1970 Corvette Coupe LT-1/ZR-1 C3 - wip
Komentáře
1 7 June 2019, 09:54
Bob Hall
I'm going to go out on a limb and guess, Maybe Just Maybe, you might like Corvettes, I just can't quite put my finger on it ????????? LOL ! Looking Great !
I'm going to go out on a limb and guess, Maybe Just Maybe, you might like Corvettes, I just can't quite put my finger on it ????????? LOL ! Looking Great !
9 June 2019, 20:33
Christian W
🙂 The Corvette is cool. Like it. I like Pontiac Firebird, Honda and the old Beetle too. But I put that project with the silver Corvette into my mind and try to get through it until I'm bored *lol*
Some kits (especially the older kits) are a challenge. This is one reason to do it. I like the old kits and the challenge to put a good looking kit on the wheels.
I'll do my best😉
🙂 The Corvette is cool. Like it. I like Pontiac Firebird, Honda and the old Beetle too. But I put that project with the silver Corvette into my mind and try to get through it until I'm bored *lol*
Some kits (especially the older kits) are a challenge. This is one reason to do it. I like the old kits and the challenge to put a good looking kit on the wheels.
I'll do my best😉
9 June 2019, 20:38
Christian W
Today I'm sorting out, which model kits will make it into the SILVER collection. Maybe the other kit get it into the shelf anyhow.
Today I'm sorting out, which model kits will make it into the SILVER collection. Maybe the other kit get it into the shelf anyhow.
9 June 2019, 20:39
Slavo Hazucha
Thumbs up for the Coke bottle Corvette! 👍 That shape looks great even without wheels & the rest on it... Give it time, make it shine!😉
Thumbs up for the Coke bottle Corvette! 👍 That shape looks great even without wheels & the rest on it... Give it time, make it shine!😉
9 July 2019, 05:54
Christian W
Thank you! I think the angle of the latest picture shows the sexy design at it's best 🙂 I love the shape of the front fenders. The body will be sitting for a minimum of 10 days until it's getting wet sanded and afterwards the second layer of clearcoat. It will get it's time.
Thank you! I think the angle of the latest picture shows the sexy design at it's best 🙂 I love the shape of the front fenders. The body will be sitting for a minimum of 10 days until it's getting wet sanded and afterwards the second layer of clearcoat. It will get it's time.
9 July 2019, 05:58
Gordon Sørensen
The paint you laid down on the main body looks fantastic! Nary a ripple or run to be seen...
The paint you laid down on the main body looks fantastic! Nary a ripple or run to be seen...
9 July 2019, 13:33
Christian W
Thank you. It will get a wet sanding and a second layer of clear coat. There are some small dots on the rear and. Next week I will lay my hand on it.
Thank you. It will get a wet sanding and a second layer of clear coat. There are some small dots on the rear and. Next week I will lay my hand on it.
19 July 2019, 21:29
Christian W
Thank you! Yetserday I was proud about the results. Hopefully today they still look amazing 😄 Now I can paint the details on the kit and put it together.
Thank you! Yetserday I was proud about the results. Hopefully today they still look amazing 😄 Now I can paint the details on the kit and put it together.
23 July 2019, 05:00
Christian W
Thank you. On my point of view it looks amazing in silver. The curves are so lovely😉
Thank you. On my point of view it looks amazing in silver. The curves are so lovely😉
11 August 2019, 08:55
Christian W
Thank you! I like it too.
I don't know why AMT didn't check the sitting of the wheels. If they wouldn't had done this small inner ring around the pin (which I sanded down), the wheels would fit perfect into the wheelhouse.
Thank you! I like it too.
I don't know why AMT didn't check the sitting of the wheels. If they wouldn't had done this small inner ring around the pin (which I sanded down), the wheels would fit perfect into the wheelhouse.
15 August 2019, 04:26