Новини

Ian Doody
Made a start on the 1/32 Trumpeter F4F-4 Wildcat, I'm having my wings permanently folded, this is just all dry fitted so far, I'll add more detail later when the wing is added. No point cleaning up the inside part of the wing of ejection holes, as this will be hidden behind the wing. Think it looks ok so far.

Ian Doody
So today I've semi painted up the other sides wing root fold system. And started dry fitting the engine. Need to pick a scheme from the Techmod decals at some point, thinking of 1 or 4 so far.

Ian Doody
Ooh landing gear and engine support structure. Just needs a few touchups, thats it done for now, have to glue it all up straight away, doing it later would be a pain in the ass. Looks ok, I'm no expert on these things. Just for fun build in-between other stuff.

Ian Doody
I think, as an engine that'll do really, don't need anymore detail on it. Couldn't see it if it was there anyway. I'll paint the rear bank of cylinders, but that's probably it.

Ian Doody
That's all for today, making the most of what you get in the kit, only added bits of wire, no sense going mad with detailing parts you wont see. Prop tomorrow, finish the rear bank of Cylinders, and make a start on the cockpit. Looking nice so far, looks like an engine to me.

Ian Doody
Engine, exhaust manifold system and front bulkhead done. For what you can see, the kit parts are good enough. No point spending lots of money on a resin engine. Just some wire and a bit of paint.

Rui S
Looking special 👍 I'm in 😎

Guy Rump
Looking good and detailed build notes, following. 👍

Ian Doody
That's it for today, don't think I can handle seatbelts as well. So far so good, looks like a cockpit, when it's in the plane, you won't see anything. I tarted up the kit seat, as I couldn't stomach making the PE eduard one.

Rui S
hum, hum 😎 looking good 👍

Ian Doody
So I can do seat belts, but I hate doing seatbelts, not brilliant, but for all you'll see, it'll do me. My fear of PE is lessening, I'm getting a bit more confident each time, next the top straps. Then I can tackle the joining of the fuselage halves together, which is tricky on the 1/32 Trumpeter F4F-4 Wildcat, as a few parts need extra sanding to fit. Looks ok to me so far.

Ian Doody
Seatbelts done, that'll do. With my eyesight it'll look amazing from far away lol 😆 but for me, as a learning exercise, looks fine. I would wholeheartedly recommend HGW Laser seatbelts, they make it a lot easier.

Ian Doody
Tomorrow I'll make a start on the Empennage and getting everything to fit. I'm not using any of the PE hinges either. Then wings.

J35J
Great work and progress so far!👍🏻

Nicolas
Following

Freak
Wow, beautiful shading!!

CaptGPF
Agree with Freak

Bruce Huxtable
Watching in anticipation of the final unveiling 🙂

Robert Podkoński
Watching with interest.

Vincent
This looks great. I really like the scheme!!!

Thomas Kolb
That weathering looks awesome. What technique did you use? Just oil paints?

Finn
Following

Maciej Bellos
Beautiful!

Cuajete
Very nice painting job and weathering 👍. I have the same question that Thomas.

Tzonglin Wu
Thank you all for your likes.
For me, this time is also an experiment. It's my first time to build a kit like this way.
I'm looking for a quick way to save time while I'm busy at work.
This time I didn't use primer or do pre-shading.
I airbrushed whole fuselage with the main color.
Then refer to photos, hand brushed the darker and lighter colors to create difference.
I think this make the shade effect.
Until this process, only water-based acrylic paint had been used.
In the #13~#15 pictures shown, I have used Mr. Weathering's black to create the panel line.
Yesterday, I covered the plane with mat varnish, I found that the contrast became smaller.
I think I should increase the contrast before the mat varnish in the future.
My weathering process is not over yet.
Oil paints, color pencils, etc. may be used to enhance the effect.

Cuajete
Thank you so much, Tzonglin Wu 👍

gorby
Nice work.

Peter Mollenhauer
Thx Gorby! 🙂

Robert Podkoński
Nice indeed.

Peter Mollenhauer
Thx Robert! 🙂

Alex K
Taking my usual seat...

Nicolas
Taking a seat next to Alex.

Ben M
🪑

J35J
Joining!

Ben M
It's looking great!

Nicolas
Good looking plane.

Duster_d
I'm starting to get a little nervous about those NOVO/FROG biplanes that are in my stash. If their racks are cast in the same crooked way, then the buildings promise to be "interesting". 🙂

Nicolas
Hey, great result. 👍 I'm allways worried about biplanes, but that's perhaps cause the only Biplane I build so far from a tool that wasn't from th 60s was from Amodel.

J35J
Great work👍🏻