Новини
H Katoдобави нов фотоалбум.
11 8 December, 14:00
Landlubber MikeMy dad had a Challenger when I was little in blue. Looking forward to following along on this one - I might have to build one to relive my childhood!
1 9 December, 16:36
thetaThis is a nice model, good level of details, no fit issues. Only thing to note is if you want the bed be movable, do NOT glue F12. The instruction does not specify this. Other than that, this is a very enjoyable build.
17 December, 05:42
Martin Oostromдобави нов фотоалбум.
10 6 October, 16:08
bughunterThat is the first model (great one BTW) here, where we see after a WIP a WIL album 👍
6 October, 17:50
Jennifer FranklinThis is a great subject. I love the old VWs, and you've done it justice; it's very nice.
17 December, 05:06
Mr Dдобави нов фотоалбум.
56 снимки
Beriev Be-6 flying boat/ By Playfix -Veb -Plasticart & Revell 1:72
1:72
The trim tabs, door handles, painted,
It's finally ready for a clear coat prior to decals.
I have seen people getting ...
57 24 July, 16:32
Mr DThanks for the likes 😁👍 it's interesting to see how a 33 year old kit builds up ??
1 August, 15:31
Edouard CarrGreat idea about the watch pins! ⌚ Definitely gonna try this out on my builds. Looking forward to the finished result.
1 September, 08:43
Mr DHi Edouard👋😀👍.
Yes l just get cheap ones of eBay, the do different sizes, you can pull ends n spring out for barrel look, or file ends last to have a recoil cannon look.
The gun turret nearly there now....lots of sanding n filling low spot.
Thanks for looking in on build.👍👍
1 September, 13:24
Zbynek HonzikI'm very curious to see the result. I built this model as a young boy too.
4 September, 20:22
Mr DHi Zbynek 👋🙂👍.
Thanks for your interest. Nice to know you had it too, l built X3 the Tu airliner and the bomber. But this was my favourite as l liked the shape and that it had floats n guns.
Got part of tail on this evening.
Keep looking in for updates 😃👍👍
4 September, 20:57
Mr DGood to have you along Guy 👋😃.
Bit of fine sanding n tidying to do next then look at getting an engine effect in cowling area.
I replaced side vent for smaller one now, checked photos... and l made it way to big.
Catch you on the next steps.
7 September, 20:15
Edouard CarrHey Mr D whats the Gorilla Glue like? Is it a clear PVA or a resin Super Glue Type? Do you use it just for clear bits or as n all purpose? Thanks in advance E.
12 September, 21:46
Mr DHi, it dries 100% clear but is slow.. to air dry ..so leave overnight.
But it's worth it as very strong. And is very neutral on paint and clear parts.
It's almost like an air drying epoxy, not harsh like super glue or poli ...very safe.
I only use it on clear stuff as it's stronger than PVA but not good for general building.. l do use it to fill gaps sometimes.
👍
13 September, 10:34
Mike MontgomeryDon't think I'd trust those decals. The red stars are easy enough to replace or paint on, the bort numbers might be more of a challenge.
13 September, 12:47
Mr DHi Edouard 👋..yes 🤣 lm on 12 model with it and never had anything come loose.
Mike👋.... No mention neither! I've purchased some more Soviet stars now, may have some numbers leftover from others project's.
Gorby, Thanks buddy 👍
13 September, 15:53
Christian WThis is a quite interessting plane you're building! I like the shape of the wings. Pretty good build and pictures.
18 September, 04:57
Mr D@ Christian W.
Thanks buddy 🙂👍
Yes it a bit different, yes has nice gull-wings.
It's a trip down memory lane for me... I slapped one together back in 1991 as a kid.
Thanks for the interest.... I like seeing people's build processes n history....so doing the same.👍👍
18 September, 16:41
Zbynek HonzikI'm anxiously waiting at the monitor for the paint job! Fingers crossed!
18 September, 19:04
Christian WMr D ... 🙂 I like too to see, how much progress my skills during the last 10 years did. Good for me is, that I own most of my model kits since I was a kid. My first plane, car and truck are still in my shelf or boxes.
Because I stumbled somehow over your wip, I checked the history of the kit. It is rally unbelievble, that those engine openings are on the bottom of the motors. Amazing. I wouldn't notice that without your hint.
19 September, 04:25
Lorraine LinCannot wait to see the result. Your work reminds me of my first kit, it was a Victor bomber by Matchbox (They had a JV factory in Shanghai at that time). But hard find it in the market now.
21 September, 11:33
Mr DHi Lorraine 👋.
Glad your interested 👍 there are X2 colour schemes for the be-6 the Soviet green or the Chinese blue, l liked the blue version but could only find suitable replacement decals for Soviet.
My first kit was the Matchbox Electric lightning,.... Built it with my dad....was nice as was 3 colour plastic out the box.
The first models l built on my own were the Veb/Playfix be-6, & Tu- bomber, so nice to revisit.
Got X2 models at min I'm preparing for paint.
Yours is coming along well...."carefully work" 👍👍
21 September, 15:00
Mr DThanks Skyhiker 👍
I usually use Velejo or AK acrylic, but I'm going to use Tamiya on this one as it won't fit in cabinet.....and l find Tamiya acrylic is a tough paint better for wear n tear, as I'm sure it's going to need dusting now n then 🙄🤣.
The Tamiya paint turns out to be darker than advertised on the lid n chart, I've ordered a white n thinner to Tone down.
Like you I've had 2x build going on.
The Fw-190 really pop's once decals are on..... Remember the trim tabs are red....l just had paint.
😁👍
12 October, 21:34
MarkoAs a child, I once built the kit with my father.
Very simple kit of its time. But the shapes and proportions are convincing and you really did a fantastic job with it. I'm looking forward to the finished model.👍
5 November, 21:40
Mr DHi Marko👋
Nice to hear you have good memories too, first kit l built with my Dad was the Matchbox Electric lightning, it was good as had 3 colours... think my dad painted few bits silver too.
the Veb Playfix kits l would buy on Saturday morning with pocket money it came with strange pot glue.
I built 3 or 4 definitely built the Bear soviet bomber...l can remember.
Funny you commented on this tonight......as l was just checking it over ready for paint in next few days. I've just been wrapping up my IAR-80 project.
😁👍 Stay tuned
5 November, 22:19
WeizenbrotWow, it would be very excited to see the finished model.Very detailed research and nice details. I visited an aviation museum in Beijing few months ago and saw this aircraft. A beautiful flying boat indeed.
8 November, 15:10
Mr DHi Weizenbrot 👋
Yes it looks nice with it's gull shape wing, ione of its rolls was to search n destroy trespassing submarines with it's depth charges .
Think the Chinese one is Blue colour??
Thanks for interest 👍
8 November, 16:44
TrezDid you finish it? I just necro-surfed the whole build only to be unceremoniously dumped back at phot number 1 lol
10 November, 02:20
Mr DHi Trez, l have recently painted the bottom colour, l will be painting the rest this week, lve had few other projects on the go... Won't be long.
😀👍
10 November, 16:02
WeizenbrotHi Mr D. Yes they are light-blue for belly like the Soviet ones and dark blue for the rest part. Some of them have even been modified with turbo-porp engines.
11 November, 02:22
Mr DHi Dave 👋 thanks 👍
Been working on this long time now between other projects... try n push to get her done now.
1 26 November, 20:09
Bernhard PetheEs freut mich sehr, wenn da jemand ist, der noch so alte Plasticart Modelle zusammenbaut und sich dabei richtig Mühe gibt.
Ein Teil, was ich in meiner Jugend mehrmals gebaut habe, nur leider habe ich keins mehr davon.
Ich schaue hier weiter gerne zu. 🙂
27 November, 16:31
Mr DHallo,
Es freut mich wirklich, dass es dir gefällt und ich habe auch schöne Erinnerungen daran.
Ich habe auch den sowjetischen Bomber Bear gebaut, also werde ich mir diesen eines Tages zulegen müssen.
Danke für den netten Kommentar Bernhard 😃👍
27 November, 18:09
Ben MLet p equal the number of tubes of perfect plastic putty used.
And let t equal the number of rolls of tamiya tape used.
Then let f represent fun: f = p * t
1 5 December, 13:55
Mr DHi Gorby 👋 Ben 🤣🤣
Not kidding 😲 l need to re stock soon, un-masking was a marathon 😄.
I painted a thin coat of pink primer on the trim tabs tonight.... hopefully not need so many red coats to bring colour up.??
I have enjoyed the process on this one... nice now I'm getting towards the end a bit now.
Thanks for your interest 👍👍
5 December, 19:27
Denis DogadovBe-12 is not a modification of Be-6, do not mislead those who are not familiar with the topic. These are completely different planes.
The evil irony of the Russian army and navy in 96 is also unnecessary.
I can also make fun of Britain's modern army and navy.
The color from the bottom is not the same.
Photos of the Be-12 cabin can be found without problems.
myskillsconnect.com/..-vnutri-24-foto.html
15 December, 14:41
Desert Marlinдобави нов фотоалбум.
36 23 November, 00:44
The BlytonianNice. Enjoying the build?
Someday, fingers crossed. On my opportunity buy watchlist.
1 23 November, 00:53
Desert MarlinYes! It's a great kit. I got one of the special edition with the white metal German Shepherd and the Ernst Rüdel figure. The combinations of parts between Jg 1 and Jg 2 are something to be mindful of however. There are several decals for the car parts so I'm still sorting through that. Time and care must be taken on the cockpit and the figures as there is a lot of posing and seating to be performed before everything is painted. And I am coming back to this one after having started it almost 15 years ago...
23 November, 04:58
Desert MarlinThanks! Picture 5 is wet decal on gloss coated panel. Then two days of working the decal with Mr. Decal Setter and Solvaset. Then gloss coated panel and decal. Then Alclad semi-matte finish. Also used some Tamiya panel line accent between instrument bezels. Then each instrument is given a glass lens using Micro Krystal Klear. Not perfect, but in a dark cockpit it seems okay. The real color and detail will come from the pilot and gunner/radio operator figures…
29 November, 04:32
Rui SI'm not an expert or a spoiler, but I think the 'Kanonenvogel' apeared long after that 🤔
The G1, Specialized tank destroyer evolved in 1942-43.
Basically a conversion of the Ju 87D-3 with attachment points to carry two 37 mm Flak 18 (BK 3,7) cannon in streamlined fairings outboard of the main undercarriage legs. (Cannon attachment points could be exchanged for bomb racks.) Standard defensive armament; often had improved ground vision panel in the cockpit floor.
1 2 December, 13:53
Desert MarlinYou are probably right. I am just building the version I was provided by Hasegawa, which over the years, have not always been accurate! In any event, I find the story (800 takes destroyed) and the era, Kursk 1941/42 to be interesting for sure. This particular Jg 2 scheme smacks of a summer deployment without the eventual knowledge that the impending winter would bring!
2 December, 22:31
Rui SBattle of Kursk. Summer of 1943, from 5 July 😄
The Gunner looks great. Well done 👍
1 2 December, 22:53
Desert MarlinTrue about Kursk. I had worked from the Barbarossa reference which was probably too early for the Ju-87G for sure. Thanks for the compliment! The Hasegawa figures are definitely not 3D printed! Lots of carving to get them in better shape...
3 December, 15:20
Mr DAlways stellar work... Nice to see WW2 subject from you now....... good luck with the build 👍👍
1 8 December, 20:21
Desert MarlinThanks Mr. D. The decals for the inside of the canopies seems to be a little too much work when I can mask the interior and paint the correct color...
1 8 December, 23:22
Desert MarlinSo, the Pilot's hood is really not good. I suppose the middle hood could be too short, but the Pilot's hood is also too tall. About 1 mm too tall. So, if I shave down the bottom of the pilot's hood, I wonder if it will better fill the gap between the back of the Pilot's hood and the middle hood? It seems the gunner's hood fits pretty good.
1 9 December, 03:29
Desert MarlinWell, the canopies have taken days longer than I anticipated. I am almost done with the last (gunner's) canopy. Clearly from the complexity of the gunner's canopy, he had a pretty unenviable job. It looks like the limit bar inside the gunner's canopy, which limits the swing of the guns to prevent damage to the airframe, also limits the visibility of the gunner too!
1 12 December, 16:08
Mr DThe canopy is clear ...you should have a good view of pilot , nice job on crew👍
What have you used to mask the front canopy? or is it just protection?
Coming along nicely 👌👍
1 12 December, 19:44
Desert MarlinMasking has been a combination of 3M Scotch Transparent tape and Tamiya Masking Tape. A little bit of Mr. Masking Sol R and Micro Mask. Just really trying to keep the interior of the canopies very clear for now. The Gunner's Hood is really a ton of work. The interior frame is done except for a little cleanup after the exterior is painted...
12 December, 20:28
Mr DBe worth it in the end ... Looking good, thanks for scotch tape tip .
Good luck with everything 👍👍
2 12 December, 23:30
Erik LeijdensExcellent work so far! The figures are very well done, the clear parts are really clear!
2 15 December, 10:01
Desert MarlinI think I'll let the paint dry for a while and work on the Pak 18 cannons…
16 December, 02:44
bughunterWise decision to let the paint dry. Patience at the right moments saves reworking later 😉
Looks good, do you used enamels?
1 16 December, 18:37
Desert MarlinI have saved my Model Master RLM74, 75, and 76 for just this time! I used Mr.Color Yellow for the stripe and bottom of the wing tips! The Testirs thinner is no good for these paints since it was sold to a different manufacturer and is now unable to properly thin the MM paints. Fortunately, the Squadron enamel thinner seems to be an excellent substitute! Base was Mr. Surfacer 1500 black and grey.
1 16 December, 18:43
Mr DThat Tamiya Saw looks like a bit of kit worth getting 🤔.
The Dog will be a nice touch .... Natzi's liked an angry dog 🐕.
Was Ju-87 used for a defensive role??
Enjoy following your builds 👍👍
1 16 December, 19:02
Desert MarlinThanks all for the comments! Mr. D, the Kannonenvögel was used as a Tank Buster on the Eastern Front.
16 December, 19:14
GUILLAUME Cдобави нов фотоалбум.
34 22 September, 19:41
GUILLAUME CHi, Thanks. Mainly OOB, with some improvements, like on the engine where rods where missing.
30 September, 07:08
Michael KohlAnxious to see how you replicate the metal structure at the cowling.
1 11 October, 16:21
GUILLAUME CI will left this uniform, to hard to have te same result as real at this scale.
I've tried before, on spare part, with 2 metal colors and even if I use my 0.2mm airbrush, the result is awfull
11 October, 17:29
Michael KohlIt certainly does. Not easy by any means and much better than the preliminary tests I did so far.
1 13 October, 16:39
GUILLAUME CFor you attention, I use Vallejo duralumin for base coat, then, dark alu with a thin brush, I use only the tip to have the finest line I should, and draw random line with.
13 October, 17:20
Jennifer Franklinдобави нов фотоалбум.
5 14 December, 18:27
Mr DNice project 👍👍
Good luck with it, what is the part count on this one ?
Like that they gave some track included 👍
16 December, 17:35
Jennifer FranklinWelcome, Villiers de Vos, Michael, Nicolas, and Mr D! The part count is slightly over 80. Compared to the Memphis Belle, a level 5 model, this is a level 3. I plan to focus on technique with this one, which will be the real challenge after the B-17.
16 December, 17:47
Martin OostromBe careful with all the thin parts around the wheels. They are fragile and need to be installed in the right sequence. It is easy to take a wrong turn there.
2 16 December, 18:16
Dave Pluthдобави нов фотоалбум.
6 снимки
Ki-84 S17 - Model
1:48
Well it has been a minute since I really built a 48th scale aircraft. I am going to have to figure out how to fill gaps...
1 17 December, 03:06
NLAWScametovisitдобави нов фотоалбум.
32 16 July, 13:41
NLAWScametovisitSorry about the slow rate of updates everyone. I hurt my back at the gym so I'm having to avoid being hunched over at the modeling bench this week.
19 July, 14:02
NLAWScametovisitOK! Back at it with the interior. This kit is definitely a jump in difficulty from the last one. PE is definitely difficult, and if you're doing this kit, make sure you frequently fit check the flight seats and how they'll mount to the bulkheads!
7 August, 15:57
NLAWScametovisitAAAAAND I hurt my back again pushing too hard at physical therapy. :/ more delays
22 August, 19:14
NLAWScametovisitthe detailing on this kit is really lovely, but the fitting of the parts is really bad. And advice on fixing the massive panel gaps in pic 43 to 47 is appreciated.
3 September, 22:27
MoritzIs the top portion already glued on? If not, try adding some bracing with some cut sprues to force the sides apart. Right about where the kink/end of the doghouse is.
Is the aft bulkhead of the crew cabin causing the problem? If that is glued to both sides, forcing the sides apart may not work.
5 September, 04:03
NLAWScametovisitVery good advice. Had to pry it apart but addint braces definitely helped!
5 September, 18:58
Anatolii SmyshliaievIf still relevant.
Pic 43-45. Before gluing the fuselage roof to the lower part, I glued 2 spacers from sprue scraps between the walls.
Pic 46 and 47.
I simply cut off the inner side of the hood wall, leaving the outer side untouched, achieving a tight fit along the outer surface. And I puttyed a little bit on the front of the hood.
24 September, 08:14
Paulo Fonsecaдобави нов фотоалбум.
13 26 June, 23:56
Peter Hardyдобави нов фотоалбум.
36 снимки
Jon’s GTR XU-1
1:24
As they say, getting down to tin tacks now! This kit you will have noticed is very different. It’s by DDA, an Australian...
Проект: Holden Torana LJ GTR XU1
24 4 December, 04:16
BozzerIt's all in the prep work, Peter!
I'm curious to know though, will the black, also accentuate the panel lines?
For example, the doors, hood and trunk, gaps? Or, would you tackle that later down the line? Or even just leave it as is, and let the natural light, do its magic?
4 December, 05:36
Peter HardyPrep prep and more prep! The black under the doors and bumpers is standard as is the blackouts on the r-send and grille. I want to give this to Jon on New Years Eve so I have a deadline!
4 December, 06:19
BozzerMate, recently I've done more rubbing, than Aladdin's girlfriend!
Large resin models, and OCD, definitely don't come hand in hand!
I have to stop, put it down, and do something else, just for my own sanity?
In the UK, we used to use a black paint, on the sills, called Tetrosyl. It was bitumen based, and prevented rust. However, it had the reverse effect, and trapped water, then made your car, rust to death! Now I just use roadkill. It's not as brutal, as the Tetrosyl 😉
4 December, 20:06
Peter HardyYou would love Jon Martin. Walks his own path through life.
Bozz, keep your private life to yourself, I am too young to be corrupted by the likes of you!
5 December, 10:55
yngvenettI'm in to learn! What you did with the masking tape, Mig Oil and pigment marker on the air cleaner filters looks very good 👌
6 December, 07:36
Peter HardyThank you yngvenett The idea just came to me, after a lot of lost sleep! There are some very clever people on Scalemates who will help you.
1 6 December, 09:12
Kyle DeHartJust finding this Peter. Love th color of Jon's car. Outstanding work on the air filters. That worked well indeed. I'll be following along now
8 December, 23:50
Peter HardyKyle, I am trying to replicate the colour and just cannot get the right saturation. Shade is fine, colour is fine but the best I can get is a bit dull. Never mixed my own base colour before. I have spent way too much on paint now so will have to "run wot I brung" so to speak. I'll just be wet sanding the colour paint before I 2k clear over the top. My thoughts on cars are that the finish makes or breaks the build and that most of the finish is the top of the car. Roof, bonnet and boot lid.
9 December, 02:31
Kyle DeHartThat photo you have used as photo 1. That definitely looks like a tough color to match!! Your paint color will pop nicely once you get it wet sanded and 2k'ed. Look forward to seeing it. Coming right along.
9 December, 06:27
Brandon Hдобави нов фотоалбум.
22 7 October, 15:16
István SzücsShe looks good in yellow, I love the way you weather your vehicles! The slant6 also a good idea!
7 October, 19:08
Alexander GrivonevI like the subtle weathering, the little paint blemishes, very realistic looking👍 Beautiful!
8 October, 12:22
Karl R.Amazing model! You have inspired me and I bought this model. Quick question though, how did you make the battery connectors and wiring inside the engine bay?
13 December, 23:37
Brandon HThanks all!
The battery connectors are as molded on the kit part, picked out with a dull metallic gray. The wiring is 30~32 AWG hookup wire.
16 December, 12:35
Karl R.Thanks! You'll be seeing my interpretation of this duster when it warms up enough to paint. Always learned something from you. I'm also eyeing your C1500 grilles might be seeing something along those line too.
16 December, 23:56
Jennifer Franklinдобави нов фотоалбум.
248 26 April 2023, 02:33
Robert PodkońskiGood work so far, keep it up! (and keep the parts of the model away from your assistant 😉... )
26 April 2023, 05:06
Jennifer FranklinI have to barricade my model into my spray booth whenever I am not working on it 🙂
27 April 2023, 05:14
Michael KohlHi Jennifer, you are on quite a mission if this is your first kit.
The airbrushed parts do look good.
As a hint: In case you want to orientate a picture differently, like pic 2 and 3 for example, you can do so by choosing the option "advanced" in the "manage"-menue.
May I suggest to further dilute paints you brush paint? The paint on the door seems to be rather thick. I for my part had a hard fight to alter my initial tendency to cover an area with one layer of paint - be it brush or airbrush. If you do a test brush stroke no stroke patterns should be visible. You will then probably need three to four passes to cover the intended area. Another thing that took me a long time to accept was to unload my brush on a piece of kitchen paper before I touch the model. If you then touch the model, it should not leave a drop or puddle but just a smooth thin layer of paint. Maybe this helps a bit on the way.
Keep us posted on your progress
Happy modelling
1 27 April 2023, 07:08
Guy RumpGood progress. From experience on this kit, ensure that you put the clear parts for the nose area on before painting. The fit of these is quite difficult. (masked of course). (not the actual gun transparency, that fits fine). 👍
27 April 2023, 07:16
Jennifer FranklinThank you for all the advice. In hindsight, this may have been a bit extreme for a first model. I definitely need to dilute more when I do brushwork. Thankfully that was done on the interior and should not show too much in the end. I will endeavour to improve going forward.
1 27 April 2023, 08:10
Slackbladder<<<<< I have a similar feline 'helper' who often appears, usually whilst trying to do the most tricky things.
27 April 2023, 08:20
Jennifer FranklinYes, her timing is generally remarkable, she tends to really pick her moments.
27 April 2023, 08:30
Tyson TuGreat job so far - especially for a first kit! Looking forward to seeing your progress (both on this kit and afterwards 🙂)
My helpers are generally invisible, photo-wise, but their fur (especially now in the spring shedding season) sneaks into at least half of the macro shots 😉
27 April 2023, 14:22
Michael JonkerGood luck Jennifer, it is looking very neat. I second the advice given on brush painting. Many thin coats and patience required. The fur of my two helpers are well embedded into the paintwork of my models!
27 April 2023, 17:13
NeilHi Jennifer, watching 👀 your progress with interest also, great work so far 👏👍
27 April 2023, 20:12
RuiThe cat is a vital element of the build for morale. Don't let it try to help; the lack of opposable thumbs is a detriment to assembly and sanding. Paint though is a different story 🐈
28 April 2023, 03:15
Jennifer FranklinHi Bernd, Juskifo, Tyson, Michael, Neil, and Rui. Thank you for your kind words and advice. Agreed the cat is a vital element for morale 🙂
28 April 2023, 03:25
Jennifer FranklinI tried thinning my paint before doing brushwork tonight and it helped. Thanks for the good advice. My brushwork could still use improvement but it's better than before.
29 April 2023, 02:27
Martin OostromFor a first kit, this is looking very promising! Live and learn and after three more kits, see how much your skills improved.
29 April 2023, 07:25
Rando DudeQuite an ambitious choice for a first kit, but it is also looking pretty good so far. Following with great interest.
29 April 2023, 07:25
Jennifer FranklinThank you, Bruce, Rando Dude, Martin, and Michael, very encouraging.
29 April 2023, 11:35
Robert PodkońskiJust an unimportant suggestion, Jennifer: there is a functionality in the album editing that shows the last uploaded photo as the main one - it gives us the possibility to follow the development of your work 😉
29 April 2023, 12:59
Jennifer FranklinThanks Robert, that is a great suggestion, I will do that from now on.
29 April 2023, 19:39
Tyson TuHi Jennifer, re pic 42: Dry brushing can definitely be an important skill for your arsenal, just be careful which brush you pick up to do it…I've ruined quite a few brushes picking up a perfectly fine detail brush and getting a bit too enthusiastic with it while drybrushing 😉
29 April 2023, 19:55
Jennifer FranklinHi Tyson, good to know, I won't use any of my best brushes but only my junk brushes when I do it going forward.
29 April 2023, 20:01
Robert PodkońskiYou must be very talented, Jennifer - I have never mastered a dry brush technique...
29 April 2023, 20:33
Greg BakerLooks like everyone is piping in with advice, so I'll share some… paint retardant. It's similar to thinner, but keeps the paint from drying too quickly, which cuts way way down on the brush stroke marks.
1 May 2023, 05:59
Jennifer FranklinHi Simon and Greg, thank you, Simon. I will try that Greg when I start working on the exterior. Thank you for the advice!
1 May 2023, 12:33
Jennifer FranklinThank you, Roland and Pietro. I am having a lot of fun with this model.
1 May 2023, 15:59
Greg BakerI'm a bit evangelical on paint retardant and it's the kind of thing I wish I'd known when I started out. The first time I saw it, the implications of slower drying paint were not clear to me. I mean, don't we always want the paint to dry faster? However, using it makes a big difference when brush painting.
This video isn't in English, but the results are clear to see:
Youtube Video
1 May 2023, 16:02
Jennifer FranklinI am definitely going to try it, Greg. The video's results were clear and definitely a win. I had dismissed retarder since I had thought who wants their paint to dry slower, I can see now this was a mistake.
1 May 2023, 17:03
Ludvík KružíkJennifer, you're doing great! Even though the B-17 is not the easiest kit, you're doing very well. I really like your enthusiasm for model building. I wish your enthusiasm will last and model building will bring you joy.
4 May 2023, 21:08
Jennifer FranklinThank you David, I might even finish the interior one of these days soon 😛
5 May 2023, 17:01
DaveYour work on this kit looks great, and love how supervisor is keeping watch over your progress. Mine just curls up and sleeps in my paint booth.
5 May 2023, 22:48
Jennifer Franklin*wow* Skyhiker, thank you, it is going to take me a while to go through all of that. It's a forty minute movie 😛
6 May 2023, 02:16
Edward MacKenzieWow, great work so far! Congrats, it is really looking good! But to be honest i mostly like the pics with your red/white assistant... awww....
6 May 2023, 05:36
Chan LiHave to say I never knew any lady modeller who's interested in military motif, and things look much better than my first model, looking forward to the final reveal!
6 May 2023, 07:24
Jennifer FranklinThanks, Edward and Chan, I fell in love with the Memphis Bell years ago when the movie came out. It was a lovely film. My assistant is definitely the best part of any project that I do. Thank you, Roland, very sage advice. These are just temporary holds while each 24-hour glue step sets but when I do the final glue of the two fuselage pieces (which is coming) I will try to keep that in mind.
7 May 2023, 02:22
Simon O'GormanLove watching your first build. It's really good! Love the pics with your cat in them. Also, you've inspired me to order a magnifying lamp.
7 May 2023, 09:36
SkyhikerJennifer if you will be doing more 1:72 scale projects the best investment you can make is a magnifying headset. amazon.ca/Magnifier-..stable/dp/B08F6YZLH2
7 May 2023, 11:01
SkyhikerA focal length between 12 and 6 inches is best for most things in this scale.
7 May 2023, 12:40
Jennifer FranklinOooooohhhhhh, thank you Skyhiker, I have bought the magnifying headset, that is a great idea! Thank you, Simon.
7 May 2023, 13:41
Bruce HuxtableJohn's advise is spot on. I use Fine and Extra Fine, and they are the best thing ever 👍 Use with water, and the sanding sticks last years. The extra fine makes the model smooth and shiny again 👍
7 May 2023, 16:14
Alexander Perovне самая простая модель для начала в моделизме и у вас очень хорошо получается удачи в дальнейшем
7 May 2023, 19:56
Jennifer FranklinOk Bruce, very good to have that confirmed. I've already bought the sandpaper so I am going to see if that works as my pocket book has limits but will keep that in mind for the future.
8 May 2023, 03:47
Jennifer FranklinThanks to MM Scale Models for the video that taught me how to do the weathering techniques that I applied tonight. Youtube Video
8 May 2023, 05:04
Michael KohlNice progress. Having a well organized working space doubles the fun.
May I ask which riveting tool this is? Looks pretty decent.
You may want to reconsider riveting your first model though, as riveting can be a source of quite some frustration (guess how I know).
Keep up the good and steady progress and have fun.
9 May 2023, 10:28
Jennifer FranklinThank you, Michael, it was suggested that I practice on a spoon, so I am going to try that and see how hard I find riveting to be. I imagine the real difficulty is in getting all the lines right though. The tool is by SM SunniMix: amazon.ca/dp/B09Q3D7..dt_b_product_details. I would really like to try the riveting as I kind of consider my first model to be a playground to try everything, Although scratch building I am saving for when I have more experience. I have been reading that applying the rivets to the primer layer is much easier than the bare model so I may try that.
9 May 2023, 14:00
Neil PatrickVery impressed by your commitment and investment for a first model Jennifer. I think most of us (of a certain age at least) started with just a kit, a tube of stringy glue and a vivid imagination.
I find riveting to be less hard than you'd guess at least on flat sections. Concentric fuselage circumferences need guide tapes I find. They add a lot of interest to large flat surfaces IMHO.
9 May 2023, 20:32
Jennifer FranklinThank you, Robin, Dave, and Neil. Yes, a lot of preparation and research has gone into this model. One of the advantages of being a certain age is you tend to prepare more I think 😉. I am much happier with an organized workshop. You have sold me on doing rivets Neil.
10 May 2023, 00:39
SkyhikerJennifer you will find that the size of the sprocket wheel matters when doing rivets. The smaller the diameter of the wheel the more control you will have and you will be able to reach further into the corners. Most corners will have to be individually done though. Embossing label tape helps to keep things straight. Proper blueprints are a must.
10 May 2023, 00:56
Jennifer FranklinHi Skyhiker, I have found blueprints and a very good video that goes through the process including the use of label tape. Thank you for the advice, it is much appreciated.
10 May 2023, 02:08
Martin OostromYou might want to reconsider the layer of putty that you applied, it will be a lot of work to remove the excess. The stuff does shrink, but not that much 😂
Been there, done that.
10 May 2023, 07:25
SkyhikerMartin has a point. There is nothing wrong with trying out the putty but I have found that it is only useful for certain types of jobs. Most seams can be sealed and sanded using cheap super glue and sanding sticks. It's much faster, easier to control, doesn't shrink, sands down better and it is better for making panel lines and rivets because it doesn't crumble. If you go to a dollar store you can usually pick up a pack of 5 tubes for about a dollar. I usually buy 50 small tubes at a time. Larger bottles tend to dry out and should be avoided. Cyanno accelerator will make super glue set instantly and debonder will remove super glue from delicate areas. A decent set of sandpaper can be picked up online.
10 May 2023, 09:02
SkyhikerYou can make a super glue applicator with a sewing needle. Just cut the top of the eye off to make a fork and set it in your pin vice hand drill. The super glue applicator will give you surgical precision. Put a small puddle of super glue in the wax of a tea light candle. Dip the applicator in and apply where necessary. The wax helps to keep the super glue from drying out too fast. If you make a lid for the tea light using tin foil it should stay liquid for two days and the lid will keep any dust from sanding out.
10 May 2023, 09:16
Jennifer FranklinHi Martin and Skyhiker, oh dear about the putty, I guess I am going to find out how hard it is to remove (at least from the top) and then I can try the super glue for the bottom. Skyhiker, believe it or not I found those blueprints doing searches on the Internet.
10 May 2023, 10:44
Martin OostromAnd if you add a little pigment to the superglue, it remains just a bit softer and you can see where it is.
10 May 2023, 11:18
SkyhikerDon't worry the putty should work fine. It's just the super glue is probably better in this type of application. Trying both in the beginning is the only way to know where to use each product.
10 May 2023, 12:57
Chan LiHi Jennifer, sometimes you can use the masking tape before applying putty (or whatever for same purpose) and sanding. Tape the sufaces alongside the gap, then you can sand at will.
In this case you don't worry about ruining the areas around. All rivets and panel lines would be protected by the tape, and you can even tear them off when the sanding is nearly done, saves up time, and keeps the surface neat.
10 May 2023, 15:04
John HughesLet's not forget Mr Surfacer Liquid Putty! Apply with a brush, cut back with IPA or Mr Surfacer Levelling Thinners.
10 May 2023, 15:14
SkyhikerThe art is to make perfectly smooth surfaces after filling. This requires more sanding than what you have done so far. Work your way from 200 grit to at least 800 if not to 2000. Keep your magnifying glasses on and use a directional light to see any unwanted shadows from surface texture. For a gloss surface it is advisable to wet sand up to 12,000 grit.
10 May 2023, 15:14
Jennifer FranklinHi John, I will look into Mr. Surface Liquid Putty, it sounds time saving. Hi Chan, thanks for the pro tip! HI Skyhiker, added 5000, 7000, and 10000 grit. Does that look better?
10 May 2023, 16:10
SkyhikerIt's hard to tell from photos how smooth it is. It looks like there is still a bump in the second panel of the tail. Between 100 and 600 grit is where most of the sanding should be done. Once the surface is even you can start polishing with higher grits. If you can cast a shadow in any area you should probably go over that section again. People always underestimate the prep work before priming but it is what makes for award winning work. Of course not everyone wants to make the perfect model. The main thing is to go as far as you want to and enjoy what you are doing. It is a hobby after all. But since you are just starting out it is best to learn what to look for in order to get the best results, which is why I've made these suggestions.
10 May 2023, 16:28
Shar DipreeHi Jennifer. What do you want to sand with a P5000, P7000 and p10000 sandpaper?
As long as you don't want to grind and polish clear parts (or high gloss finish), a P240, 400, 600 and maybe another P800 will work for everyone. 🙂
10 May 2023, 16:41
Jennifer FranklinOh, now I understand what you are looking at. OK, I will check for bumps. Thanks Shar and Skyhiker. I thought you were looking at how rough the surface was.
10 May 2023, 16:58
Łukasz GlińskiIf it comes to putty you might consider getting Perfect Plastic Putty
Perfect Plastic Putty (Deluxe Materials BD44, No)
Similar to acrylic ones mentioned above, can be awlays reworked using a bit of water, even when it dries completely. Not as good as super glue as it crumbles, but it's sandable as well.
Not sure however what's the availability across the pond, they make it in UK.
10 May 2023, 17:48
Jennifer FranklinThanks for the pro tip Lukasz, I will look into finding a supplier here in Canada.
10 May 2023, 17:59
Shar DipreeI can highly recommend Tamiya Putty Basic Type.
Tamiya Putty Basic Type (Tamiya 87053, No)
But just don't get it on your skin.
10 May 2023, 18:13
SkyhikerAll of those putties are decent and have there uses but for a perfectly blended professional fuselage or wing roots, standard super glue is really the best. You won't have to chase the seams over and over. It is the cheapest, most efficient, fastest and does the job better than any other product. I would only use putty for areas that need sculpting where two part epoxy would be overkill. And I would only use water soluble white putty for small areas that need to be quickly filled where sanding is impossible such as near raised elements and when using super glue with debonder would be too laborious. Believe me I know what I am talking about, I have a masters degree in sculpture and 35 years experience as a professional artist.
10 May 2023, 18:36
Jennifer FranklinOkay Skyhiker, your super pro tip has been noted. I will definitely pick up some little dollar store super glue packages. There is a store near my house.
10 May 2023, 18:48
SkyhikerI'm not sure I have super pro tips. I think for those you should ask people like Alec K, Bughunter, Spanjaard, Harvey H.W., Andrea Brenco, Jeanette Müller, Michael Phillips, or Roland Sachsenhofer and many others here as they have more experience in modeling than I do. But I'm happy to relay some of the experience I've gained in my time with this hobby.
10 May 2023, 19:17
SkyhikerI think Roland Revolvermann and Łukasz's method of using acrylic putty is good if you are very experienced or have a high quality kit that fits well together, but most kits are not like Bandai kits with perfect fits. Of course with practice any method can be perfected as Roland and Łukasz have proven many times over. Practice makes perfect, the tools are just tools.
10 May 2023, 20:38
Łukasz GlińskiFully agree, this forum is about supplying all of us with options, but we choose ourselves what to pick, there's no one&only way to perfectly build any given kit 😁
10 May 2023, 20:49
DaveI agree with the gentleman above and their Points of view. A lot of it is experiencing what works for you. On that particular kit you're working on. I know me and I have lot to learn still. That what makes it fun.
11 May 2023, 01:59
Jennifer FranklinSky you must have an incredibly good eye, I had to use a ruler to find the bulges. I did some more sanding and added a grey primer to try and "pick up" inconsistencies. It's not absolutely perfect but I think I may call it good enough.
11 May 2023, 02:31
Jennifer FranklinThanks, Dave, a very good perspective. And yes, this is terribly fun isn't 🙂
11 May 2023, 02:40
Shar DipreeHi Jennifer. With a black primer (and some playing with the light angle)you can see inconsistencies in the surface better than with grey.
11 May 2023, 04:56
SkyhikerJennifer I think you are starting to get a feeling for what to look for. Congratulations. Surface structure, blended joints, clean edges and proper lines in the structure are the best things to concentrate on at this stage. As well as making sure you have clean and transparent clear parts and proper masking. Later you should look at the overall structure such as the angle of the wings and landing gear. Then move on to focusing on the painting; making sure your paint doesn't over extend or under extend the intended area, and making sure you have smooth surface layering, correct hues and values, and proper transitions to your various layers of paint and clean edges where necessary. Once you know where and what to look for it's is just a matter of practice and a desire to improve with each model that will make you proud of your talent and success. Welcome to the wonderful world of modeling!
11 May 2023, 05:09
Jennifer FranklinThank you, Shar for explaining the grit levels I should be using and Sky for pushing me to get it right. It looks so much better now.
12 May 2023, 00:23
SkyhikerAny behind the scenes action going on with this project? Been a bit quiet lately.
15 May 2023, 01:20
Jennifer FranklinYou have excellent timing Sky, you asked roughly an hour before I posted my latest update.
15 May 2023, 03:00
Jennifer FranklinSo I found a good video on how to fill seams. Youtube Video Thanks to everyone for all of their great advice.
15 May 2023, 03:40
RandoThe Eclipse HP-CS is the first and only airbrush I've bought, it's done really well for me so far, hope you enjoy it!
15 May 2023, 15:55
Jennifer FranklinThank you, Rando, I am looking forward to trying it out tonight after work.
15 May 2023, 16:00
Shar DipreeYes, the Iwata Eclipse (0,35mm) is a great, unproblematic and universal airbrush.
The switching from two different Harder & Steenbecks to the Iwata Eclipse was like a revelation for me. My partner has since changed too and is also totally happy. I am convinced that you could not have bought a better one for model building and as a beginner.
15 May 2023, 17:36
SkyhikerI have an old Iwata hp-b 0,2 mm that is a bit difficult to use because the trigger pressure is very sensitive. I'm curious if those issues have been fixed? I'm sure they have since my Iwata is over 30 years old. Perhaps I just need to replace my valve with a newer one.
15 May 2023, 17:50
Jennifer FranklinThank you, Shar. Sky you should replace your valve for sure, the Iwata is wonderful to use. I used it over my lunch break and it was mind-blowingly better than the starter kit that I was using.
15 May 2023, 19:49
Ludvík KružíkJennifer, it's clear that you have put a lot of effort into the preparation and that you really enjoy building the model. It's amazing the progress you've made. 👍 I wish you continued success!
17 May 2023, 11:40
Jennifer FranklinThanks, James, I have to admit I am a little nervous about the riveting, weathering, and decal steps coming up. I have bought plastic spoons to practice on.
21 May 2023, 04:41
Simon O'GormanPlastic spoons rock! Just learning myself and, along with cocktail sticks, they are my new favourite accessories... I'm mostly in this for the accessories!
21 May 2023, 06:39
gorbyI'm amazed you are attempting so many new techniques on your first model. Very nice work so far.
21 May 2023, 07:22
Robert BarkoskiGreat work so far! I'll admit, I like the idea of using zip ties to hold the fuselage together while glue dries. Keep going!
21 May 2023, 08:28
Pietro De AngelisNice progress so far Jennifer considering it's your first model,
congrats!
21 May 2023, 08:39
Jennifer FranklinThank you, Simon, gorby, Robert, and Pietro. Yeah, I love the accessories too! I am building my collection of "tools". Once my wings finish drying I need to go back and straighten that one engine, I just noticed it's fairly askew.
21 May 2023, 10:35
CuajeteMates advice are very much appreciated. Well done so far, Jennifer! 👍
You have a very nice furry assistant 😉
27 May 2023, 17:57
Martin OostromCheck out my album to see what you can do with spoons, bamboo sticks and a cat toy WIP - MyFirst Gundam | Album by Mahoo76 (1:144)
27 May 2023, 18:19
Jennifer FranklinThank you Cuajete, Martin, and Shar. Things are taking shape and it is getting exciting. Mates are indeed greatly appreciated. The truth is I actually have two furry assistants who are almost identical looking, although most of the photos are of my girl Framboise. Loki is clumsy enough that I rarely allow him near my model. Very nice album Martin, I especially love the primary coloured spoons.
27 May 2023, 19:56
Remco van HarenGreat work so far! Not exactly a beginners kit, but you're doing a great job.
27 May 2023, 22:11
Jennifer FranklinYeah, it was suggested that I pick a subject that I was interested in so that I stay motivated and I absolutely love the Memphis Belle so... how hard could a Revell Level 5 be right? lol... oops... but I have to admit I am enjoying the kit immensely so even if it does not turn out as perfectly as a lot of the work I am seeing on this site, well it will be a great learning experience and my next kit will be that much better.
28 May 2023, 02:02
Mr JamesAgree with everyone else with how well you're doing on your first kit. Nice work on the interior. I'm impressed with your organisation and professional approach to building. Also, you've got a great setup with your spray booth and an excellent choice in the Iwata Eclipse, I have the same one. 🙂 My tip of the day, if you dont know already, is to pop a couple of beads into your paint pots. I use Non-Magnetic Hematite Beads, £2 for 100 @Amazon. They dont corrode or effect the paint and really help in shaking the paint ready for use. Especially if you use Vellajo acrylics, which are really good for brush painting.
28 May 2023, 03:39
Michael KohlI actually prefer simple stones that I washed before. They are dirt cheap and absolutely never ever corrode. 🙂
Your build is great to follow not just for the quite impressive progress you are doing on the fly as you devour all the input, but it is quite interesting to see how others approach problems and which tricks they use. And all of that in a nutshell.
Continue to have fun!!
28 May 2023, 17:46
Jennifer FranklinThank you, Mr. James, I am using metallic beads of some sort that I bought on Amazon, I agree they are great. Hi Michael, I had not thought to use plain stones, that is a terrific idea.
28 May 2023, 18:58
Jennifer FranklinI am struggling with my right engine cover. I accidentally glued it askew and I can not figure out (yet) how to correct it. I used superglue in this case. I have tried taking some plastic cement and using that to separate the parts but since there is superglue in there not too surprisingly that did not work. I have ordered some glue debonder and will see if I can make that work but if anyone has any suggestions please let me know.
28 May 2023, 18:58
David HYou can get debonder but I haven't used it and don't know how it would react with the plastic 😬
28 May 2023, 20:43
Michael KohlDo not have any experience with debonder, but superglue is quite brittle and often parts can be separated again by flexing the contact lines. I would try to pry the two parts a bit apart (best at a rather invisible spot).
28 May 2023, 21:17
Ludvík KružíkPlastic glue does not dissolve CA glue. It would only damage the surface of the model.
Most debonders (CA glue solvents) do not react with plastic, but it is better to test them on a piece of plastic tree for example before use.
It is also possible that the debonder will not penetrate deep enough into the glued joint and dissolve all the glue.
As a possible solution (if all attempts to unstick the engine cover fail) is to cut the engine cover off with a razor saw. This saw has a very thin cut and the loss of material at the cut point is minimal. Carefully cut off the engine cover at the joint. After cutting, sand the mating surfaces so that the engine cover is in the correct position and glue the cover back in place.
And of course check the correct position of the cover during gluing. 🙂
28 May 2023, 21:35
Jennifer FranklinHi David, Michael, and Ludvik, okay thank you all for your advice, I will definitely test the debonder on one of my sprues before trying it on my model. I have tried prying the two parts a bit apart and that is not working. I have bought a mini razor saw and will pick it up tomorrow, let's see how well that works.
29 May 2023, 02:07
SkyhikerAny CA debonder will work. Just put it on and wait for 10 minutes. You may have to reapply a few times if you want to get all the super glue off. This is what I use... Glue Buster 28g (Deluxe Materials AD48, No)
29 May 2023, 17:13
Andy HeimA nice piece of work for your first project!
Keep on, it will be a very good start to scale modeling.
The only risk is, that your cat wants to play a little bit with it 😉
31 May 2023, 15:43
Jennifer FranklinHi Andy, I am actually building a plastic cover completely around one of my shelves to protect my finished model, complete with a hinged front using magnets to secure it so I can open it whenever I want. Believe me, I am planning on protecting my baby when it is finished. At the moment I have a cardboard-covered area protecting it until I finish the plastic shelter. 🙂
31 May 2023, 17:07
Bruce HuxtableThe riveting is looking very neat and I'm sure will add greatly to the finished appearance. Don't rush it!
31 May 2023, 17:31
Shar DipreeIt's really impressive what you do. I'm beginning to think that you're not really a beginner, 😉
31 May 2023, 17:38
Jennifer FranklinI thought I was making enough rookie mistakes between my initial rough brush painting, the lack of use of flow improver, my seam filing, gluing the wings before doing the rivets, and gluing things at an angle that is so bad I am going to have to correct it 😉
31 May 2023, 18:46
Mr JamesSound like a normal build to me... 🙂
I've made more mistakes on planes than anything else. Leaving things out after fuselage glued... 🙁
31 May 2023, 18:52
David HShar, maybe our Jennifer is a ringer and really is the lady that does Jenesis models on you tube 🤔🤫😉
31 May 2023, 19:19
Tini HendriksWith so much advice you will be able to fly the thing 😀. Very nice to see your journey in words and pictures! 💪🏼
31 May 2023, 19:47
Robert BarkoskiAs a cat lover, I get where you are coming from. That "security box" is priceless!
8 June 2023, 02:59
Jennifer FranklinThank you, Robert, Cuajete, Simon, and Mona. Let's hope the cats decide resistance is futile, when they put their minds to it they can do some pretty amazing (and destructive) things.
9 June 2023, 09:46
Andy BallAs I understand this is your first go at model making?, well what a great start and super methodical too! Look forward to the finals at RAF Bassingbourne!
9 June 2023, 14:58
Jennifer FranklinMona, that is really sweet. My older girl might well sleep with my model but my younger boy likes to play and I don't think the model would survive him. Thank you, David, and Andy. Yes Andy this is my first model 🙂
11 June 2023, 04:35
Ludvík KružíkJennifer, I hope all is well with you. I haven't seen a post from you in a long time about your Memphis Belle.
29 July 2023, 12:15
RobbieWhy modelers have cats is beyond me. Dogs don't trash your display case or your man cave. I can't see myself bolting plexiglass around everything just so furball don't mess with it ;P
29 July 2023, 23:46
John HughesLudvik, I suspect the recent fires may have forced Jennifer to relocate for a time. Hopefully she'll be back with us soon.
30 July 2023, 09:32
Jennifer FranklinI am well, I have stayed in touch with an old friend from high school and he recently had severe health problems I have had him move in with me and it has taken up a fair bit of my time. I plan to get back to my modeling work soon.
12 August 2023, 20:47
Ludvík KružíkI was very pleased to hear that you're all right. 🙂
... and I look forward to continuing your work on the Memphis Belle.
14 August 2023, 09:43
Jennifer FranklinI have finished decluttering my basement and moving everything in my guest bedroom closet downstairs so my guest now has a full closet, almost back to the model 🙂 Thanks everyone for your kind thoughts.
25 August 2023, 03:39
David HAaaaaaand we're back. Missed you Jen. Glad you're ok and back in the saddle 👍🏻
19 January, 21:55
DaveGlad to see you're back. Hope everything is ok and that supervisor (aka kitty) is still keeping watch over your project.
22 January, 01:29
Jennifer FranklinHi Dave, my supervisor is still active. My friend is fully healed, and I have mostly finished training for the new job, so I am very glad to be back, thank you.
22 January, 11:42
Ralf TopetersNow I meet the plane build! I've only seen the dio album so far. Following of course!
24 January, 15:13
Mr JamesI didn't realise how big that 1.72 model is. Are you going to metal finish or olive drab affair 🤔
24 January, 20:41
Jennifer FranklinThanks for the chuckle Mr James. Yeah, classic Memphis Belle colours for me.
24 January, 20:59
DaveJust had a quick look at some of your photos and have admire the details you added to the kit.
25 January, 00:50
Jennifer FranklinThank you, Dave. High praise coming from a more experienced modeler.
25 January, 02:27
Michael KohlYou might consider putting a cardboard on the bottom of your spraybooth and an aluminum wrap around the sides. Keeps the box longer in presentable shape. I personally like to quickly test shoot my gun adjustments on the cardboard too.
Repeating my mantra I definitely recommend a respiratory mask in addition to the booth. Whenever I change the filters I am amazed at all the stuff my lungs did not have to handle. Costs only as much as a decent kit. Choose the appropriate filters for your needs. And I was surprised at the minimal impact on respiration.
25 January, 12:06
DaveJennifer thank for the compliment. But let's be honest I'm old enough to know better but young enough and dumb enough to do it again.
25 January, 14:47
Patrick HagelsteinI'm 🤞🏼🤞🏼 for you Jennifer, that exterior paint session is both the most nerve wrecking and rewarding experience of the whole build. Enjoy this part! ☺️👍🏼
25 January, 22:16
Jennifer FranklinThank you, Desert Marlin and Patrick; I will try to enjoy the exterior paint to the fullest that I can.
25 January, 23:55
StuartHi Jennifer, I have found theses PDF step by steps are really helpful if you are keen.
acrylicosvallejo.com/en/step-by-step/
26 January, 11:44
Jennifer FranklinHi Stuart, those step-by-step PDFs look like a great help; thank you!
26 January, 12:34
Ralf TopetersAbsolutely! Thanx a lot Stuart! 👍 I haven't heard of them so far and they look great.
26 January, 22:44
Tom HarrisGreat work, Jennifer! For a first kit, you're REALLY diving in! 🙂 Rivets! 😮
Also great that everyone is pitching in with help!
I found myself chuckling because your tool setup is so familiar! Almost the same model spray booth, 3-brush set, same airbrush pot/holder, folding table, similar iwata airbrush and I nearly bought those wooden-handled tweezers (how are they working out?)!
27 January, 02:44
Jennifer FranklinWelcome, Tom, and thank you. Interestingly, we have a similar setup, as I did not buy all my equipment from one place. Are you new or recently returned to modeling? The community on this site is lovely and has been a big help as I have progressed through this first build. I love the wooden-handled tweezers; whenever I need a third hand, they are the first thing I pull out.
27 January, 04:49
Ludvík KružíkPainting and gluing decals -this is my favourite stage of model building. It's the exact moment when a piece of plastic becomes a real model.
Keep up the good work!
31 January, 23:44
Jennifer FranklinThank you, Skyhiker, Ralf, David, and Ludvik; I have to admit this is exciting. I am getting close to finished!
1 February, 01:10
Casey BeckettUnbelievable first effort - my first Memphis Belle at oh, say 8 , way back in the early 70's was done in one afternoon....very impressive.! following.
1 February, 01:58
Jennifer FranklinThank you, Casey; between when I started and now, I am already embarrassed by many of my early mistakes, but it has been an absolute joy to learn as I have gone along.
1 February, 02:26
SkyhikerEach model is a new learning experience if you challenge yourself to improving. I find that is the real joy in modeling.
1 February, 04:16
CaptGPFOur hobby is definitely more fun with our four legged assistants! I can relate to the need to keeping the crew and kit secured while you are away, cats seem to like taste testing the pilots. 😀
1 February, 15:34
Jennifer FranklinThank you, Skyhiker, Akaidada, CaptGPF, Nathan, James, David, and Cuajette. Have loved learning along the way with this model and could not have done it without my 4-legged helper.
2 February, 02:37
MunkyslutThat's coming along beautifully………. everything you do looks so clean & neat, quite impressive👌👌
2 February, 23:37
Jennifer FranklinThank you, Mark; I have learned not to spray toward masking tape (I really should have known better), and I get to clean it up this afternoon.
3 February, 16:29
Jennifer FranklinI cleaned up my messed-up paint job, but I have received feedback that I may need to do more sanding, possibly filling, and seam cleanup. I am going to go through all the suggestions I received and see what I can do. Expect a potentially much smoother model soon-ish. Through some minor luck, I managed to match the paint mix again almost exactly to the first mix of the olive drab.
3 February, 18:28
Rudy PoseikaSoonish: time is relative when you are developing software or making a model. Looking good at any rate!
3 February, 18:42
Mark SherwoodYes, Jennifer. Clean up. I bloody love that when I've cocked up a paint job. Wet and dry, sand the offending edges and holidays then respray 😤 Good luck Jennifer. 🤟🥸🤘
3 February, 19:22
Jennifer FranklinThank you, Mark; wish me luck matching the paint. Both the top and bottom are mixes. At least I can rely on weathering to smooth out some variation.
3 February, 19:55
Jennifer FranklinTomorrow, I will be buying a scribing tool to rescribe panel lines. I still have some paint cleanup to do, too.
4 February, 02:50
Michael KohlOnly one?
Sorry to elaborate again, but maybe you'll find the info valuable nevertheless.
For (re-)scribing panellines you will encounter various situations that are best dealt with with different tools.
What's the shape you need? V or U? Most of the times it doesn't really matter, sometimes it does.
I take the liberty to just state what I use:
- saw: gives you a very good guidance as you can start at the still present panelline and continue into the panelless area. Creates a U-shaped groove. JLC is a classic, a lot of other brands and shapes are available. Blade width shouldn't exceed 0.2 mm.
- UMM scribing tool: has two ends and can be pushed and pulled. Sharp. External guidance recommended (ruler, tape or the like). Creates a V-shaped groove.
- punch: best for irregular shapes. Creates a V-shaped groove. Needs guidance. Works best with PE-templates (consider ordering some). Looks for ones with a wolfram-carbite tip. Gives you more punch for your buck.
- Scriber
+ Trumpeter: coarse and cheap. I like it for coarse work like cutting sheets. V-shape
+ Tamiya and others: Very expensive. Can only be pulled. Available in various widths, U-shape
- phiole/ampule cutter: dirt cheap. Properties similar to saw (highly recommended by my Master Modeller friend)
I got them all. I use the top three for 95% of my scribing. Buying UMM tools hurts - but only once. Then you should have a trusted mate. (Similar to Tamiya, but for scribing I would choose other options).
Hope that helps and doesn't confuse too much.
4 February, 15:23
Jennifer Franklin@Michael Kohl, yes, thank you, that was valuable information. I would go to my local hobby shop and see what they suggest, but now I may combine the local store and Amazon. I already have a saw, and I will check its blade width. I had no idea I could use it for scribing.
4 February, 15:39
Jennifer FranklinHi Clifford, this is my first model, so I don't have a lot of context. I've found it to fit and be fairly easy to build generally. Have you built the 1/48 one? My modeling buddy is great.
5 February, 00:49
Jennifer FranklinOh shoot, it looks like I got the camo colour wrong... *sigh*. Guess I will figure out how to clean that up tomorrow. I hate my life right now ☹️ And I did three rounds of it without noticing it was wrong. *super sigh* So mistakes were made...
5 February, 01:46
MunkyslutWhat's wrong with it? Looks pretty good from here👌
Remember there were loads of variations of colours & finishes, especially on aircraft in service.
I still go by the "if it looks right, it is right" rule of thumb😂🐒
5 February, 01:58
John EDealing with mistakes is par for the course. Like the time I cut the fuselage door on the wrong side. Or the time I used decal film instead of decal softener on a decal. Or the time....haha. You get the picture.
5 February, 01:58
Jennifer FranklinYeah, maybe I will just leave it, there was a huge variation in the various aircraft in service. Does anyone know how best to remove paint if I decide to "fix" it? Thank you, John and Munkyslut, for your feedback.
5 February, 02:03
Jennifer FranklinI triple-checked the color Revell said to use, and I have it right. I am using what Revell says to use. It just does not match the photos of the restored Memphis Belle. Thank you, Ben. I think that will help me make a final decision. I am keeping it.
5 February, 02:13
Clifford KeeslerI have not built the 1/48 one yet. I looked up the 1/72 kit and think I will get me one much more detailed than the 1/48 one. I have seen the real restored Belle and she has what would have been a "factory fresh" paint job, so the colors on your in service version are likely more accurate. I must say you are doing a beautiful job on your first model.
5 February, 02:20
Mr JamesAbsolutely nothing wrong with the colour Jennifer. As mentioned, you're displaying an in service aircraft. Once you've sealed it and added your washes and weathering oils ect, it'll be spot on 🙂
Can only agree with others on what a good job you're doing.
5 February, 02:42
CaptGPFRegarding paint removal - If you use acrylics, windex / isopropyl 99% alcohol will remove it for you. If you use lacquer, go with Mr Hobby Leveler - DO NOT USE MR HOBBY CLEANER - as it will literally melt the plastic!
When removing paint, it's best to mask of the affected section and carefully wipe the paint off bit by bit. That way, the panel lines will mask the differential of the paint layers. You may want to rescribe some of the panel lines of the cleaned up area as the fluid will not reach those areas.
Lastly, reprime or re-layer the paints the same way you did for the other sections to keep it level. Like John, I think everyone here has had to remove paint in the past. 😀. That said, I think the paint looks good, I would keep it as is, or if you would like, maybe applying a filter to it may tint the color to something more to your liking rather than stripping off all the paint.
Good luck!
5 February, 02:44
Jennifer FranklinThank you, Clifford. Best of luck with the 1/72 kit; I have certainly enjoyed it. I would agree the light green would likely darken and if Revell is wrong, oh well, I like the colour. Thank you Michael, Mr James, and CaptGPF. I am not sure it is that I am doing such a great job as such a fantastic community is mentoring me. I appreciate the notes on how to remove paint CaptGPF. I won't be doing it in this case, but I am confident it will be helpful. It is only a matter of time before I want to remove the paint in some other case.
5 February, 03:30
Shar DipreeHi Jennifer.
I also had to remove the paint from my mosquito once. For more:
De Havilland Mosquito B.XVI at bombing | Album by Shar (1:72)
I used the following product and it worked great. Be sure to wear gloves.
Paint Killer (Carson Modelsport 500908113, No)
5 February, 06:24
Jennifer FranklinAwww, thank you, Nathan. Thank you, Shar; I actually remember that, as I could not understand why you did it until you explained as the original paint job looked okay in the photos. That is good to know.
5 February, 11:30
SkyhikerJennifer are you using Revell enamel or acrylic? Revells colors are approximations they are not anywhere near Federal Standard colors. Back before the Internet nobody cared if the colors were accurate. Modeling was something you did as a kid or after you retired. Don't worry about the colors too much. If you want to make things accurate then go for it on your next model.
6 February, 03:39
Mark SherwoodLooking good Jennifer, in service aircraft, doesn't matter what the base colour (Even a close approximation) looks like as operational wear and tear degrades it. And as you say weathering will cover it. It has saved a build I've done (All of them 🤣) many a time. 🤟🥸🤘
6 February, 07:43
Jennifer FranklinThank you, Skyhiker, Mark, and arron.
@Skyhiker I am using Revell acrylic. On my next model, I will be more careful with the colour.
6 February, 11:34
David HJennifer, the base colour looks perfect, can't see anything wrong. I custom mix ALL my colours. If mine were as good a match I'd be really happy. 😃
6 February, 17:37
Casey BeckettAre you enjoying yourself Jennifer? Then keep on right the way you are. Too many armchair experts. This is supposed to be fun, not a constant criticism/correction/ wrong paint shade barrage. My first 1/48 Monogram B-17 (A Christmas gift the year it was released, I BRUSH PAINTED TERSTORS KELLY GREEN. And I had a blast. That same summer, a fella had come to inspect our furnace, saw the Great Green Beast in the basement, and LOVED IT. Imagine my grin when this "really old guy" (to me,) turned out to be a WWII Eighth AF mechanic, and and actually worked on B-17s . Gonna build a purple P-51 and post it here.
HAVE FUN, THAT'S the whole point.
7 February, 02:06
Donald Dickson III have seen nothing but EXCELLENT advice given in a very constructive and educational manner, as would be expected from the even more excellent modelers presenting it. I would suggest re reading what was said. Jennifer thought she was using the wrong shade. She brought it up. The other folks actually said what she was doing is perfectly fine. I saw no barrage.
Jennifer, for your first model you bit off quite a mouthful! Not an easy kit to deal with given its age. And you have been nailing it. Youre doing proper research and getting absolute top notch advice. Nothing I can add to what the others have said. Keep cracking, I look forward to seeing the finished product!!!!
7 February, 02:22
Jennifer FranklinThank you, Casey; I am indeed enjoying myself immensely. I have appreciated all of the advice and direction that I have received from the many experienced modelers on this site. Thanks to everyone's input, I have learned a great deal, and I love learning. I enjoyed the story of your great green beast, and I look forward to seeing your purple P-51.
7 February, 04:17
Jennifer FranklinThank you, Donald! I hope to have a finished product ready to show in roughly three weeks. Another couple of days on camo, a week for decals, and another week for weathering, with a layer of gloss after each stage.
7 February, 04:20
Bruce HuxtableAll that effort on the rivetting is paying dividends, Jennifer. The painting looks great, and all the fine details show up really well. I'm enjoying the paint scheme that is slowly emerging, and can't wait to see the next installment of your progress 🙂
7 February, 09:55
Jennifer FranklinThank you, Bruce. I am happy the riveting work is paying off; it was rather time-consuming and attention-demanding work. Doing the exterior paintwork is exhilarating; another installment is soon to come.
7 February, 12:19
Łukasz GlińskiIf you keep enjoying this, that means you're on the best path to success - be happy with what your build 👍
You might not have spotted it yet, but you achieved one more unintenional success - for the 1st time ever I started thinking "hm, maybe I should get myself a B-17 too?" And I would be surprised to find I'm the only one here
Last but not least - that's one of the busiest threads lately too 😄
7 February, 20:57
David HWell, I already have one (Airfix) but it's got me thinking about actually building it 🤣
7 February, 22:39
Jennifer FranklinThank you, Lukasz, Rudy, and David. I am enjoying this, and I am happy with my build. Seeing what you three could do with a B-17 build would be amazing.
7 February, 23:41
Jennifer FranklinThank you, Ludvik; coming from all of the senior builders, yourself included, these compliments are making me blush.
8 February, 01:13
Clifford KeeslerIt is looking great. Are you sure it's your first model? Lol. You should be very proud of what you have done so far.
8 February, 02:38
Jennifer FranklinThank you, Clifford. Did you see some of the early shots of my detail painting when I did not know to thin the paint or use a retarder? Or the first time I filled a seam line? Or when I glued two parts to my spray booth? Lol, it is definitely my first model. I will never forget this model. Others may blur in my memory but I suspect this one will always be somewhat special.
8 February, 02:52
Clifford KeeslerThey usually do. My first one was a freaking mess. I got glue all over it and did not even attempt to paint it. I think I was like 8-9 years old. I did not start using an air brush untill about 5 years ago, I knew nothing about washes, clear coats, PE or trying to scratch build anything. It was not untill a friend of mine told me about scalemates that I really discovered the joy of modeling. I have made so many friends and learned so much from the wonderful people on this forum.
8 February, 03:01
Jennifer FranklinYes, this is a beautiful community. I have learned so much already, and I am sure I will continue to discover more. I have four models lined up to do when I finish this one.
8 February, 03:04
Jennifer FranklinThank you, Skyhiker, Carlos, and Dietmar. I ran late tonight, hoping to get a layer of varnish by Friday morning so I can start the decals on Saturday. Only to belatedly realize that the varnish will require at least 48 hours to dry, not 24 *sigh*.
8 February, 08:05
Tini HendriksNow, coming in the last phase of this project, do you already know what the next will be 😬?
That's part of the fun too 😉
8 February, 08:23
Jennifer FranklinYes, I plan to build the Revell Big Boy Locomotive next. 😁 It's in my Stash.
8 February, 08:33
Bruce HuxtableHere, here, Clifford 🙂 Advice on problems encountered, as well as feed-back on our creations, adds to the enjoyment of our hobby. Being inspired by the work of others has been a big part of this community, for me too 🙂
8 February, 13:09
Ludvík KružíkJennifer, you don't have to blush. Although I have been building models for a long time, I still (like you) see in my models that there is always room for improvement.
And this is a great place to find lots of new ideas, experience and friends to give you advice.
And that's what it's all about. 🙂
8 February, 13:19
bughunterJennifer, I scrolled today through your build log. Impressive fast learning! It is may be not a perfect model (believe me, there is no perfect model). But the next one will be better! And you benefit greatly from the community here and can build on the experiences of others and learn from _their_ mistakes, which saves time and money not having to make such mistakes yourself 🙂
I had to grin when you glued the part onto the airbrush booth. I knocked over a large can of Revell Airbrush Clean in the booth and it still looks like that today. The stench was intense, but I was able to blow it off using the booth.
Don't put yourself under pressure to get a perfect result - the fun is much more important!
8 February, 22:56
RandoThat's a really interesting splotchy camo it had to break up the outline, looks like something that was added after it was deployed. I like how it's kind of faded and inconsistent in places, makes it look asymmetric and authentic. 👍
9 February, 00:57
Dave BrownKeep up the good work, Jennifer. If you could have seen the first model that some of us older folks built,it would bring an even bigger smile to your face. I think you've done a great job with it.
9 February, 02:30
Michael SchubertYou've done a great job so far, and it's great to see the addiction starting with the stash starting to grow haha, it's the one vice I beleive is good 😅 love the "Big Boy" Loco!
10 February, 00:23
RuiCareful with that stash. Before you know it your home will be wall to wall shelves to hold all the kits. 😁
10 February, 03:32
Guy RumpI agree with Martin 🙂 she who must be obeyed was not happy when she looked into my stash cupboards! 🙁
10 February, 08:47
David HOMG yes, beware of the stash monster. Like coat hangers , It multiplies all on its own.
10 February, 09:35
Ludvík KružíkThat's right. The ability of most of us to buy new kits is significantly higher than the ability to build them. Which inevitably leads to ever more crowded warehouses.
I've told myself many times that I won't buy new kits until I've built at least some of the ones in my warehouses. But there was always a kit that I just had to buy 🙂.
And I'm also very lucky in that "she who must obeyed" supports me in my hobby and also buys me (maybe for Christmas or birthday) new kits 😄.
10 February, 09:59
Jennifer FranklinThank you for the stash warnings; I decided I wanted to build planes that Canada flew as part of the British Commonwealth Air Training Plan next (well after my Big Boy and my Titanic birthday gift). They are hard to find, so I decided to "preorder" them as it took weeks for me to get each of the ones that I have. I will try to stay disciplined and only buy one on completing one in the future.
10 February, 12:56
David HThat's the best way Jen. Until that "once in a lifetime" kit then another. Just be strong and if the stash outgrows the store, I'm happy to look after the "excess" for you 🤣
10 February, 14:58
CaptGPFI plan on finishing my stash - even if I have to come back from the dead to do so!!!! Oh look! Sprue brothers has another sale….
10 February, 16:04
John EJennifer, there's some great color footage of WWII Canadian training aircraft in the movie Captains of the Clouds with James Cagney. Check it out sometime. imdb.com/title/tt0034578/?ref_=ext_shr_lnk
10 February, 18:40
Jennifer FranklinToo funny David and CaptGPF; Glad you'd be there for me David... lol. Thank you, John, very much!!! I have an Avro Anson at my local museum. The Oxford was flown in Western Canada and I am in Eastern Canada so I will have to live with museum photos. I will definitely check out the Captains of the Clouds footage.
10 February, 21:04
Marcel ChmuraThat's a great looking B17. Have some bombers of my own in the stash and you're build is quite inspireing. Good job. 👍
11 February, 20:14
Clifford KeeslerLooking very good Jennifer, yes beware of the stash. It will sneak up on you. I will kick the bucket before I can build all of mine, but I keep buying them anyway. My kids will have a field day when I die. Lol.
11 February, 20:56
Jennifer FranklinThanks, Marcel; her name is Framboise, and she is the boss 😛. Thank you, Clifford; I am putting in a build-one-buy-one rule now that I have four models. I wish you luck with yours, how many do you have?
11 February, 22:23
Michael SchubertReally coming together now!! Looks way way better then my first model 😅 the build one buy one is a great way to contain the stash haha I have 40 odd in my stash, and it makes it hard to know what to build next haha
12 February, 09:03
Jennifer FranklinThank you, Michael. 40?!? *wow* that is a lot of money. Options are good, though 😅. If I could do the build-over, there are many things I would improve on, but you have to start somewhere. Overall, I am happy with my results so far. I am looking forward to weathering and putting the landing gear on; I am so close to finishing now it's hard not to get excited.
12 February, 09:16
Łukasz GlińskiOnly 40? I must be approaching 3 hundreds me thinks 😁
Still doesn't feel like the time to call a therapist (or psychiatrist) 😋
12 February, 20:01
Jennifer FranklinThank you, Dick; I'm finishing it just in time for Apple TV's "Masters of the Air" series to be aired. Yes, we definitely both like the big planes 😉.
12 February, 22:00
Clifford KeeslerWould you believe 836, that includes kits and aftermarket goodies. Plus I have stuff I have not counted yet. That is why I will never get them all built. Lol.
13 February, 02:12
Donald Dickson III have somewhere around 200. Haven't counted lately. LOL
Finish line in sight. Looking good!
13 February, 02:33
Jennifer FranklinThank you, Donald. Oh my "goodness," 836, 300-ish, 200-ish, that is a little mind-blowing for me. That must have taken a while to build up, I am assuming.
13 February, 02:37
Bruce HuxtableI've just been watching some Masters of the Air clips on You Tube, and to see the bravery of the crews is sobering, especially as they were generally so very young....
13 February, 12:45
Jennifer FranklinThree of my great-uncles flew on B-17s during the war. One died, and I had the fortune to get to know the other two. They were remarkable men.
13 February, 14:09
Tini HendriksI think you will also keep the record of the most comments for a model 😉😜
13 February, 15:35
David HIf we're including accessories, AND decals ? I have 2 lever arch folder brim full with decal options. Let's not mention reading and eduard… don't think I want to count 🤯
13 February, 21:32
Jennifer FranklinYes Tini, I think I will owe a lot of rounds of beer to folks when I finish this model. @David, this is all just mind-boggling.
13 February, 21:43
Jennifer FranklinDesert Marlin, I could not agree more, they are a great buy for the price. In the next photo, I did the propellers using the flush cutters and the caliber of my result was so much better.
14 February, 05:01
David HJen , some advice with cutters. If you are cutting small fine pieces like ,say, undercarriage parts or pitot tubes. If you try to cut the part from the sprue the risk (as it's still attached at points) is the tension can snap the part . Try cutting the sprue lugs from the tree. You can then cut the lugs off without the tension as it's not attached to anything.
14 February, 08:26
Michael SchubertGood tip David, it also often means a steer angle to be able to smoothly cut coler to the model after being removed from the sprue 👍
But a good pair of nippers does make a huge difference Jen
14 February, 08:50
John HughesFor really long thin parts, carefully saw through the sprue between the connection points.
14 February, 10:21
David HThat's exactly what I was saying John. Thankyou for putting my thoughts into words clearer than I did 🤣
14 February, 10:55
Jennifer FranklinThank you, David, Michael, and John. I appreciate the advice. I also have a small saw so will keep in mind when to use it.
14 February, 13:26
Jennifer FranklinI completed the weathering. I still have to do the engine's oil/rust/smoke and the landing gear/finishing details, but otherwise, this is done. Does this weathering look all right? The oil will take a week or more to dry, so I have time to correct it. I will post more photos tomorrow with it in the sun. Oh, and I have to put a matte varnish on the entire thing as a final step.
16 February, 01:44
Jennifer FranklinThank you, Jacquline. I've put up photos of it in the sunlight. Is the weathering good guys? Can I put it in the dehydrator and set it?
16 February, 16:31
Jennifer FranklinThank you, John and Marco; I appreciate the feedback. I did not want to set the paint until I was sure I should not remove or rework what was there. I scrubbed the wash in the direction of the airflow, and I left it what looked like a reasonable amount of grimy but I appreciate a few extra sets of more refined eyes confirming that it is ok.
16 February, 18:47
John HughesCheck out some images of B-17's online. Note the smoke smudges leading back from the engine nacelles, both above and below the wing. You might like to have a go at those for a bit more detail, but don't overdo it.
16 February, 19:28
Clifford KeeslerLooking great Jennifer, It is going to be very nice when finished. You can be very proud of your first model. I think I got back into to model building around 2014 or 2015 so that stash has built up since then.
17 February, 05:10
Ludvík KružíkMemphis Belle is just a few steps from the finish line. Your honest preparation for building the model has paid off.
17 February, 08:47
Jennifer FranklinThank you, Clifford and Ludvik. Okay, roughly ten years to build that big a stash makes it more reasonable but that is still roughly 90 models a year that you are buying. Do you have a local modeling store or stores you buy from? They must really love you.
17 February, 11:32
Clifford KeeslerThere are no local Hobby Shops around where I live. Sprue Brothers, Scale Hobbyist, know me quite well. I have a group of E-Bay vendors I use quite a lot also. If you ever need aftermarket decals and other goodies check out Rebelalpha and decal supply corps on E-Bay. You can just type in the scale and the aircraft or what ever you are looking for and it will bring up what is for sale. I use E-Bay a lot.
18 February, 01:57
RandoI second eBay, I check it a lot for good deals on aftermarket and kits. Maybe a bad habit lol. The stash talk is funny since I got my first kit in 2021 and I'm only at like 22 planes, and think my stash is huge since I don't have a ton of space. Yet some people have hundreds, it's hard to comprehend. I do collect a lot of aftermarket and conversions for what I have though.
That plane is looking spectacular, it's amazing what a little weathering does! 👌
18 February, 03:18
Jennifer FranklinThank you, Rando. I am relieved that you think it looks okay. I was worried I had overdone the weathering. For some odd reason, I was checking out eBay before I went to unmask my B17. The Canadian site has a lot of US sellers, but their shipping prices are killer.
18 February, 03:29
Jennifer FranklinLMAO, Marcel, yeah, I definitely went for the record on comments with this model. This community has been remarkable in welcoming a new modeler, and I wanted to capture every moment of my build (perhaps a bit overzealous 😛).
18 February, 11:25
Marcel ChmuraYeah the guys are quite enthousiastic. They Just love women modelling. 😂
18 February, 20:07
Jennifer FranklinMy Memphis Belle is finally done. I can't begin to list all her flaws and she definitely leaves room to improve on my future models but you have to start somewhere. I've learned a lot building her. Thank you to everyone who has liked this project and a special thanks for all the constructive advice and encouragement I've received along the way.
19 February, 12:53
Ludvík KružíkEvery beginning is difficult and you have done it perfectly!
Don't look for mistakes in your first model. Enjoy the joy of having built it. Once and for all, it is your FIRST model. And when you come back to it after a while, it will bring back fond memories of your beginnings. 🙂
19 February, 13:22
Bruce HuxtableWow! She's looking splendid 🙂 I have no idea how you have managed not to break any of the gun barrels - I always have trouble with any projecting fragile parts.... The exhaust stains look very convincing 🙂 Congratulations on this very successful creation.
19 February, 13:31
Alec KJennifer, you have do e a splendid job on this Fort. Not an easy build. Looks great 👍
19 February, 14:11
NeilWell it looks fantastic to me Jennifer! No small undertaking for a first crack for sure. Have followed from the start 🙂 Be proud! 👍 What's next!?
19 February, 14:19
Jennifer FranklinThank you, Robert, Ludvik, Bruce, Sebastian, Alec, Duster_d, Neil, and David. @Neil, I am building the "Big Boy" locomotive next. It's in my stash. As soon as I finish my dio for the B-17, I will start a project for it.
19 February, 14:59
Łukasz GlińskiNicely done, great work for a first build 👍
On the other hand I see that making the 72nd kits dirty wasn't tricky only to me at the beginning - my remedy was to play with few new Airfix kits with thier deep lines to improve that, just a food for thought.
19 February, 15:06
Patrick HagelsteinWhoohooh!!! What a 'Belle'!!! Congrats on a beautiful first model! No matter how steep the learning curve, you reached this first bluff in your modeling career. On to the next one! 👍🏼
19 February, 15:24
CaptGPFCongrats on your first build, Jennifer! The work you put into the research and techniques to paint and weather the bird certainly paid dividends! Enjoy the fruits of your labor, you are off to a great start and I look forward to your next build!
19 February, 16:13
Jennifer FranklinThank you, Lukasz, Patrick, Guy, Dick, gorby, and CaptGPF. This is very motivating for my next build. @Lukasz, I am planning on doing a new Airfix kit for my third build, I will keep that in mind.
19 February, 16:19
bughunterNice work especially for the first project 👍
Regarding the stash discussion: do you know scalemates.com/cool-facts.php ? Please look for the Largest stash, but don't be shocked!
19 February, 17:08
Shar DipreeCongrats Jennifer! You put a lot of time and work into your first model. 👍
Did you glue the front dome and top gun turrent (clear parts) with superglue?
19 February, 17:11
Remco van HarenNice work, well done!
Every model is a learning process. So, on to the next one and put into practice what you've learned with this one.
19 February, 17:16
CuajeteJennifer, we always remember our first model and you can feel proud every time you see it on the shelf. You have done a good job.
Congrats!
19 February, 18:47
Jennifer FranklinThank you, John, bughunter, Shar, Remco, Cuajete, and Mark. @bughunter 9648?????? I almost fell out of my chair. @Shar Yes, the top gun turret I glued with super glue and I learned the hard way not to do that again. It was the first clear part I glued.
19 February, 19:39
Michael SchubertDefinitely a finished model that can be displayed with pride! It looks awesome, especially for a first model. The flaws just help us improve next time, but I still make mistakes after 2 decades of building models, so don't focus on them too much or they will take away the fun of building. Looking forward to seeing the dio, and then 'big boy' 👍
19 February, 20:25
Hans-Jürgen Haag😘Nice! Great first Job Jennifer! 👍👍👍 I hopp this is the firs of many😁
19 February, 20:39
James CCongrats Jennifer, you've done bloody well for your first build. Will look forward to see what you decide on doing next. 👍
19 February, 21:12
Jennifer FranklinThank you, Pietro, Ethan, Michael, Hans-Jürgen, and James. For my next two projects, I plan to finish a diorama for the B-17 and then do the Revell "Big Boy" kit. All of this feedback motivates me to get moving on both of them.
19 February, 21:46
Rando DudeI can only agree with everyone else, great work and great result. Especially for a first build it looks really good 👍 😁
19 February, 22:50
Jennifer FranklinThank you, Rando Dude, Nathan, and Skyhiker. I've appreciated all your encouragement along the way as I have built this model.
20 February, 00:56
Mr JamesWell done Jennifer, looks way better after a coat of clear varnish. You can see your weathering at lot clearer now 🙂 As Skyhiker writes, many, many more to go. 🙂
20 February, 01:19
Donald Dickson IIJennifer, fantastic job! It's hard to believe that's your first build. You set the bar high for your next one!
20 February, 01:25
John ECongratulations, Jennifer! I'd have been super happy if my first model turned out as well as yours. You should be very proud.
20 February, 02:37
Jennifer FranklinThank you, Mr James, Donald, Landlubber Mike, Mona, John, and Lost_Erik. This first model's success has a lot of this community to thank. I could not have done it without everyone who commented with helpful instructions above and, of course, YouTube. It has been a lot of fun.
20 February, 11:41
Villiers de VosWell done Jennifer. You are very talented and I hope that mine, which is in the stash, comes out half as good as yours.
20 February, 17:43
Clifford KeeslerOutstanding job Jennifer, you can be very proud of your first model. Well done.
20 February, 21:00
Ralf TopetersThis thread really went through the roof and with every right to do so. This was such an entertaining build. You achieved a really great first model! Especially when you look at the size of it, despite it being smallscale. I never would have dared to pick such a huge one for my first. Now I'm excited to see it in the dio. Carry on your work and you will shine!!! 👍 👍
21 February, 15:03
Donald Dickson III think you may have set the record for longest build thread! LOL
21 February, 15:13
Antoine MeylanBravo! belle réalisation pour un 1er modèle. Félicitation! Continue comme ça!
21 February, 16:46
Moreno BaruffiniIt's seems that I'm one of the few that haven't left a comment! What can I add? I hope that you'll be able to continue in this beautiful hobby and enjoy your first and beautiful model!
I'm also happy to contribute to the record for the longest build thread 😁
21 February, 17:07
CuajeteI forgot to add my like to this album... It would be good to contribute in case it also becomes a record for likes on an SM album 😛
Congrats again, Jennifer!
21 February, 19:45
Jennifer FranklinThank you, Villiers de Vos, David, Kenneth, Clifford, Vincent, Aman, Gary, Andy, DV888ster, Ralf, Donald, Antoine, Moreno, and Cuajete. I bought a 3D printer, and it arrived yesterday morning. I have been busy printing drawers (or trying to) to organize my modeling supplies. So much fun!
22 February, 03:11
Michael SchubertWoohoo!! 3d printers add a lot of fun I find, what model did you end up getting?
22 February, 08:20
Jennifer FranklinThey went on sale so I picked up a Bambu Labs P1P. Long term I plan to get a resin printer as well.
22 February, 11:43
Clifford KeeslerI would love to get a 3D printer, but that will never happen. Lol. I do not quite understand how they work. Do they actually print out a part in plastic, and what do you use as a master?
22 February, 18:04
Jennifer FranklinHi Clifford, yes, they print out parts in various materials. The most common material is PLA, which is a corn product. The master is an STL file, which is a computer 3D file that you can produce using various software packages; it is effectively a 3D drawing.
22 February, 19:22
Clifford KeeslerSounds neat. So you can print any aircraft part you can find a file for.
22 February, 23:05
Dick@Clifford Keesler: I have a few pictures from a 3D printing process in my '1:72 3D printed NASA Sofia Boeing 747SP' thread:
1:72 Boeing 747SP NASA 'SOFIA' | Album by Wolfhound32 (1:72)
Warning.. 3D printing is addictive for scale modelers, because suddenly almost everything you always wanted for a model is printable 😉
22 February, 23:31
Carlos ProençaJennifer, I'm following the Masters of the Air series, and your work is perfect. Congratulations.
24 February, 18:55
Jennifer FranklinThank you, Carlos. Yeah, I sent Nigel photos of my work to thank him for all the good tips he gives, which have helped me improve the quality of my work, and I was pleasantly surprised when he showed my work in his sixth video of the series.
24 February, 19:18
Clifford KeeslerNigel is a really nice guy, and his tips are really helpful. I love his series on the B-52, and if I ever get rich I will most surely use his advice when I get me a decent B-52 kit.
26 February, 01:21
StuartWell done Jen, what a great achievement. I love it more because I am really enjoying watching Masters of the Air at the moment with the Flying Fortress B17F planes and it has inspired me to build one also.
Great work, keep it up and keep enjoying it!
2 March, 00:54
StuartOh by the way just scrolling through your feed and saw you grabbed yourself a Bambu lab printer. Good for you and happy printing. You will go crazy for the first few months then you will slow down to a much more acceptable amount of prints. 😂🤣😂
2 March, 00:59
Jennifer FranklinThank you, Stuart, I hope you enjoy your B17F build. Yes, I am printing almost non-stop at the moment, but I expect that to slow down eventually. 😂
2 March, 04:46
MunkyslutAhh that's come out fantastic! Luv the underside detailing, bomb bay & landing gear & engine pod weathering are all first class💯
Some achievement for a first build!
2 March, 11:16
coporadoGreat build, Jennifer! Love the weathering and painting. Fully second Neuling that is a really great start into our fantastic hobby. excited about your next projects 🙂
2 March, 11:24
Jennifer FranklinThank you, Munkyslut, corporado, and Juskifo. @Juskifo, for my next build I plan to do the Revel Big Boy 1:87 model that I have in my stash.
3 March, 11:47
Clifford KeeslerShe is still a good sized bird, even in 1/72 scale. Still waiting for my Hobby shop to get that one back in stock, all they have right now is the "G" model, which I want also. I am thinking of doing my 1/48 one after the Sky Raider. I am going to do it as Picaidally Lilly from the movie 12 O clock High. Gen. Savage's bird.
4 March, 01:18
Tom HarrisOUTSTANDING, Jennifer! Hard to believe this your first build. Even better that you found enjoyment in the process/education. 😄
Looking forward to the diorama and your next kit!
12 March, 14:18
Jennifer FranklinDavid, I want to finish my dio for Memphis (as soon as I finish the 3D printer project I am in the middle of), and then I plan to do the "Big Boy" train. Thank you, Alexander and Sergej!
18 September, 17:08
Clifford KeeslerI do not remember if I told you how beautiful that bird turned out to be, if I did not I am now. Beautiful job Jennifer, a real beauty.
2 19 September, 01:01
Michael KohlBuiling a model is one thing. But - at least in my eyes - only a vignette or diorama truely brings it to life. You took on a bold project - and you delivered. I am quite shure you will like this machines of yours even with 50 more kits under your belt. Very well done. Something to be proud of.
1 15 December, 17:46
SkyhikerI was wondering if you were going to finish this project just the other day. Happy to see it in completion. The cows are a nice touch. Congratulations.
1 15 December, 17:52
Jennifer FranklinThank you, Michael, Skyhiker, and Clifford. Each of you taking the time to give me feedback is appreciated. Part of what motivated me to keep going through the whole build was all of you.
16 December, 14:01
SkyhikerYour very first dust collector... Err... I mean diorama. Hopefully you can find a good place for it.
1 16 December, 15:52
Jennifer FranklinThank you, CaptGPF and Skyhiker. It was my sister who asked for the cows, and that is the main reason I spent 60 dollars on them. They were a little pricey, but they turned out nicely. I have the model stored in an almost airtight container, so hopefully, it won't collect too much dust; time will tell.
2 16 December, 17:50
Jennifer FranklinThank Rui and Nathan. It feels good to have finished my first project finally.
16 December, 23:38
MS Kдобави нов фотоалбум.
54 снимки
Peugeot 306 Maxi & Evo2 - WIP
1:24
Because of the paint properties, the decals were sticky and difficult to position even before they were applied.
Even wo...
Проект: Peugeot 306 Maxi & Evo2
3+ 23 5 December, 22:19
Spanjaardi will seat behind Martin then 😄
i would have never thought of bending stuff in the dishwasher, good idea!
6 December, 13:03
Michael Kohl"If there's trouble from the beginning like this, there are often troubles throughout the work,..."
Well, one way to look at it. I'd rather say: whatever problem might come along, you will find a way to fix it.
I am in for the ride.
6 December, 22:07
MS KThanks Michael. Another trouble has occurred again. but your words are encouraging. I'll try to finish it this year if possible. 😄
7 December, 13:26
MS K@Denis Dogadov - Because I want to have both versions.
0:54, 13:55 Attached Ext light.
Youtube Video
1 9 December, 15:47
Denis DogadovThe problem is that this removable unit will scratch the paint on the hood every time you take it off, a bad idea.
9 December, 15:51
MS Kmotorart.tistory.com/465
Oh, I've used magnets occasionally, but I've never scratched it yet. Thank you for your advise. 😉
9 December, 15:58
Martin OostromIt looks like you went too wet on the white. A shame as you were progressing so quickly
9 December, 16:04
Sy Barдобави нов фотоалбум.
7 снимки
Panzerkampfwagen I Ausf.B (Sd. Kfz.101) 
1:35
First kit part victim of the carpet monster - jack handle, copper wire to the rescue
1 15 December, 21:35
Mina RoHey guys, I am curious to hear what peoples methods are of painting metal barrels or photoetch parts. I did my first metal barrel tank kit a few months ago with a T-62 and an Aber 115mm barrel. I noticed that the paint I airbrushed onto it got nicks in it very easily using acrylic just with minimal handling. I got better results by laying down a coat of laquer paint as opposed to acrylic and then a coat of clear varnish. Anyone else do differently?
16 December, 19:38
Urban GardiniI suggest that you first paint metal parts with a metal primer that sort of etches itself to the surface of the metal and thus give the water based paints better adhesion! Both Tammy and Mr Hobby have metal primer, I use the Mr Hobby primer.
mr-hobby.com/en/product2/category_33/1873.html
super-hobby.se/produ..Primer-33273408.html
1 16 December, 19:45
Kesa TihoPrimer works well. Especially tamiya. I haven't used it with airbrush but it completely ruined my brush, so be careful with it.
1 16 December, 20:17
Mina RoThanks, I do use AK primer paint but I will get some mr hobby primer to see how that works. Thanks! I used to use tamiya fine primer in the can which is great stuff but I have since gotten away from rattle cans and am enjoying more airbrushing.
16 December, 21:19
Urban GardiniI forgot to say that I brush paint the metal primer direct on the PE and turned barrels and such. I saves primer and you only get it on the metal parts. Otherwise I prime with Mr Surfacer through the airbrush.
@Kesa that depends on the seals in your airbrush. Most airbrushes from the reputable companies have PTFE seals that can withstand heavier stuff that makes you see pink elephants flying in your studio if you don't ventilate as you should, ie the good stuff...
16 December, 23:12
Chris Parsonsдобави нов фотоалбум.
12 16 December, 03:12
Michael KohlI can only add to the praise. I'd love to read a word or two on you in-build impressions. Me thinks that you did some serious finetuning, aftermarket and detailling.
16 December, 09:10
Chris ParsonsThanks very much mates, this one took a bit of work to get across the finish line! I can confirm the struggle and the only component of the model not modified, converted, changed or, replaced was the cockpit floor and instrument panel, those two pieces are as is from the kit. The fuselage was lengthened, reprofiled nose and tail, replaced all the cabin windows, modified the cockpit windows, added span and chord to the main planes, span to the tail planes, bullet fairing on the vertical fin, new landing gear, new engines new props/ spinners and on and on and on.
I previously completed a DHC-8 300 so thought this would be….doable, well it was but almost not.
All I need now is another -8 kit to do the 100 as is from the box
Thanks again to all who liked and replied!
Very encouraging folks here
1 16 December, 23:05
Ben Sдобави нов фотоалбум.
17 13 November, 20:30
John MulhallLooks great Ben. How did you like working with the Model Alliance (MA) decals? I have some MA decals that I am planning on using in my current project, any tips to pass on?
2 December, 23:48
Ben SThanks John. They're pretty good, maybe a bit thick but at least that means you can handle them easily. I also thought the white areas were a little transparent, but actually on the model it looks fine.
I wet the area with Micro Set before placing them then gently removed as much liquid as I could with a cotton bud and gave it a few coats of Micro Sol - they puckered up a lot, especially the wing roundels, but settled down as they dried.
3 December, 06:39
John MulhallThanks Ben, that is an excellent tip. Wishing you best of success and enjoyment as you finish out your Beaufighter.
3 December, 12:28
Jean Tchaoдобави нов фотоалбум.
15 15 December, 14:37
Jean TchaoThanks to all ! as Chaos is mentioned it was real chaos on my desk during this project so many hours I spent to reshape all figurines in order to have different poses ! 🙂
15 December, 20:16
Melgreat detailed work, i particularly like the painting of the shields and armor
16 December, 22:18
Alec Kдобави нов фотоалбум.
78 16 February 2021, 02:10
bughunterYou are obviously heavily infected, but not with Covid19, but AMS😉
Watching!
16 February 2021, 13:45
Greg BakerOh... this is brave. I've built a couple of these before. They're fun, but they definitely need a lot of love and attention.
16 February 2021, 15:53
Alec KGreg, I totally remember your project (AREA 88 - F4F-4 "Boris" | Album by strobez (1:72)). You did a great job with the interior. And of course, build two... I had a weird relationship with this kit. Had it up for sale quite some time (sold the Eduard PE set and Squadron canopy for it few years ago. Dumb). It took Mssr Glinski's gentle kick to get me going on it. It's fun so far 👍
Lukasz' parallel build is here: USN Wildcat | Album by Woody (1:72)
16 February 2021, 17:24
Greg BakerOh, I remember the wheel wells being a real challenge... all those sticks going everywhere! I can't wait to see how yours turns out.
17 February 2021, 03:20
Petr LehnertI have done an Academy Wildcat with Aires cockpit, it was horrible experience. So I wish you good luck with that, you seem to have more experience with such undertaking. I have some photos of the build mixed together in my Hasegawa Wildcat album (it was double build and I still have not moved the photos to separate project).
17 February 2021, 18:48
Alec KThanks Petře. Good to know I am not alone in my madness. It's actually coming along pretty well. The trickiest thing will be the section behind the instrument panel. Cheers 👍
Matthew - luckily the fuselage accident was a clean break, it will glue back up nicely (fingers crossed).
18 February 2021, 01:50
Łukasz GlińskiThat's a serious build, mine will look like HB kit when parked aside😉
20 February 2021, 19:52
Alec KWelcome Cuajete.
Lukasz, I have an unfortunate tendency of making things more complicated than they need to be 😭
How is your build progressing?
20 February 2021, 20:16
Łukasz GlińskiI closed the canopy today (y'all can start booing now!) after trying to imitate the gunsight (had to glue it the canopy in the end). Lost the pilot stick in the process (Long live the Carpet Monster!). Main gear assembly is pending right now 🙂
20 February 2021, 20:30
Alec KToo bad about that stick, but I don't think you will see much through that canopy.
That landing gear is quite the monstrosity! Greg was right... good luck 👍
20 February 2021, 21:42
Petr LehnertYou made a terrific job fitting the cockpit inside! Klobouk dolů!
22 February 2021, 11:09
Alec KDíky. It was actually relatively easy to do. The dashboard section will be interesting…
22 February 2021, 13:50
Slavo HazuchaAires will not settle at delivering some of the best looking resin around, they also embarked on the mission of making us better modelers and learning new skills & inventive methods when we actually want to fit their parts on our models... 🙂
Excellent work - just hope the final model layout will allow a peek at the fruits of all these efforts! 👍
23 February 2021, 19:24
Alec KThanks Gorb, welcome to the show!
Welcome Slavo. You are right about Aires. Adapting their Hasegawa cockpit to the Academy kit is actually going pretty well. Their engine is fitting even better. And yes, very little of it will be visible in the end...
24 February 2021, 02:16
Alec KGot the cockpit assembly pretty much wrapped up. Pretty happy with how it turned out. On to the wheel well and landing gear😎
27 February 2021, 19:19
Łukasz GlińskiHm, that's where the Airwaves set was wrong, the desktop should be far more backwards than they suggest 🙁
Thx for the window tip, I have to sand them.
27 February 2021, 19:36
Greg BakerDon't worry, Alec, you'll know what's in there... and you'll have the pics to prove it!
28 February 2021, 07:29
Łukasz GlińskiAlec have you already investigated the drop tanks? Or are you going to skip them? I offered one of the Airwaves supports to the Carpet Monster and wonder how to scratch something at least a bit convincing 🙁
5 March 2021, 15:30
Alec KThanks Guillaume. It worked our pretty well.
Lukasz: I do have some references for the drop tanks. I'll send you a PM.
5 March 2021, 20:16
Alec KThanks Frank! Moved the project along a bit and have most of the interior done, ready for paint.
13 March 2021, 23:44
bughunterAfter the new update I would like to press the Like button a second and third time!
13 March 2021, 23:55
gorbyWell that's a bit stunning!
I had to check the scale again as I was starting to wonder if you're working on 1/32 scale kits now. 😮
23 March 2021, 15:12
Łukasz GlińskiYou should leave the fuselage cut in half, otherwise all that excellent detailing will be lost 🙁
23 March 2021, 15:26
Alec KThanks guys for the kind words. I am having fun with this one, although the kit is definitely past today's standards. A great bench for trying new things 👍
24 March 2021, 14:34
Alec KGot some time at the bench and managed to close up the fuselage and add the wings. Cheers.
17 April 2021, 00:30
Łukasz GlińskiAh, the saga continues 👍 The amount of detail you add makes me blush 😄
17 April 2021, 09:12
CuajeteWow... Sure that is Academy's kit or the next Arma Hobby one? 😛
Great job so far, Alec! 👍
17 April 2021, 09:47
Alec KThanks guys. Lukasz, I am a bit embarrassed how long it's taking me to get this one done. But the detailing is my favorite part, so I just go with it.
Thanks Cuajete. I was actually going to wait for the Arma kit, but then Lukasz got me all riled up on this build and well, here we are... 😄
17 April 2021, 11:23
Łukasz GlińskiOnce they (AH) release F4F-4 version (so I can build the FAA striped one) we can repeat this GB 😛
PS. My fav part is the stash expansion 😄
17 April 2021, 11:43
Alec KThanks gents. I got the canopy work done and have 'er primed. Gearing up for painting 👍.
24 April 2021, 15:48
gorbyWOW! Stunning work Alec.
I haven't had the chance to check on your progress for a while and I'm absolutely flabbergasted by the detail you're achieving.
It's made for a very interesting and educational morning catching up.
6 May 2021, 06:01
Daniel KlinkAmazing stuff Alec?
You made more than a lot out ofthis rather basic elder kit?
6 May 2021, 06:27
bughunterWhat a great build with a huge amount of care in every little step! You can see that in the result! 👍
6 May 2021, 11:51
Alec KThank very much for the kind works guys. It took me waaaay too long to get this "quick" build done, but I just could not build it OB. The shape of this kit is just not right (fuselage) but it looks ok. Cheers!
6 May 2021, 12:23
Alec KHello mates! Finally got around to shoot the complete model, here is the gallery album: Grumman F4F-4 Wildcat gallery | Album by Pardubak (1:72)
28 May 2021, 02:38
Guillaume BlanchetYour dedication on this project rerally paid off. Amazing result ??
28 May 2021, 11:29
Edward MacKenzieOMG, a lot of work! But it's worth of it. Congrats, the result is amazing!
29 May 2021, 10:22
Petr LehnertFantastic result. Send the pictures to Academy, so they can show on the next boxing how finished model looks like.
31 May 2021, 19:46
Alexander GrivonevYou didn't just go the extra mile, you ran a complete friggin marathon! Awesome effort, love honest craftsmanship, dedication and a no compromise approach 👍
31 May 2021, 20:42
Alec KGuys, thanks very much for all the kudos. I no longer feel bad putting that much effort into an old kit, particularly one I slated for stash ejection 😛
1 June 2021, 11:51
JohnI thought it was a 1:48 scale kit at first - top notch work and details. Thanks for taking the time to provide additional information of the build in your photos, it is much appreciated.
19 July 2021, 01:07
Alec KThanks a lot guys!
John, glad you liked my build log ramblings. Welcome back to the hobby, and to Scalemates 👍
19 July 2021, 13:19
David R. MeizosoFew posts are so inspiring, thanks for sharing such amazing skills. Enhorabuena!
19 July 2021, 18:17
Damian GüttnerExcellent work !!! Conjure up such a result from this old kit, with so many modifications! Super.
I also built the kit over 20 years ago, of course not in such top condition.
The only criticism point: the position lights
19 July 2021, 19:21
Alec KThanks very much, I appreciate it. It keeps my modeling mojo going 🙂 Damian, you are right about those position lings, I have to get better at those.
20 July 2021, 00:28
Slavo HazuchaWent some way since I last checked and it's just splendour all around - can't comment much on correctness of Wildcat details, but the whole job looks awesome, great detail & paintjob all around, really like the yellow outline stars too 👍
7 August 2021, 19:09
Bernhard SchrockVery stunning result by using this old kit (I know this also)!!
8 August 2021, 13:44
JohnYour tip on photo 97 is very smart - I have had glue creep up on several sliding canopies.
8 August 2021, 15:03
Daniel KlinkMore than well deserved Alec for that effort and that stunning result with this old rather mediocre kit as base 👍
8 August 2021, 18:09
RuiThis album took me more than a hour to ro through. I read ever caption, sometimes twice, and studied every image carefully. It was so entertaining and I learned so much. Amazing work. Thanks 👍🏻
30 October 2021, 04:43
Celliersдобави нов фотоалбум.
31 снимки
Lockheed F-80C Shooting Star
1:72
Decals sealed with a mat coat to take a bit of the shine off.
Проект: Lockheed F-80C
34 31 October, 16:30
Gary VictoryReally nice work on classic....i remember building this kit back in '80's. Looking forward to see your progress.
5 November, 07:12
CelliersThanks for all the comments.
@B. M. - I used Mr Dissolved Putty for the gaps.
7 December, 17:24
Michael KohlYeah, 20 pieces do not automatically turn into a quick build. 😉.
Great job. You lifted that ancient kit to an entirely different level.
2 8 December, 08:27
Kesa Tihoдобави нов фотоалбум.
28 снимки
Operation Cabrit in Kohtla-Nõmme :D
1:72
Added: snow onto the soldiers boots, marks left behind by the challenger, snow flakes onto the challenger and engine gri...
1+ 12 23 November, 13:00
Kesa TihoOoooh it is, either im gonna fuck up real bad or make a meh dio. Either way its gonna look like the skies of Berlin during mid 1945, a spectacular firework show of destruction and 88 Flak
5 December, 16:12
Kesa TihoAlright so i dont usually make comments to update people on progress but i cant be bothered to fight with my browser right now
So i got my fathers military notebook/guide and now i can place the troops more realistically, yay.
Got the 50€ from my grandfather so thats a win. Gonna go to the model store the first chance i get on monday.
Also busted my knee because i drove into a telephone pole whilst going like 20 km/h on my bike because some random woman saw and stepped where i was riding, so that might limit how fast i can make the dio.
8 December, 10:33
gorbyHope your knee gets better soon. The good news is that in the meantime you can rest your knee by doing more modelling. 🙂
2 8 December, 15:53
Kesa TihoBroken arm? Scale modelling. Fractured ankle? Scale modelling. Asthma? Scale modelling. Cataracts? Scale modelling.
Your truly a genius mate 😂
Also, thanks
1 8 December, 16:01
gorbyNice progress Kesa.
If you can it would probably be better to avoid Vallejo model air as it's intended for airbrushes as far as I know. I think it's 'Vallejo Model Color' which is for brush painting.
13 December, 07:15
Kesa TihoModel air is for airbrushes but I bought it since only model air had the right tone of Russian green I needed for my T-90A turret bunker. And since I didn't have enough of any other green I decided to use this. Plus it looks close enough.
1 13 December, 08:00
Jennifer FranklinIs it a coincidence that you are doing a winter scene as the winter holidays near? It's looking good so far. I love the imagination that went into this one. I hope your knee heals well; that sounds painful.
1 15 December, 11:24
Kesa TihoJennifer: It is a bit of a coincidence, but also since i mainly think of Kohtla-Nõmme in a winter scene since I've spent most of my time there during winter and because im just sick of making grass. As for the imagination, there wasn't much, since i took the idea from another build i saw on here. I only added troops and a place ive known for 12 years.
gorby: probably because I used pre made snow, along with some brush cleaning water which gives it a subtle dirty look.
1 15 December, 11:44
Duncan Blackдобави нов фотоалбум.
6 29 November, 11:04
Walter Ghiselliдобави нов фотоалбум.
3 29 September, 21:18
Mr DLike it 👍 best colour scheme, I'm building an su-30 at min and will do similar colours.
.see you like the Soviet 🚩stuff too
14 December, 00:29
Walter GhiselliSi, me gustan los diseños que hacen los rusos, aunque no son muy discretos
16 December, 21:49
Bogicevic Vladimirдобави нов фотоалбум.
6 8 April 2020, 21:20
Bogicevic VladimirI can recommend it. Everything fits and all you need is in the box. Thank you for comment.
10 April 2020, 16:13
walarooдобави нов фотоалбум.
12 2 December, 19:39
/bg/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=bg
35
35
/bg/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo