Novinky
Jeroen
označil tuto položku jako objednanou
označil tuto položku jako objednanou
German Destroyer Class 119 (Z1/Z5) [Platinum Edition] using metal parts
Revell 1:144
05179 2022 Model set 27 September, 13:25
Cristian L
will attend
will attend
33. Modellbau-Ausstellung PMC Main-Kinzig
Gelnhausen
28. a 29. Září 2024
28. a 29. Září 2024
27 September, 13:21
Frank
vlastní tuto položku
vlastní tuto položku
Auto Salon Series
Morgan Plus 8 Roadster with 1:72 scale Pitts Special LS 1:16
C2002: 3000 (2) 1982 Nové díly Multitéma (2)27 September, 13:19
Hrvoje
chce tohle
chce tohle
VF-201 Lone Star Hunters F-4N, F-14A
TwoBobs Aviation Graphics 1:48
48-285 2024 Nová forma Multitéma (2)27 September, 13:15
Soeren R.
vlastní tuto položku
vlastní tuto položku
Macchi MC.200 Saetta Late Series (Serie IV-XXIII) interior 3D decals for Italeri/Tamiya
Quinta Studio 1:48
QD48467 2024 Nová forma 27 September, 13:13
Soeren R.
vlastní tuto položku
vlastní tuto položku
Ka-52 Gun bay with 2A42 gun (3D-printed resin parts) for Zvezda kit
Quinta Studio 1:48
QT48025 2024 Nová forma 27 September, 13:13
Soeren R.
vlastní tuto položku
vlastní tuto položku
Ka-52 HUD exterior 3D decals (with 3D printed parts) for Zvezda
Quinta Studio 1:48
QP+48039 2024 Nová forma 27 September, 13:13
Sy Bar
přidal nové fotoalbum.
přidal nové fotoalbum.
14 obrázky
Bf110C-6Nový: 27 September, 13:13 1:72
Hopefully one of these will sort the decals out
Projekt: Bf-110C-6
18 18 September, 11:53
Sy Bar
Was going to do the Battle of Britain version of this kit but I'm temped to have a go at some winter white wash and the wasp is cooler than the shark mouth 😎
Was going to do the Battle of Britain version of this kit but I'm temped to have a go at some winter white wash and the wasp is cooler than the shark mouth 😎
18 September, 11:56
István Szücs
I also have Bf-110 from the Airfix, I will build an Italian night fighter. The sprues are the same, so I'm watching!
I also have Bf-110 from the Airfix, I will build an Italian night fighter. The sprues are the same, so I'm watching!
18 September, 19:08
Sy Bar
Cheers guys.
I'm have a go at riveting, but going freehand as at this scale using tape was taking so long. I also not sure how much they will stand out on finish kit, but with the wonky line in parts they will probably bee seen from mars 🤣
Cheers guys.
I'm have a go at riveting, but going freehand as at this scale using tape was taking so long. I also not sure how much they will stand out on finish kit, but with the wonky line in parts they will probably bee seen from mars 🤣
22 September, 10:15
Sy Bar
Cheers #Guy 👍
#Skyhiker I found the fit to be good, I had a very slight gap at the front but think that was as much to do with me and the fitting of the pit (not the clearest instructions there). Every thing else was fine and the canopy was a good fit, I did change order of build slightly with the tail section I glued the rear piece to the body first then added the tail (after I'd added the stabilisers/rudders) this made more sense than the instructions 😁
Cheers #Guy 👍
#Skyhiker I found the fit to be good, I had a very slight gap at the front but think that was as much to do with me and the fitting of the pit (not the clearest instructions there). Every thing else was fine and the canopy was a good fit, I did change order of build slightly with the tail section I glued the rear piece to the body first then added the tail (after I'd added the stabilisers/rudders) this made more sense than the instructions 😁
24 September, 21:32
Sy Bar
Only issue I have with this kit are the decals. While they look great and are in perfect register, they have a large amount of film edging and are both thick and delicate at the same time🤪
Having a hard time getting them to settle into the panel lines etc. I usually just need to use micro sol but even ultimate extra strong is not have much effect. Going to have to wait till I get some Tamiya fixer, strong and extra strong hopefully one of these will help 🤞
Only issue I have with this kit are the decals. While they look great and are in perfect register, they have a large amount of film edging and are both thick and delicate at the same time🤪
Having a hard time getting them to settle into the panel lines etc. I usually just need to use micro sol but even ultimate extra strong is not have much effect. Going to have to wait till I get some Tamiya fixer, strong and extra strong hopefully one of these will help 🤞
24 September, 21:44
Soeren R.
vlastní tuto položku
vlastní tuto položku
MiG-17F / Lim-5, U.S.S.R., GDR Premium Special Edition
Ammo by Mig Jimenez 1:48
A.MIG-8512 2023 Nové díly 27 September, 13:12
/cs/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=cs
35
35
/cs/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo