Novinky
Peter Muldoon
přidal nové fotoalbum.
přidal nové fotoalbum.
35 obrázky
2016 Corvette StingrayNový: 29 July, 00:15 1:25
Body in SMS Blue Angels Yellow.
Projekt: 2016 Corvette Stringray
15 16 May, 10:03
Peter Muldoon
Thank you Martin! A little out of practice, but enjoying the process. Just happy to be modelling again really.
Thank you Martin! A little out of practice, but enjoying the process. Just happy to be modelling again really.
18 May, 09:54
Peter Muldoon
Not intentionally quick, but there isn't too much to this kit so it is going quicker than expected. Good to be back at it.
Not intentionally quick, but there isn't too much to this kit so it is going quicker than expected. Good to be back at it.
21 May, 12:38
Dominik Weitzer
very nice work. like the interieur and the "small" details on the engine. well done so far!
very nice work. like the interieur and the "small" details on the engine. well done so far!
22 May, 15:21
Christian W
Super nice details! I like the brown you've chosen for it. At the end it will look great with the black rims.
Super nice details! I like the brown you've chosen for it. At the end it will look great with the black rims.
27 May, 04:28
Peter Muldoon
Thanks Christian, it's my attempt at a tan, made from a concoction of Tamiya acrylics.
Thanks Christian, it's my attempt at a tan, made from a concoction of Tamiya acrylics.
10 June, 08:47
Stilicho
vlastní tuto položku
vlastní tuto položku
Boeing B-17F/B-17G Flying Fortress Full Colour 3D Seat Cushions (designed to be used with Academy, Airfix, Frog and Revell kits)
Kits-World 1:72
KW3D172006 29 July, 00:11
Gary Norton
přidal nové fotoalbum.
přidal nové fotoalbum.
38 29 January 2023, 14:12
Gary Norton
More interior work, and test fitting, I am a little hesitant to start gluing it because I ordered the brass gear from Aerocraft models and it hasn't shipped yet. I may press on as the nose gear is the only questionable item. the gear assembly is step 2 most of it attaches to the floor that is part of the radio room under the cockpit but one piece attaches to the lower floor forward of the bomb bay, and completes the cockpit/nose gear assembly. I am hoping that those pieces will flex enough to install it later.
More interior work, and test fitting, I am a little hesitant to start gluing it because I ordered the brass gear from Aerocraft models and it hasn't shipped yet. I may press on as the nose gear is the only questionable item. the gear assembly is step 2 most of it attaches to the floor that is part of the radio room under the cockpit but one piece attaches to the lower floor forward of the bomb bay, and completes the cockpit/nose gear assembly. I am hoping that those pieces will flex enough to install it later.
31 January 2023, 22:07
Stilicho
vlastní tuto položku
vlastní tuto položku
Messerschmitt
Bf 109G-10 - Air Intake & Tail Wheel for Revell Quickboost 1:72
QB 72 039 200x Nová forma 29 July, 00:04
Jetdoc
chce tohle
chce tohle
DCLV Eagle Deep-diving Core-ized environment resilient Landing Vehicle
Planet Ring 1:100
2023 Nová forma 29 July, 00:01
Hang Li
přidal nové fotoalbum.
přidal nové fotoalbum.
37 obrázky
1/350 HMS MontroseNový: 28 July, 23:56 1:350
waiting for weathering
Projekt: 1/350 HMS Montrose
15 24 June, 07:48
Thomas Wirsching
Great job so far! I would love to get an explanation about how to do these LED lighting in detail as I have no idea about this.
Great job so far! I would love to get an explanation about how to do these LED lighting in detail as I have no idea about this.
8 July, 05:04
Hang Li
Thanks Tim, Villiers, and Thomas. I did put a led for the trolled sonar bay back at the stern. It is apparently not bright enough to be really visible. Probably not noticeable after finished.
I prefer to use Led tape light as it has build in resistors so I don't need do calculation to figure out the resistor value. Once that is sorted, what left is just connect the led unit with a battery and a switch. I think it is better to ask a trained electrician as the circiut I built don't last long and I don't really know why.
Thanks Tim, Villiers, and Thomas. I did put a led for the trolled sonar bay back at the stern. It is apparently not bright enough to be really visible. Probably not noticeable after finished.
I prefer to use Led tape light as it has build in resistors so I don't need do calculation to figure out the resistor value. Once that is sorted, what left is just connect the led unit with a battery and a switch. I think it is better to ask a trained electrician as the circiut I built don't last long and I don't really know why.
9 July, 12:37
David Hutchinson
chce tohle
chce tohle
The Battle of Britain: Aircrew from Australia Their Aircraft and a Modeller's Guide
Peter Roberts
2024 28 July, 23:55
Dennis Tennant
vlastní tuto položku
vlastní tuto položku
German Heavy Armored Car Sd.Kfz. 234/2 Puma Tamiya Italeri Series
Tamiya 1:48
37010 2011 Nové obtisky 28 July, 23:54
/cs/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=cs
35
35
/cs/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo