Новини

Ian Doody
Made a start on the 1/32 Trumpeter F4F-4 Wildcat, I'm having my wings permanently folded, this is just all dry fitted so far, I'll add more detail later when the wing is added. No point cleaning up the inside part of the wing of ejection holes, as this will be hidden behind the wing. Think it looks ok so far.

Ian Doody
So today I've semi painted up the other sides wing root fold system. And started dry fitting the engine. Need to pick a scheme from the Techmod decals at some point, thinking of 1 or 4 so far.

Ian Doody
Ooh landing gear and engine support structure. Just needs a few touchups, thats it done for now, have to glue it all up straight away, doing it later would be a pain in the ass. Looks ok, I'm no expert on these things. Just for fun build in-between other stuff.

Ian Doody
I think, as an engine that'll do really, don't need anymore detail on it. Couldn't see it if it was there anyway. I'll paint the rear bank of cylinders, but that's probably it.

Ian Doody
That's all for today, making the most of what you get in the kit, only added bits of wire, no sense going mad with detailing parts you wont see. Prop tomorrow, finish the rear bank of Cylinders, and make a start on the cockpit. Looking nice so far, looks like an engine to me.

Ian Doody
Engine, exhaust manifold system and front bulkhead done. For what you can see, the kit parts are good enough. No point spending lots of money on a resin engine. Just some wire and a bit of paint.

Rui S
Looking special 👍 I'm in 😎

Guy Rump
Looking good and detailed build notes, following. 👍

Ian Doody
That's it for today, don't think I can handle seatbelts as well. So far so good, looks like a cockpit, when it's in the plane, you won't see anything. I tarted up the kit seat, as I couldn't stomach making the PE eduard one.

Rui S
hum, hum 😎 looking good 👍

Rui S
Welcome to scalemates🙂

Rui S
Welcome to scalemates🙂

gorby
Nice work so far. The colour and the flower motif really suit the vehicle.

Rui S
Looking Great, indeed 👍

Martin Oostrom
Gotta love a T2

bughunter
Again a wonderful build of a famous car 👍

Bill Newcomer
I had some adventures in a microbus with some of my cousins back in the early 70's

Martin Oostrom
Now there's a sentence that can be misinterpreted on purpose 🤪

MS K
Woops. Fixed a typo of #15.

Glenn
T2 Judgement Day

Stéphane Jayet
Once again, a fantastic job !

Christian W
This looks pretty good! Nice with all those flowers 🙂

Ben M
Watching...

Doubtingmango
On board

Guy Rump
Me too. 👍

Dennis
What a Beauty 👍👍👍

pitty this Kit is so rare These days...

Marco Gallmann
Looks great 👍

Michael Kohl
Very nice.

Lee Hoe Yen
Thank you.

Christian W
I finally started this thing.

István Szücs
I'm curious for the final result!

Christian W
Me too 😉 I think I'm going on with that hood. The chances to get the right on ist nearly Zero.

Chris Parsons
Aah….been there, done that. I know your pain young Jedi!
I had the original as well at one time, re-powered with a 68 440 six pack, never going back to build another real "muscle car" but nice to have a representation of it at the least.
I converted the AMT 1971 body to a 73/74 body (it's a much cleaner mold) but used parts from Revell/ Monogram B body kits to get there in the end…musta used at least 4 other kits for parts. Scariest part was changing the rear side windows shapes from sweeping up to sweeping down. I may have pictures here somewhere…not sure but, I'm pretty sure I posted the build thread on Britmodeller if your interested

Christian W
@Chris ... That was my first thought when I read the first sentences, where you wrote that you converted the 1971 into that: the small window at the side and the c-post. I'll do a research on britmodeller to see, what you've done. On that point, it is too much work for me to go such a way. I want do have the kit done in December. I know, the details "under the body" could be better, but when it sits in the shelf, it doesn't matter somehow. For my needs, it is ok. It's only the hood, what concerns me for accuracy with the look to the movie car.

Christian W
@Chris ... I found your thread. But sadly there are no pictures anymore.
britmodeller.com/for..ger/#comment-3826045

Chris Parsons
Oh crap!
Sorry

Christian W
No problem 😉

Chris Parsons
I've found and added some images of my finished model here, no longer have images of the w.i.p. No idea what happened to them, you may be able to use (or not) for your build. The images are in my "Albums"

Bill Newcomer
I shall follow too.

Chris Parsons
That's nasty! I've had a paint do that to me as well! Never a good time!

Martin Oostrom
Tough luck Christian.

Bill Newcomer
I have never seen hobby paint crack like that. What is the carrier, enamel, lacquer, water?

Bob Hall
I thought it was cat hair at first glance and I was going to suggest, it time to shave the cat, but I see it's more of a deep rooted issue ! 🤔

Christian W
Thanks for your comments. First when I came into my hobby room I also thought it is a hair but... you see. I don't know, what went wrong. I used my rattle cans as on every model kit I built for years.
@Bill I don't know, what the colors are based on. As soon as I had no issue with them I didn't care.

The Dodge sits in a bath to get the paint of. After 24 hours the black was gone. Usually the primer stays on the body. In this case it was as usual 😄 but the hood is sticky and some parts of the body too. The crap goes on.

In the time of hoping and praying 😄 I took the bumper to get rid of that bumperettes.

Nigel Chapman
Is it a chemical reaction with the different paint colours?
Do you use the same paint manufacturer for your rattle cans?

Christian W
Maybe and no 😉
I do not know, whether it is a chemical reaction or something else. The manufacturer are different. I had the same issue with a
-> black Pontiac (easily 5 years ago - Pontiac Firebird - RIP | Album by Dominik (1:25)),
-> blue F40 (finished in 2017 - 1987 Ferrari F-40, Revell #7327 | Album by christian-w (1:24)) and
-> black Viper (Restoration in 2022). But the cracks came after some months or years and not within 24 hours.
-> KARR after
Now, when I'm writing this lines, I remember, that
-> another Pontiac got cracks in 2022 too (1989 Pontiac Firebird (red) for a friend - wip | Album by christian-w (1:25)).
The filler was the same but the body color was another manufacturer like on the Dodge. But the cracks came after clear cote. So ....

What do they have in common?
Filler? Yes. Only the Viper has old color under the new painting (it was a restoration - paint remover followed by a new paint job)
Color? Different manufacturer
Clear coat? Not all of them. Only KARR, the red Pontiac and F40.
Cracks came between 24 hours (Dodge), 9 months (red Pontiac) a couple years (F40). Also the time between the different layers vary or the question about a wet sanding and painting over it. There are a minimum of 2 days between the steps. Usually weeks, especially with clear coat.

I don't see a clear pattern.

shadowlight
Just some more thoughts about what do they have in common...
- moisture, temperature and air condition in your working room
- air pressure and paint thinner
I am very sorry that this happened to you btw.

Skyhiker
Not sure if this applies but cracks can happen if the under paint drys slower than the top coat. This can sometimes happen when you use a laquer or oil based paint and then add on top a faster drying acrylic or water based top coat that is too thick.

Christian W
Thank you for your suggestions.
@Skyhiker .... I think I can skip this reason mostly because. There were 9 days between base coat and the black. Before I painted it black, I wet sanded it and let it sit 2 days for drying. I think, that was enough time.
@shadowlight .... moisture and temperature could be a reason. Because I used my rattle cans for painting, I was outside. In this case in the evening hours and not middays. The day was sunny itself but when I painted it, the sun was nearly gone. Thanks! I'll keep that in mind.

Another little step done: removing the bumperetts.

Christian W
At the weekend I sanded a lot of the filler down. The surface should be smooth enough. Yesterday I did another try to get it black. This time I used ma airbrush to paint it. And I skipped another layer of base coat 😄 At this time I don't care. I just want to have the paintjob done.

Bozzer
Christian, I don't care what anyone says, picture 20 looks awesome, and I would've just rolled with that, and stuck it in a diorama of a kid, trying to fix it up. I doubt that I'd ever be able to get that look, and you nailed it by accident! I gotta admit though, that black looks nice 👍

Christian W
You've nailed it. That were my thoughts too. If the next try fails, then I'll go with a restoration project. I'm not a person who throws model kits into the trash.
Thank you for your lines.

Nigel Chapman
Christian, Your perseverance has paid off handsomely, that new paint job looks ace

Christian W
Thank you. Yesterday I took it but I didn't do anything with it. I'll go for another wetsanding job. Why? Hm. Stupidity is sometines an a-hole. When I brushed the underside of the hood, it went off of the "holder", flipped and landed with the freshly painted side on the ground of my paint booth. You can imagine, that tehre is still some dirt on the ground. So that dirt is now on the hood scoop. Lesson learned: keep the parts better on the "holder".
I guess, that I have to give it another layer of black before even thinking about doing the clear cote.

Patryk S.
Following! Good luck!

J35J
Taking a chair!👍🏻

Łukasz Gliński
Me 3, I have to see that! Still procrastinating mine 😄
Thomas, are you considering getting rid of the decal with my support perhaps? 😉

Thomas Kolb
Łukasz, I am not going to use the provided decal sheet, so if you want it, just PM me with your address and I can post it.

Thomas Kolb
(And for everybody else with knowledge about the different versions of the Yak-12, yes, I am aware of the differences between the A-version in the kit and the R-version used by the Hungarian People's Army. But since I am not able to scratch build the entire wing and empennage structure, let's just call it artistic license.)

Cuajete
Looking good so far, Thomas 👍
Feel free to take artistic license 😉

Robert Podkoński
Watching for sure!

Alec K
Taking a seat, looks great 👍

Thomas Kolb
Thank you very much, dear gentlemen for your attention and encouraging words!

Michael Kohl
Following too

Nicolas
I'm joining in as well. Great build so far. 👍

Bruce Huxtable
Admiring your skills, and learning from your problem-solving, Thomas. Transforming an A-Model kit adds to the challenges 😉

Thomas Kolb
Thank you Michael, Nicolas & Bruce for your interest and compliments! This kit is actually not quite as bad as some other Amodel kits I have built - the designers have created some pretty nifty solutions here! If anything, it is a bit unforgiving - make one small mistake and you can be sure that it will keep coming back to kick you.

Łukasz Gliński
What a cool visor 👍

Cuajete
Great progress! 👍

Bernhard Pethe
Wunderbarer Modellbau. Ich hab das Modell auch noch liegen und genauso wollte ich es auch machen. Mal sehen, wenn ich groß bin. 😉

Thomas Kolb
Bernhard, danke schön! 🙂 Ja, es ist ein ziemlich kniffliges Modell, aber es macht großen Spaß, es zu bauen!

Cuajete
Looks great so far, Thomas 👍

Nicolas
Yes Thomas, I don't think you get any easy builds from Amodel. But with some work you get a nice and rare model. I realy like your progress. 👍

Thomas Kolb
Bruce, Lukasz, Cuajete, Nicolas, thank you! Yes, Amodel is actually cool in that they take a chance to make models outside the ordinary. Who else would design a model kit of a strange and ugly little high-winged Soviet aircraft instead of another Stuka, Tomcat or a Spitfire?

Danumurthi Mahendra
Lovely topic that I dont see alot. Nice progress!

Roland Sachsenhofer
Wow, what a beautiful an clean build! Inspiring and masterly!

Cuajete
That Alclad gloss coated looks great with the brush, Thomas 👍

Thomas Kolb
Roland thank you mate! Cuajete, yes, this is the best gloss coat I have ever tried. It levels out to an absolute mirror shine (at least if it is applied to a perfectly smooth paint layer). This model ended up with a bit of orange peel effect at some places, so it is not absolutely perfect, but I can get away with it.

Guy Rump
Looking great, following. 👍

Juergen Klinglhuber
Great result Thomas - 👍

Thomas Kolb
Hereby I declare the project finished! Quite a fast progress for me, only three weeks from start to finish. It may not be the best model I have ever built - there are too many silly or clumsy mistakes here and there - but it was great fun! More photos will come!

Łukasz Gliński
That escalated quickly and nicely 👍
Where did you get the snow from in August? I know it's up north, but still... 😉

Roland Sachsenhofer
Wonderful and inspiring! Great work!!

Neuling
Top result! Beautiful photos!

Robert Podkoński
Great job, Thomas! Fantastic photos.

Alec K
Well done Thomas 👍

DuperScale
Lovely result, very clean build. 👍

Guy Rump
Great result, congrats! 👍

Nicolas
A lovely little bird. 👍

Ekki
Excellent work!

Curatorm
Exquisite model! Very good work.

S M
The short-run-kit looks really difficult to work with, but you have mastered it. Top model!