Kinetic F/A-18A+/B / CF-188 - Build

1
April 18, 2021
2
April 18, 2021
3
April 18, 2021
4
May 8, 2021
The intake part is a bit tricky
5
May 8, 2021
6
May 8, 2021
Also the fit of the top and bottom part is rather mediocre
7
May 8, 2021
That's the area where the internal spacers would be needed...
8
May 16, 2021
Do those three things to be glued on like this? I'm a bit confused...
9
May 16, 2021
10
June 18, 2021
11
August 18, 2021
12
August 18, 2021
13
August 18, 2021
14
August 18, 2021
15
August 28, 2021
Really nice decals to work with! The downside : there are some missing...
16
August 28, 2021
17
September 6, 2021
And as always, there's one decal which didn't go as planned...
18
September 6, 2021
But his side looks awesome!
19
September 6, 2021
Agan a bit of a rough surface, it still happens to me once in a while…
20
September 6, 2021
21
September 6, 2021
22
September 28, 2021
All decals added to the fuselage and some parts already received a bit of weathering.
23
September 28, 2021
24
October 5, 2021
Hmm, not sure if this is going to look good in the end...
25
October 14, 2021
After the wash the initial weathering looks a bit better
26
October 14, 2021
27
October 14, 2021
Finally things come together
28
October 19, 2021
Arghh, i still don‘t like the weathering. But i think there‘s not that much i can do anymore. Maybe the matte/satin finish tones it down a bit, we will see.
29
October 19, 2021
Front LG looks ok to me
30
October 19, 2021
Also main LG is ok, don‘t know if it really has the red on the doors, but i liked it as it gives a bit of color…
31
October 19, 2021
Does anybody know where this needs to be fitted? I can‘t figure it out in the instructions (which are really lousy…)
32
October 23, 2021
33
October 23, 2021
Undortunately there's some fogging on the canopy... I need to get a bit creative...
34
October 23, 2021
35
October 23, 2021
36
October 23, 2021
Nearing completion...
37
October 25, 2021
It's basically done, just need to deal with the canopy...
38
October 25, 2021
39
October 27, 2021
A bit of damage control on the canopy
40
October 27, 2021
41
October 27, 2021
42
October 27, 2021
A job done! 🙂

Коментари

35 18 April 2021, 10:30

Daniel
Nice subject! ?
Typical kinetic kit but its the best we've got for the legacy hornet?‍♂️. There are some workarounds to be found in forums, e.g. internal spacers/sidewalls for the rear part.
Watching!

8 May 2021, 17:32

Alexander
Also taking a seat, looks quite good so far, like the detail paintwork in the landing gear area as well as in the cockpit. 👍

18 June 2021, 22:09

Schnemat
a bit of progress here, everything is now painted (even though i think i didn't hit the color tone very good, hopefully weathering improves that...) and there is one correction needed as the paint peeled in one spot.

18 August 2021, 10:11

Clifford Keesler
Looking good.

29 September 2021, 00:47

Jos Jansen
Nice progress Schnemat...!

29 September 2021, 13:26

Eric Thornton
Oh 410 Cougars training squadron. Same one I want to build. Looking great!

15 October 2021, 07:58

Schnemat
I like double-seaters, so that was the one to go with the kinetic kit 😉

15 October 2021, 09:56

Alexander
Great work Schnemat, really like the outcome so far! 👍
As to your question about the pod, I think it goes on the left side fuselage anchoring normally reserved for the air-to-air missiles - at least this is the case for the Rhino Hornet.

23 October 2021, 01:10

tyu
[img1]

23 October 2021, 10:54

Daniel
Pic 32 shows you're already using the correct pod in the correct position 👍
(pic 31 shows the litening pods that preferably goes centerline position on most non-navy hornets - but also not used by RCAF)
a great looking hornet, I really like the typical streaks behind the slats, looking forward to the big rollout! 👍

23 October 2021, 13:00

Schnemat
Thank you for all your nice comments! I hope the canopy is not going to ruin the whole model...

23 October 2021, 14:55