Novinky
Loginthesand
chce tohle
chce tohle
RE/100
AMX-107 BAWOO Neo-Zeon Attack Use Prototype Transformable Mobile Suit Bandai 1:100
0210512-3500 (006) 2016 Nová forma 18 September, 05:49
Steiner_76
Frage ist sind das nur Dateien für Leute, die ein 3D Drucker haben?
Frage ist sind das nur Dateien für Leute, die ein 3D Drucker haben?
Panzer IV
Road Wheel set - open hub cap for Gunze / Revell / DML (old tooling) Tankbrusher Scale Modeling 1:35
352409007 2024 Nová forma Digitální: 3D datový soubor18 September, 05:45
Goldman
přidal nové fotoalbum.
přidal nové fotoalbum.
12 obrázky
Freightliner FLD WIP1:24
I built the base chassis 25 years ago. Checking it I don't see any major alignment issues. Had to clean many moulding li...
Projekt: Freightliner FLD 120
4 1 August, 04:59
Greg Baker
přidal nové fotoalbum.
přidal nové fotoalbum.
24 19 June, 14:33
Greg Baker
First print mostly successful. I will need to rework the thickness of the walls and the support struts for the roof. Much too thin.
First print mostly successful. I will need to rework the thickness of the walls and the support struts for the roof. Much too thin.
19 June, 14:35
LucLuke B
3d printing, I wouldn't know where to start. Is the ami 6 a file you found online?
3d printing, I wouldn't know where to start. Is the ami 6 a file you found online?
19 June, 19:39
Greg Baker
I did find it online, but was a little disappointed with the quality. It required a lot (and will need more) work to be able to print it. I mainly have to increase the thickness of the rear trunk area. The strange overhang roof in the rear needs to be sturdier as well.
I did find it online, but was a little disappointed with the quality. It required a lot (and will need more) work to be able to print it. I mainly have to increase the thickness of the rear trunk area. The strange overhang roof in the rear needs to be sturdier as well.
19 June, 19:59
Greg Baker
The second printing went much better. I made a mistake though, I forgot to add the support to both sides of the rear roof struts. Luckily one side seems to be strong enough to hold everything, and with a little paint I don't think the thin part will be visible.
The second printing went much better. I made a mistake though, I forgot to add the support to both sides of the rear roof struts. Luckily one side seems to be strong enough to hold everything, and with a little paint I don't think the thin part will be visible.
20 June, 14:08
Greg Baker
Good timing. After a bit of a summer break spent watching football, olympics, and playing video games with my son... I just started back at the modelling desk. After clearing up a couple of other, smaller, Tintin-related projects, I'm almost ready to tackle this one again.
Good timing. After a bit of a summer break spent watching football, olympics, and playing video games with my son... I just started back at the modelling desk. After clearing up a couple of other, smaller, Tintin-related projects, I'm almost ready to tackle this one again.
21 August, 14:09
Greg Baker
With the Hawker Hart off the bench and on the shelf… I guess it's time to tackle this one again. Getting the colour right was tricky. I finally settled on a 10:5:1 ratio of Tamiya XF-2 White, X-14 Sky Blue and XF-18 Medium Blue. Not perfect, but close enough I think.
With the Hawker Hart off the bench and on the shelf… I guess it's time to tackle this one again. Getting the colour right was tricky. I finally settled on a 10:5:1 ratio of Tamiya XF-2 White, X-14 Sky Blue and XF-18 Medium Blue. Not perfect, but close enough I think.
18 September, 05:30
/cs/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=cs
35
35
/cs/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo