Bf 110E-3/Trop

1
January 18, 2019
2
January 27, 2019
Determining, where to cut and what to rescribe
3
January 27, 2019
Position of the camera realtive to cockpit floor
4
January 28, 2019
Filling in the chutes and vents, prepared for rescribing
5
January 29, 2019
Camera window cut out
6
January 29, 2019
cockpit floor peeking though - trimming required!
7
January 29, 2019
Dragon's seat-adjustment(?) grip vs. scratch-build
8
January 29, 2019
Completed handle and hollowed out housing
9
January 29, 2019
Rudder pedals thinned down
10
January 30, 2019
11
January 30, 2019
12
January 30, 2019
13
January 30, 2019
14
February 2, 2019
New book and parts: Aufklärer Vol.1 and RB50/30 camera from AIMS
15
February 2, 2019
Unused Dragon parts - might come in handy for the mounting frame
16
February 3, 2019
CAD sketch for the camera mounting frame
17
February 4, 2019
Camera model added for dimensional adaption
18
February 4, 2019
MG 15 with Master barrel
19
February 6, 2019
AIMS rear seat with scratch build support, handles on the front ammo drums added
20
February 6, 2019
Dust covers for the MG17s from brass tube
21
February 10, 2019
Instrument panel - only missing the Revi plug
22
February 10, 2019
Left cockpit side: Lots of detail missing, wing root will be visible
23
February 10, 2019
Right console: some small stuff missing, opening for cables in the wrong place
24
February 10, 2019
Almost complete cockpit
25
February 10, 2019
Instrument housings and cables added
26
February 10, 2019
Shot counter for the MG FF faired over
27
February 12, 2019
Valves added from stretched sprue and copper wire
28
February 12, 2019
HGW rudder pedals with Tamiya tape straps
29
February 12, 2019
Linkages added to opening in thorttle quadrant
30
February 12, 2019
Camera motor, with felxible shaft and pressure hose
31
February 14, 2019
Camera auxillary units: Bildfolgeregler and Ueberdeckungsregler - first try
32
February 14, 2019
Camera frame 3D printed via fused filament - fail!
33
February 15, 2019
Resin exhausts and some other stuff
34
February 15, 2019
Dry fit on the starboard cowling - quite some work to do
35
February 15, 2019
Wheel well finished
36
February 15, 2019
Landing gear, missing brake line
37
February 17, 2019
Comparison of drop tanks from stash
38
February 17, 2019
Engine instruments from Mdc
39
February 17, 2019
Dry fit of Quickboost exhausts
40
February 17, 2019
Prop dry fit, lots of sanding needed on the cowling
41
February 25, 2019
42
February 27, 2019
43
February 27, 2019
44
March 5, 2019
Motivational dry fit - both wings and ancelles are finally finished. Now everythings waiting for the camera mounting frame
45
March 5, 2019
IP with Revi plug and the IP lights added, comparison Dragon Revi vs. Quickboost
46
March 5, 2019
The assembled IP
47
April 5, 2019
Finally - the 3D printed camera frame!
48
April 6, 2019
Disaster strikes - even with careful sawing with the finest PE saw I had, the frame shattered
49
April 6, 2019
Lots of patience later it's almost reconstructed. One part of the arch is missing - have to crawl over the floor again
50
April 7, 2019
Repair with styrene - still needs some trimming
51
April 7, 2019
52
April 7, 2019
Mock up with the cockpit floor
53
April 9, 2019
The primer unforgivingly reveals all the flaws
54
April 10, 2019
Small collision problem
55
April 10, 2019
The height of the camera assembly seems accurate compared to oroginal pictures
56
April 14, 2019
Some paint on the frame and camera. Not ssure about the latter. I read about a blue-grey camer colour but there are only pictures from cameras in beige and dark grey
57
April 16, 2019
RLM02 over black base - tried to keep it irregular
58
April 16, 2019
Quick dry fit with the cockpit floor to get an impression
59
April 25, 2019
RLM66 for the IP, Bordfunkers gauges and the morse code box
60
April 25, 2019
Radio equipment and camera painted blue grey. Beige and brown for the rear seat
61
April 25, 2019
Started painting on the MG15. Still needs some graphite for the metal effect, but the bakelite rear end and the fabric cover are mostly done
62
April 28, 2019
Most of the detail painting done
63
April 28, 2019
The IP was pretty hard to paint - still not 100% satisfied
64
April 28, 2019
Dry fit
65
April 28, 2019
66
April 28, 2019
67
May 4, 2019
Placards (from MDC) added. The ones on the radio are 1/48
68
May 19, 2019
69
May 19, 2019
70
May 23, 2019
HGW seatbelts in place and dry fit of the cockpit
71
May 23, 2019
eduard seatbelts for the pilot's seat
72
June 11, 2019
seatbelts in place with the details higlighted by a brown wash
73
June 11, 2019
final touch: some pigments for dust and dirt on the cockpit floor
74
June 13, 2019
75
June 13, 2019
76
June 13, 2019
77
June 13, 2019
78
June 16, 2019
Minor fit issues on the belly section
79
June 16, 2019
80
July 7, 2019
The wings are finally on and dry fitting on the canopy is in progress
81
July 14, 2019
lots of masking on the canopy
82
September 22, 2019
canopy in place, RLM02 pn the insied; black base on the outside
83
September 22, 2019
Hasegawa drop tanks, with Dargon's brace and fuel pipes from copper wire
84
October 19, 2019
black base is on!
85
October 20, 2019
marble coat for the insignia
86
October 20, 2019
blending with off white
87
November 10, 2019
masked up
88
November 10, 2019
covered with Tamiya Nato black and black
89
November 10, 2019
first mask pulled - yes!
90
November 26, 2019
all masks in place and sealed
91
November 26, 2019
RLM78 marble in place
92
November 26, 2019
93
November 26, 2019
94
November 26, 2019
lower cowlings left blank - they were probably yellow
95
November 30, 2019
white marble base
96
November 30, 2019
yellow applied - still not happy with the result. Might try MRP yellow next time
97
November 30, 2019
Underside painted MRP RLM78
98
November 30, 2019
the crosses turned out a little bit too dark - they'll recieve another coat of white
99
November 30, 2019
contrast is a little too heavy fo rmy taste
100
December 8, 2019
contrast corrected, underwing codes applied
101
December 8, 2019
102
December 8, 2019
some weird lifting - never had an issue with MRP or Tamiya before..
103
December 8, 2019
RLM79 marble started
104
December 8, 2019
new marble technique
105
December 8, 2019
using a template over the base marble to get a more irregular pattern
106
December 20, 2019
RLM79 marble finished, added contrast with tan and brown
107
December 20, 2019
the effect is pretty subtle to invisible
108
December 22, 2019
RLM79 is on!
109
December 22, 2019
quite translucent - final look will be achieved after the RLM80 stripes
110
December 22, 2019
111
December 22, 2019
RLM70 for the prop, variation with Radu's mask in lighter and darker green; chipping via hairspray
112
December 24, 2019
finished props and spinner
113
December 24, 2019
black base for the RLM80 stripes
114
December 26, 2019
stripes in place!
115
December 26, 2019
116
December 26, 2019
117
December 26, 2019
some weird liftung on the insignia - have to fix that
118
December 26, 2019
119
December 30, 2019
Drop tank with decals from Revell's Bf 109G-6 - the flat carrier film is a pain in the **s
120
December 30, 2019
Quickboost exhausts painted with Alclads: steel base, followed by pale burnt metal and jet exhaust near the openings
121
December 30, 2019
pin wash applied to the RLM02 parts
122
January 4, 2020
salt faing - looking good from afar
123
January 4, 2020
paint ate through to the black base
124
January 4, 2020
125
January 4, 2020
repaired; needs some polishing
126
January 4, 2020
lots of dots
127
January 4, 2020
blended in; more dark oils applied to the exhaust stain area
128
January 4, 2020
oil dot filter in place
129
January 4, 2020
oils applied to the exhausts
130
January 26, 2020
started the exhaust stains with oils
131
January 26, 2020
filter on the upper sides
132
February 15, 2020
panel line wash in place
133
February 15, 2020
kept it subtle
134
February 24, 2020
underside wash in place
135
February 24, 2020
quick mock up
136
February 24, 2020
137
February 24, 2020
138
March 1, 2020
pigments applied to the wheels - meh
139
March 1, 2020
oversprayed with Tamiya buff; way better
140
March 1, 2020
started to redo the lost antenna mast, Vallejo sand as base coat
141
March 1, 2020
burnt umber streaked on
142
March 1, 2020
added chips with silver oil colour and exhaust stains with MRP
143
March 1, 2020
more chips
144
March 1, 2020
fuel and oil stains
145
March 1, 2020
more staining on the drop tanks
146
March 1, 2020
almost done!
147
March 1, 2020
148
March 9, 2020
antenna mast and aerial wire finally in place

Komentáře

4 18 January 2019, 15:08

Rui S
Nice work 👍

29 January 2019, 23:34

Nathan Dempsey
Great start. I'm watching this one.

30 January 2019, 17:11

Joachim F.
Thanks mates - there's a build log over on largescaleplanes😉

30 January 2019, 17:45

Spanjaard
interesting

2 February 2019, 14:22

Stephan Ryll
Very detailed work 👍

15 April 2019, 18:15

Rui S
Nice Paint job. 👍
Looking forward to see the Next pieces.
The engine instruments and the scratch also look great.

25 April 2019, 23:53

Warren Inman
Stupid me built the cockpit for this model and have misplaced it! Is on hold until I find the damn thing! 🙂

26 April 2019, 00:40

Rui S
Shit happens😉

26 April 2019, 07:55

Joachim F.
Good luck finding this tiny thing!

28 April 2019, 15:05

Warren Inman
This is a 1/32 Bf 110.. not very tiny at all..

28 April 2019, 23:42

Joachim F.
I obviously forgot my irony sign😉

29 April 2019, 05:29

komoras
Never saw such an awesome Bf 110 being built! Great work! 👍

30 November 2019, 15:33

Spanjaard
impressive paint job so far

30 November 2019, 23:12

Joachim F.
Thanks mates - I'm blushing behind my screen!
Although I'm going to put some more work into the RLM78.

2 December 2019, 10:35

Oliver Peissl
Sieht Super aus bis jetzt, Sehr schön!!

4 January 2020, 18:16

Joachim F.
Vielen Dank Oliver!

5 January 2020, 07:32

Murad ÖZER
i've read about paint eating it's way tru earlier at lsp, hard to understand how something like this did happen, even harder to understand how you felt as you first saw wtf is going on...man! still a great save. 👍

5 January 2020, 08:05