Novinky
Marcin Dudek
přidal nové fotoalbum.
přidal nové fotoalbum.
20 15 September, 15:32
Marcin Dudek
A new build starte 🙂. It seems quite easy but one thing puzzles me - the tracks. They compose of 4 straight plastic parts and instruction says to bend them with hair dryer. It is first time I encountered this type of tracks. Anyone tried doing something like this?
A new build starte 🙂. It seems quite easy but one thing puzzles me - the tracks. They compose of 4 straight plastic parts and instruction says to bend them with hair dryer. It is first time I encountered this type of tracks. Anyone tried doing something like this?
15 September, 15:36
Snake Plissken
I have heard of this type of assembly but have never built one. However, I have lots of experience heating and softening styrene plastic. You can also try very hot or boiling water -- soak the tracks in boiling water, then fish them out of the water with long tweezers and bend them around the rear sprocket, idler and road wheels and hold until they cool. You may even get by using no heat, just slowly and carefully bend curves into the tracks.
I have heard of this type of assembly but have never built one. However, I have lots of experience heating and softening styrene plastic. You can also try very hot or boiling water -- soak the tracks in boiling water, then fish them out of the water with long tweezers and bend them around the rear sprocket, idler and road wheels and hold until they cool. You may even get by using no heat, just slowly and carefully bend curves into the tracks.
15 September, 20:46
Marcin Dudek
After some work done I need to say I am a little disappointed with this kit. Instruction includes some mistakes and it is not always easy to read how and where exactly a specific part should be located. More over I expected more from new molds (parts require a lot of work to remove additional plastic).
After some work done I need to say I am a little disappointed with this kit. Instruction includes some mistakes and it is not always easy to read how and where exactly a specific part should be located. More over I expected more from new molds (parts require a lot of work to remove additional plastic).
22 September, 13:17
Snake Plissken
Hi Marcin. My advice is to *expect mistakes* and do your research accordingly. It may or may not be fun to research the T-55 but most of the photos or line drawings you can find online are free, it just takes some time.
Hi Marcin. My advice is to *expect mistakes* and do your research accordingly. It may or may not be fun to research the T-55 but most of the photos or line drawings you can find online are free, it just takes some time.
25 September, 04:46
Snake Plissken
Good job adding the injector lines on the engine. I overlooked it the first time. 👍
Good job adding the injector lines on the engine. I overlooked it the first time. 👍
1 October, 05:53
Marcin Dudek
Thanks Snake 🙂. I was considering adding some more parts to the engine but they wouldn't be visible after assembly so I left it as it is. Thanks one again for the track bending tips, they were very helpfull.
Thanks Snake 🙂. I was considering adding some more parts to the engine but they wouldn't be visible after assembly so I left it as it is. Thanks one again for the track bending tips, they were very helpfull.
1 October, 15:48
Marcin Dudek
Some job with wearhering done. Still, I forgot to apply the decals first 🤦
Some job with wearhering done. Still, I forgot to apply the decals first 🤦
7 October, 05:41
Sergio Ordonez
přidal nové fotoalbum.
přidal nové fotoalbum.
29 19 August 2021, 11:46
Mark
The boys who, when my motorbike was stolen circa 1981, refused to investigate it as anything other than an insurance scam! Not the brightest folk I've ever met. I'll try not to hold that against your model Sergio, but can't promise. 🙂
The boys who, when my motorbike was stolen circa 1981, refused to investigate it as anything other than an insurance scam! Not the brightest folk I've ever met. I'll try not to hold that against your model Sergio, but can't promise. 🙂
3 September 2021, 14:24
Sergio Ordonez
🤣🤣🤣
Mark: I've been an AF Para back during my conscription. I really do not love those MP monkeys....
But I selected this one as there are some decals available and there are some parts that must be built from scratch. This will be a preparation for my next Landie: a British Amy EOD one.
Hope your motorbike was not a Royal Enfield or a Triumph or a Norton: this would be a great loss.
🤣🤣🤣
Mark: I've been an AF Para back during my conscription. I really do not love those MP monkeys....
But I selected this one as there are some decals available and there are some parts that must be built from scratch. This will be a preparation for my next Landie: a British Amy EOD one.
Hope your motorbike was not a Royal Enfield or a Triumph or a Norton: this would be a great loss.
3 September 2021, 17:15
Mark
Yamaha XT250. Absolutely loved that bike. It's been cars and bicycles since that was knicked. If I win the lottery tomorrow, I'll buy this: facebook.com/marketp..25539498668014/?ref=
You probably know that the RAF Police wear a blue beret, but I see the chap in image #6 is wearing a red beret like the Royal Military Police (Army).
Yamaha XT250. Absolutely loved that bike. It's been cars and bicycles since that was knicked. If I win the lottery tomorrow, I'll buy this: facebook.com/marketp..25539498668014/?ref=
You probably know that the RAF Police wear a blue beret, but I see the chap in image #6 is wearing a red beret like the Royal Military Police (Army).
3 September 2021, 21:42
Sergio Ordonez
Yes, I know: this one was a prototipe, it is my second time using Magic Sculpt and I'm still too green.
As you see, the figure is far from being perfect.
Yes, I know: this one was a prototipe, it is my second time using Magic Sculpt and I'm still too green.
As you see, the figure is far from being perfect.
5 September 2021, 12:23
Sergio Ordonez
Thank you very much, Mike, but is a little bot oversized and the mix of green stuff and Magic Sculpt proved to be not as addequate as needed.
I have been modifying figures of the old Italery "british tank troops" box to get cold war british soldiers (as these figures are a little bit smaller than others). I'm afraid 1:35 references for 70-80's british troopers are very limited, so this encouraged me to try modelling. The second try would be better.
Thank you very much, Mike, but is a little bot oversized and the mix of green stuff and Magic Sculpt proved to be not as addequate as needed.
I have been modifying figures of the old Italery "british tank troops" box to get cold war british soldiers (as these figures are a little bit smaller than others). I'm afraid 1:35 references for 70-80's british troopers are very limited, so this encouraged me to try modelling. The second try would be better.
6 September 2021, 14:05
Sergio Ordonez
I am terrible sorry, Mark: this stupid grammar corrector (is configured for Spanish, not for English). Sorry, I should check better before sending.
I am terrible sorry, Mark: this stupid grammar corrector (is configured for Spanish, not for English). Sorry, I should check better before sending.
7 September 2021, 14:49
Sergio Ordonez
Regarding the XT250, if you are looking for one, there are easy to obtain here in Spain under 3000€, and several are for sale. I think import taxes in Britain are around 12% plus VAT and, knowing that your MOT is a logical thing when compared to our ITV system would be relatively easy for you to get a license plate.
I know that Norton well, as there was one in the family. There were a lot of Norton bikes in Northern Spain in the 70s and 80s, but bought second hand from Canary Islands and Gibraltar. Very neglected, as spare parts were scarce. The Govt subsidies for new cars and bikes destroyed the rest and there are few to none survivors now.
Now I am working on getting a Land Rover Wolf from Britain (ex-MoD) for my farming operation. Hope to get one (or at least, pay less on taxes than on buying the Landie). 🤣
Regarding the XT250, if you are looking for one, there are easy to obtain here in Spain under 3000€, and several are for sale. I think import taxes in Britain are around 12% plus VAT and, knowing that your MOT is a logical thing when compared to our ITV system would be relatively easy for you to get a license plate.
I know that Norton well, as there was one in the family. There were a lot of Norton bikes in Northern Spain in the 70s and 80s, but bought second hand from Canary Islands and Gibraltar. Very neglected, as spare parts were scarce. The Govt subsidies for new cars and bikes destroyed the rest and there are few to none survivors now.
Now I am working on getting a Land Rover Wolf from Britain (ex-MoD) for my farming operation. Hope to get one (or at least, pay less on taxes than on buying the Landie). 🤣
7 September 2021, 15:14
Mark
No problem Sergio, I've lost count of the number of times I've got a name wrong online. 🙂
No problem Sergio, I've lost count of the number of times I've got a name wrong online. 🙂
7 September 2021, 19:24
Mark
Thanks for the tip on the XT250. I've used these sites for modelling research and they may help you find a good landie at a good price:
modsurplus.com/
army-uk.com/sub-equi..p?SID=16&SID2=16
modlandrover.com/
Thanks for the tip on the XT250. I've used these sites for modelling research and they may help you find a good landie at a good price:
modsurplus.com/
army-uk.com/sub-equi..p?SID=16&SID2=16
modlandrover.com/
7 September 2021, 19:30
Sergio Ordonez
Thank you very much, Mark! I did know the first one, but no clue about the others!
I have one question for you, as you served the RAF in these times... Those guys of the RAF Police, usually have helmets in their vehicles? I mean, back in the 80s (with all this means for good rock music).
Thank you very much, Mark! I did know the first one, but no clue about the others!
I have one question for you, as you served the RAF in these times... Those guys of the RAF Police, usually have helmets in their vehicles? I mean, back in the 80s (with all this means for good rock music).
8 September 2021, 00:45
Mark
Re helmets, I'd say probably not Sergio. The banner picture you use at the top of the project made me laugh at first - never seen RAF Plods running unless running to the mess! 🙂 And very odd to see them with SLRs.
If you didn't do helmets and kitted them with 9mm pistols or SMGs, nobody could argue that it wasn't authentic (* always depending on place/scene). DPM (disruptive pattern material) and ballistic vests as per your banner picture would be correct for Germany and Northern Ireland, but for most of UK mainland I'd expect to see them in RAF blue. UK Bloodhound sites and nuclear bomber sites, are probably best treated as for Germany. There are a lot of variables. Are you modelling any specific place/scene?
Re helmets, I'd say probably not Sergio. The banner picture you use at the top of the project made me laugh at first - never seen RAF Plods running unless running to the mess! 🙂 And very odd to see them with SLRs.
If you didn't do helmets and kitted them with 9mm pistols or SMGs, nobody could argue that it wasn't authentic (* always depending on place/scene). DPM (disruptive pattern material) and ballistic vests as per your banner picture would be correct for Germany and Northern Ireland, but for most of UK mainland I'd expect to see them in RAF blue. UK Bloodhound sites and nuclear bomber sites, are probably best treated as for Germany. There are a lot of variables. Are you modelling any specific place/scene?
8 September 2021, 11:10
Sergio Ordonez
I was thinking on RAF Brüggen or RAF Güntersloh. That photo I think was taken on Güntersloh, 1985, when some RAF Police troops try to capture a beer six pack.
Well, also I could change to RAF Blue uniforms (I think the wear caps instead berets, but also they usually patrol on Leyland Sherpa instead Landies).
Regarding the SLR, I found in photographs that whereas Royal Military Police usually appear using Sterling SMGs, RAF Police usually carry SLRs. And in most of photos, RAF monkeys wear INIBA vests. Maybe I should research a little bit more.
I was thinking on RAF Brüggen or RAF Güntersloh. That photo I think was taken on Güntersloh, 1985, when some RAF Police troops try to capture a beer six pack.
Well, also I could change to RAF Blue uniforms (I think the wear caps instead berets, but also they usually patrol on Leyland Sherpa instead Landies).
Regarding the SLR, I found in photographs that whereas Royal Military Police usually appear using Sterling SMGs, RAF Police usually carry SLRs. And in most of photos, RAF monkeys wear INIBA vests. Maybe I should research a little bit more.
8 September 2021, 17:15
Mark
"some RAF Police troops try to capture a beer six pack." 😄 😄 😄 Yes, I can see them running for that!
But that photo is a good reference for you - taken where/when you want to set your scene. If anybody argued about the authenticity of your model, you just show them that photo! Anyway our models are our creations and don't have to please anyone but ourself. 👍
"some RAF Police troops try to capture a beer six pack." 😄 😄 😄 Yes, I can see them running for that!
But that photo is a good reference for you - taken where/when you want to set your scene. If anybody argued about the authenticity of your model, you just show them that photo! Anyway our models are our creations and don't have to please anyone but ourself. 👍
8 September 2021, 18:23
Sergio Ordonez
Well, in fact, I'll be unable to build an authentic license plate, so you are completely right, Mark. Let's see what we get from here. The RE and the BDU ones will be better, but we need to start from here.
Thanks, Mark!
Well, in fact, I'll be unable to build an authentic license plate, so you are completely right, Mark. Let's see what we get from here. The RE and the BDU ones will be better, but we need to start from here.
Thanks, Mark!
8 September 2021, 18:44
Sergio Ordonez
Thank you, mate. Now seems closer to the end. This model is not fit for weathering, as some veterans told me RAFP Landies were neat and cleaned every week, so only small touches will be added, so, apart from some final assembly, this will remain more or less like this.
Thank you, mate. Now seems closer to the end. This model is not fit for weathering, as some veterans told me RAFP Landies were neat and cleaned every week, so only small touches will be added, so, apart from some final assembly, this will remain more or less like this.
21 September 2021, 06:19
Sergio Ordonez
Mark: I think these guys are ready to look for your motorcycle...
Mark: I think these guys are ready to look for your motorcycle...
21 September 2021, 14:32
Mark
It looks more like they're ready for tea break! 😄 Seriously though, I'm getting goose bumps from photo 33 onward - takes me right back in time. 👍
It looks more like they're ready for tea break! 😄 Seriously though, I'm getting goose bumps from photo 33 onward - takes me right back in time. 👍
21 September 2021, 18:49
Sergio Ordonez
Well, next one maybe will be an EOD RE one... Breaks are not for tea! 🤣 🤣 🤣
Thank you for your help, Mark. You and other veterans gave me ideas and the impulse to finish this one. After the WK Kafer I thought I had lost my mojo...
Well, next one maybe will be an EOD RE one... Breaks are not for tea! 🤣 🤣 🤣
Thank you for your help, Mark. You and other veterans gave me ideas and the impulse to finish this one. After the WK Kafer I thought I had lost my mojo...
21 September 2021, 19:05
Sergio Ordonez
Well, the REME EOD team build will be a kind of imagination: I'll mix again some different photographs for the final product. And I just realized that there is no Bowman Radio set available in 1:35 scale, but, let us try. 🤣
Well, the REME EOD team build will be a kind of imagination: I'll mix again some different photographs for the final product. And I just realized that there is no Bowman Radio set available in 1:35 scale, but, let us try. 🤣
22 September 2021, 16:56
Sergio Ordonez
Nice idea, David: RAF or RN? Royal Navy one is a kind of a heavy project if started from scratch.
Nice idea, David: RAF or RN? Royal Navy one is a kind of a heavy project if started from scratch.
9 October, 06:25
Sergio Ordonez
David, is that a coversion by Accrate Armour? I have the one by Revell for the supoorting of RN Choppers, but It is just an standard Landie.
David, is that a coversion by Accrate Armour? I have the one by Revell for the supoorting of RN Choppers, but It is just an standard Landie.
10 October, 18:21
David Taylor
AA do a full kit but it is expensive.Mine is a standard kit modified with styrene card and rods and anything else I could find.
AA do a full kit but it is expensive.Mine is a standard kit modified with styrene card and rods and anything else I could find.
10 October, 19:49
Sergio Ordonez
I would like to see your project, David. Looks really interesting and, as I still have a lot of spare Landies in my stash, I would like to replicate. But, first, I have to finish my Royal Navy collection: need to make low stock in my stash, as I cannot really find almost anything in my little workshop... 🙂
I would like to see your project, David. Looks really interesting and, as I still have a lot of spare Landies in my stash, I would like to replicate. But, first, I have to finish my Royal Navy collection: need to make low stock in my stash, as I cannot really find almost anything in my little workshop... 🙂
11 October, 05:11
Sergio Ordonez
You are right, David: infinite stash is a Common problem for all modelling mates.
Now I feel curious about the Chopper support Landies: I think I Will make some research.
You are right, David: infinite stash is a Common problem for all modelling mates.
Now I feel curious about the Chopper support Landies: I think I Will make some research.
12 October, 08:47
Sergio Ordonez
Yes, I used this kit, but I have a Firing Line hard top conversión kit I think It Will be useful for a RAF helo Support car. I have also found some captions of 1:76 scale drawings that Will be useful for the purpose.
Yes, I used this kit, but I have a Firing Line hard top conversión kit I think It Will be useful for a RAF helo Support car. I have also found some captions of 1:76 scale drawings that Will be useful for the purpose.
12 October, 17:43
Nicholas leenstra
vlastní tuto položku
vlastní tuto položku
A-10A Thunderbolt II Close Air Support Attack Aircraft
Great Wall Hobby (GWH) 1:48
L4825 2024 Nové díly 12 October, 17:30
Ken Judt
vlastní tuto položku
vlastní tuto položku
U.S. Air Force Jet Fighter
F-4C "Air National Guard" (First Limited Special Edition) Fine Molds 1:72
FP46S (FNMFP46S) 2021 Nové díly 12 October, 17:28
Thomas Voigt
označil tuto položku jako obchodovatelnou / prodejnou
označil tuto položku jako obchodovatelnou / prodejnou
12 October, 17:27
/cs/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=cs
35
35
/cs/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo