Zeď
Wall
April 16, 2024
March 22, 2024
March 17, 2024
![](/profiles/img/58017-515-s.jpg)
přidal nové fotoalbum.
All comments (18) » 28 15 October 2023, 16:07
![](/profiles/img/58017-515-s.jpg)
I am now in a very dark place... put some "decap four" the spray used for hoven cleaning. fingers crossed...
17 March, 20:04
March 9, 2024
January 25, 2024
January 19, 2024
![](/profiles/img/58017-515-s.jpg)
přidal nové fotoalbum.
All comments (6) » 14 9 August 2023, 15:11
![](/profiles/img/12266-435-s.jpg)
I personally am strongly opposed to "improve" or redo a certain model you have built a long time ago. It is a time capsule, it depicts your skill level at a certain point in time and there are memories attached to it, please leave the old builds like they are! I actually myself did that several times what you suggest, I built the same kit many years apart just to see how much I improved. 👍
11 August 2023, 16:08
![](/profiles/img/58017-515-s.jpg)
Indeed yiu are right but some of them lost too many pieces or broken down afger an unscheduled flight over to the shelves. In this case choice is either the trash or reshuffle. As i am a bit holding on them i rebuild them or replace them with a new kit
19 January, 08:09
January 14, 2024
![](/profiles/img/58017-515-s.jpg)
přidal nové fotoalbum.
All comments (5) » 5 14 January, 08:52
![](/profiles/img/33587-335-s.png)
Following this one 👍 Had been contemplating doing one of these boats... will you improve the kit using scratch details or such?
14 January, 20:01
![](/profiles/img/58017-515-s.jpg)
@tom Thank you ! I started to complete the bridge, It is very small not sure I am able to improve without etch part, may be main antena that look very thick but I will concentraten to fill the gaps every each pieces.
14 January, 20:58
January 13, 2024
August 26, 2024
December 31, 2023
December 12, 2023
November 1, 2023
October 31, 2023
October 26, 2023
![](/profiles/img/58017-515-s.jpg)
přidal nové fotoalbum.
All comments (12) » 32 9 August 2023, 07:38
![](/profiles/img/58017-515-s.jpg)
here the pictures of the final model. a lot of work far from perfect in particular in metallic shine but look like a Mig-19. Despite multitude of boxes, only 2 mold on the market all pre date 80s. I will definitively try another build. this time with brand new kit.
26 October 2023, 14:11
October 15, 2023
September 4, 2023
![](/profiles/img/58017-515-s.jpg)
přidal nové fotoalbum.
All comments (16) » 26 11 December 2019, 17:05
![](/profiles/img/58017-515-s.jpg)
@ Andy Ball : definitively !! @ Simon & PeterThank you very much.
4 September 2023, 04:18
![](/profiles/img/58017-515-s.jpg)
I split the collection into WWII plane (here) and Post WWII : Soviet plane Cold War 1/72 | Album by Naram
4 September 2023, 04:19
September 3, 2023
![](/profiles/img/58017-515-s.jpg)
přidal nové fotoalbum.
All comments (20) » 28 31 December 2022, 15:07
![](/profiles/img/73194-710-s.jpg)
I've never got rid of such an amount of raised detail, but given there are no complex curves on the surface of the SR-71 my approach would be to sand it away using flat files or, better, some DIY flat sticks. Just grab a piece of styrene bar and glue a strip of sand paper to it with CA. Evergreen 0,6x0,15 bar works well for me because it's broad and flexes a little so you can adjust the strenght of the sanding. I use 800 grit wet paper for a start, de-clogging it periodically with a hard bristle brush in a glass of water. Please see pic 31 in my CL 415 album:
CL-415 MP MMEA | Album by drmeizoso (1:144)
I think this way you could remove the lines pretty fast leaving no dents, as it usually happens when using scalpel blades or scribers. Then you just have to swipe a sanding sponge to smooth everything up.
If you want to keep track of the original panel lines you can first take pictures of the original lines as a precaution, then sand, and puncture the intersections of the lines with a needle when you are almost done but the remnants are still visible. This way you just have to scribe following the dots afterwards, checking the pics for reference if in doubt.
As for the scribing part, I can recommend Border's cemented carbide engraver 0'15mm for 1/72 and any scribing tape (HIQ parts, Dymo, cello tape...) as a guide.
Keep the good work! Of course I'll follow this, it's a personal favourite!
3 September 2023, 15:18
August 28, 2023
August 27, 2023
wnolder.php?lang=cs
2023-08-27 12:06:54
2019-09-30 13:05:21
58017
/ajax/wnolder.php?lang=cs&sd=2023-08-27 12:06:54&md=2019-09-30 13:05:21&filter=&w=58017
todo