seem to make a noticeable difference. I decided my best shot was to just grab the scalpel and remove the decals, which was very easy. Bogicevic said the solution would get under the decals! I have successfully applied new decals, and my little Italian job is now base-worthy. New pics to come.

Bogicevic Vladimir
Well, you find a solution, which is the most important thing. I can not know why something that worked for me many times does not work for you in this case. Maybe that what I think is silvering is residual glue from decal paper. Who knows... Anyway, good luck with your project.

Doubtingmango
Thanks Bogicevic! You were definitely part of the solution

John
All's well that ends well. 👍 Mango, your builds have me hankering to do some armor but I still have commitments to do a couple more a/c. When I do get a chance, part of me wants to start small with a Pz IV, but another part says go for broke and do a Maus!

gorby
Very nice work!

Neuling
Good result anyway!

Doubtingmango
Thanks guys!

Doubtingmango
As promised, new pics of the new decals have been added, along with pics of the work I have started on the base. Once again, thank you for the help Bogicevic!

John
Really cool base! 👍

Guy Rump
Great result on the tank, the base looks good too. 👍

Doubtingmango
Thanks John and Guy!

Doubtingmango
More work on the base. Just need to paint up the base and add foliage

Doubtingmango
And it's finished

Rui S
Great work allround 👍 Beautiful vignette

Doubtingmango
Thanks Rui! Always appreciate the feedback

Tcamp
Awesome work

Pietro De Angelis
Beautiful work, congrats!

M0rce
That's pretty cool 😎

Tcamp
Texas hurricane is underway let the fun begin!
Sorry for inverted pics cant get rotated🤠

Ben M
Rotation is well hidden. To rotate your photos, open your album. Click on "manage". Then turn on the "advanced options" toggle. You will now have the ability to rotate photos in the album.

Tcamp
Thanks ben
That was driving me nuts!!!!
Appreciate that brother!

Ben M
Glad I could help, mate! Looks like a fun build.

Tcamp
So far so good just a cat 1 now hopefully ill turn her into a cat 5 (LOL)

Tcamp
I reworked the main jib boom
I wasnt feeling the kit one
Its still a work in progress

Doubtingmango
Beautiful work!

Tcamp
Thank yall
Im not a rivet counter or anything but.....
The more i looked at the kit boom i could not figure how it would work ..
Revell had their boom right im also going to support mine as they did and use poles instead of ratlines. Which tie down inside of the work area ?
Im not feeling that one either lol
Again thanks

M0rce
Oooohhh... so nice 🙂
A Lindberg kit? Seen them but never got one, yet. That looks amazing.

Tcamp
Dude you have to get one!!! The gallos and pullies are beautiful and the cabin has seperate doors at least the main mast has the mast lights boom was weird though
Oh its 1/90 a good workable size and the wheelhouse windows are open!!!!!

M0rce
Looks amazing, I'm going on ebay now 😀

Tcamp
Cool
The winches are great the deck rollers and gallows even have that transfer pulley like the artic corsair has.
And the anchor windlass even has a brake just gotta add some brake wheels to the main winch.
Dig this ...ok so revell has a double bit anchor windlass and 2 chains but only one anchor haus on hull.
Well this 1 has a double bit windlass 2 haus on hull 2 anchors but only 1 hole on

Tcamp
On focsal i find that ironic ( lol)