Новини

Martin Oostrom
Another ghost build that started in my vacation. All parts are ready for paint, unfortunately the weather isn't cooperating.

Alexander Grivonev
What's with the weather in your corner of the world😄
too warm?

Martin Oostrom
Too windy and wet. I can't open my window to let the hose from my spray booth out. Rain will come in 🌧️

Martin Oostrom
Wind from another direction today, so primer is on.

Martin Oostrom
Painted with Zero paints Jordan yellow. Needs another coat or two

Michael Kohl
Following.
PS: you can guide your hose into a bucket with a bit of water and a lid with an airvent.
Check: How to use a bucket to vent a spray booth on Youtube. I will build myself one too as the concept looks very convincing.

Spanjaard
nice yellow color!

Ben M
👀

Martin Oostrom
The yellow needed 7 more thin coats. More than half a jar was used on this small car.

Ben M
That's yellow for you!

yngvenett
Following this

Alexander Grivonev
Hey Martin, you can buy colored primers like yellow or red. 2K as well.

Martin Oostrom
Thank you gents.
I have black, yellow, white, pink, three kinds of grey and rustoxide red primer. But the zero paints yellow "needs" 2k and that is one of my greys. That paint is soooo thin with colour. The decanted ts-16 on my Aussie truck covers so much better.

Martin Oostrom
Assembly has started. Most has been done. Now the body needs clear coating.

Ben M
Yellow looks great.

Dominik Weitzer
cool cool cool 🙂

Spanjaard
Looking good, i hope decals are working as expected

Snake Plissken
Wow, chrome plated!

Ben M
Taking it on vacation with me to get it started.

Nathan Dempsey
Bearcats unite! Following 👀

Guy Rump
Following. 👍

Snake Plissken
Is it similar to a commemorative edition or just meant to replicate natural metal finish?

Ben M
It's aluminum plated to represent the actual nmf finish. I built a t-33 where I had some issues that I hope to improve upon.

Ben M
Did a lot of sanding areas that will be glued, masking, fitting parts to each other, and basic assembly while I'm on vacation. I got new decals from Siam decals as the originals are from 1968 and not in good shape. I'm not sure how old the Siam decals are but they are newer than '68. One thing that is apparent is the stripey tail decal doesn't fit at all. This is going to be a good challenge to resolve.

Robert Podkoński
Taking a seat here.

Ben M
Decided to try to apply the 1960s decal for the cockpit, as I don't have an alternative. Had to soak it for about a minute in hot water to get it to release. As is typical for hawk kits the decal isn't the right size but you go to war with the decals you have. I got it to apply without shattering. Unsure if it will stick, very old decals like this often have to be glued in place.

Neil
Interesting 🤔 following also, looking good 👍

Ben M
I think the Siam Scale decals I'm using instead of the originals are about 20 years old but they're going on ok. A little thick, so not settling down into panel lines but I'll try some decal fluid once they set in place, hopefully they will on the aluminum surface! The roundels are two part so I will have to do a second layer…

Mr D
Smart little model.... unusual in the factory chrome 👍👍
Nice classic kit.
Bit of heat of hairdryer works with thick decals.... nice n steady.
Like it 😁👍

Ben M
That's a good idea, I may give it a try. First I'm going to upgrade from micro sol to mark fit.

Mr D
I use Mark fit ....but recently found the Vallejo one works amazing... Just used it on my in progress IAR-80.
Definitely my go to now.
The moon ships is great 👍👍

Nathan Dempsey
Wow Ben this one is turning into a colorful bird.

Ben M
An interesting detail I note while decaling. The panel lines on the fuselage are engraved. The panel lines on the wings are raised. Wtf.

Desert Marlin
I've been using Mr. Mark Softener and Mr. Mark Setter. They worked well on some Kitty Hawk decals which are pretty stubborn...

gorby
Nice work so far.

Ben M
The tamiya mark fit and some work with a needle solved the problems! Thanks for all the great ideas everyone. Onwards!

Ben M
Did a bunch of cut the decals into pieces to fit a different model than they were made for. Came out fairly well. Subassemblies are getting larger as the project comes together.

Dave
Looks great. Nice work

Desert Marlin
You seem to have forced the decals to cooperate!

Robert Podkoński
Great job, Ben!

Mr D
It's looking really good 👍
It's great that the kits can still be built after all these years.
The people in the factory's would have never believed the model they are packing wouldn't be built until 2024 🤔🤣.
Nice build to follow 😃

Ben M
Almost complete. Popped the main fuselage seam a bit 🙁 I had gone to a lot of work to hide it. For some reason even after carefully scraping the mating surfaces I just don't get good adhesion. Maybe next time I will try only using CA for assembly on my next plated kit.