Newsfeed

Nicolas
I used the good wether today to work on the smaler parts for the Fallout diorama again. The most figures don't fit OOB, so are modified or combinations from different figures from the (up to now 4) figure sets.

gorby
Nice diorama.

Oleksii
Thank you)))

CaptGPF
Lovely dio

Oleksii
Thank you 🙂

Palo M
Looks great! One nit: it was still Czechoslovakia in 1990 🙂

Oleksii
Thank you very much, i have corrected

Michael Kohl
Nice. Leaving the surface texture of the foam board for the apron makes it look quite east european indeed. Nice twist. Adding a frame would give this nice dio a bit more of a professional appearance. Just a thought.

Oleksii
Thank you, on my next diorama i would try to find a frame or make it.Do you have any advice for frames?

Michael Kohl
You can make a simple cover for your dio with veneer or plasticcard just cut to size and glued blunt. Quite a few use readymade picture frames. This is convenient. In my opinion two aspects can make it look a bit off: first if the dio is made to fit the frame and not vice versa. And second if the level of the frame is higher than the level of the dio. This can easily be avoided by putting in a higher foam board. Wooden profiles can be cut at 45° angle and fit around the foam. This allows you to fashion any size you want. I have covered irregular shapes with veneer and with simple card board that I varnished afterwards.
Have a look around here. There are plenty of excellent solutions to be found - and a few which show possible pitfalls.
Half a dozen techniques you will find at my stuff (including not so good ones 😉 ).

Guy Rump
Very nice build! 👍

Oleksii
Thanks you very much Michael for this advices.I would give my best and show next on my diorama.( Probaly in 2-3 weaks)

Oleksii
Thank you Guy Rump🙂

Ekki
Beautiful!

Oleksii
Thanks, guys, for your words and likes. I really appreciate it

J35J
Great work with kits and dio!👍🏻

Rui S
Welcome to scalemates🙂

EliWithThatOlds
Thank you!

Cristian A
Watching! I have the same kit as my next project 👍😃

Ferenc Sarka
I made the revell version earlier. A little bit better but neither of them is issue free. The revell unreachable on the market, just the italeri version. Good luck for your project.

Ekki
Following.

Thomas Kolb
I am definitely following this build. The Italeri kit is not an easy build (and it is a model of the very first A-version of the Gripen, not the C-version used by Hungary), but it is the only one that exists today. I am however sure you will do a splendid job!

Roland Sachsenhofer
With these pictures I open the book report on Roden's Junkers D.1: I tried to extend the interior with some steel wire, the seat belts are from Eduard. For the detailing I downloaded the very interesting building instructions from Wingnut Wings for the large D.1 in 1:32, which is quite helpful if you want to have a good documentation as a basis for detailing. I'm also going to realise one of the WW variants, which I immediately liked: all in Dural/ NMF with only a minimal set of markings.

gorby
Nice work so far. Looking forward to this. 🙂

Michael Kohl
Auch da bin ich dabei.

Roland Sachsenhofer
I'm very pleased - appreciated!

bughunter
Watching!
I have done the short fuselage already, I hope one day I can do the long one too.

Is the engine painting finished? I can recommend the WNW manual for this, still available on WNW page.

Roland Sachsenhofer
Thanks for the tip - it's definitely a good one! The printed WNW instructions are next to me, so I want to use a little oily black on the top of the engine and add a little "brass"... But not only WNW instructions, also your excellent work is my reference.

Villiers de Vos
Very nice progress.

Roland Sachsenhofer
Thank you for your words, appreciated!

Roland Sachsenhofer
The fuselage of the D.1 is now closed, the only thing to be careful of was not to damage the corrugated sheet metal joints. A related issue arises with the leading edges of the wings: in my opinion, the prototype shows a continuous line around the leading edge.... this will be difficult to depict: I will try to get close to this with careful sanding and the same amount of reworking with a scalpel.

Roland Sachsenhofer
Now it worked with the upload of the pictures!

István Szücs
My favourite plane from the Great War-era, I'm watching!

bughunter
Yes to clean the wing seem is not that esay. I must admit I used also wings from another kit after I was not happy with the first try. I have both the long and short fuselage kits and the wings are the identical. But that shifts the problem only to a later date, when I will build the long one. A new Part PE set is waiting too 🙂

Roland Sachsenhofer
Thank you for your words, mates! - I completely agree that this is not an easy topic! My approach, which you can see started here, is to work on the front edge of the profile with a triangular file. I didn't even try to bring the corrugated sheet metal runs of the top and bottom together - that would be far too small for me - but simply used the file edge many times.... Well, in my opinion it looks at least a little better now than before, so I'll try to make it a little more precise....

Roland Sachsenhofer
The Alclad metal colours mercilessly bring out all the flaws and imperfections, especially when everything has already been trimmed to a high gloss in preparation for applying the decals like here! The Wingnut Wings instructions describe an effect called 'tiger stripes' on the wing sheeting, which I recreated using various aluminium and dural colours.

Robert Podkoński
A little late, but joining the party!

bughunter
The stripes are great - can be noticed, but both shades still looks like aluminium which it was.

Christian Abraham
Great build so far

Roland Sachsenhofer
Thank you very much, mates!
The opinion on the 'tiger stripes' really really pleases me in a very motivating way!

Guy Rump
Following. 👍

David Taylor
Watching.

Roland Sachsenhofer
That is appreciated as well! 🙂

Villiers de Vos
Very nice detailed work.

Roland Sachsenhofer
Thank you for your comment!

Ludvík Kružík
Roland, your model looks very good. I really like the interior of the plane and the engine. Also your rendition of the corrugated sheet metal looks very realistic. 👍

Roland Sachsenhofer
Ludvik, thank you for this comment, giving me a push to get the finishing steps done!

Dietmar Bogatzki
Wieder ein Meisterwerk von Roland 👍 hau rein 😉

Roland Sachsenhofer
Ich sage herzlich dank für den ermutigenden Kommentar! 🙂

Roland Sachsenhofer
A few steps closer to a finish: working with Roden decals is always an adventure, happy end not guaranteed! The whole thing is spiced up by the corrugated metal nature.... Well, this is the result; I will of touch up up the unclean parts with a brush, but on the whole it will stay like this - now for the signs of use and wear!

bughunter
Brave, brave - with good results 👍
I hadn't even tried those.

Roland Sachsenhofer
Thank you! 🙂
The Junkers D.1 is slowly approaching its final appearance - and that didn't work out quite as well as I had imagined! But what the heck, there are some nice things, like the turnbuckles or the two MGs from Gespatch; I'm also happy with the solution for the typical Junkers handles and footrests: a thin, glued-on metal rod was covered with finely cut Tamiya tape as a ridge. Well. I am satisfied with this overall impression.

Ludvík Kružík
As the work progresses, Junkers grows in beauty. Thanks to decals and small details the model looks better. 👍

Roland Sachsenhofer
Thank you for your kind comment, Ludvik!

Robert Podkoński
Watching with interest!

Vincent
Impressive work already at this scale!!

Robert Blaschke
Thanks. It fits together well. 🙂

Guy Rump
Following. 👍

bughunter
After a health problem, I stopped modelling for a short time. I didn't want to continue the projects I had started because I wasn't in the mood for scratch modelling. I wanted to make a quick project - almost oob. Of course with a wooden propeller, because building one is just fun.
Working on two Pfalz D.IIIa (one as a triplane conversion) a long time ago was great fun and there was still a special kit waiting in my stash: a Limited Edition Dual Combo Pfalz D.III. No, I haven't forgotten the "a", this really is the forerunner of the D.IIIa. Eduard has re-released the D.IIIa kit often, but this Edition is from 2005 and was never released again. I hear some voices: Limited Editions are for collecting, not building. Never mind, I'm building the kit now!

I'm building the machine from the cover picture - and because there's a heart on it, I'm dedicating the build to my wife, who always supports me!

John
Looks great!

Nathan Dempsey
Following. Welcome back!

Kyle DeHart
Excellent to see you Frank!! I can't wait to follow along with this. Which is sure to be another beautiful build. Any edition…Limited, or otherwise sounds like something to build to me!! But maybe I'm doing things wrong. Ha!!

Erik
Zum Glück bist Du wieder fit! 👍
Sieht mal wieder klasse aus, die kleinen Steuerseile sind geil. 🙂

gorby
Looks like an interesting project Frank. I must admit that I don't know much about WWI aircraft and your builds are often a lesson about the real machines as well as a lesson in modelling.

Robert Podkoński
Taking a seat, of course!

bughunter
Thank you very much mates! Great to know that you are following 👍
Yeah Kyle, all kits can be build. But some collects rare kits as investment and hope to sell it later for higher prices. Once started the value goes near zero. But we have fun building them and that is invaluable!
@gorby You will see later that the Pfalz fighters are elegant planes!

Kyle DeHart
Indeed. I take a great pleasure in opening up and building valuable kits. I would be a really horrible collector. Lol.

Martin Oostrom
I have a few rare ones. But I'll gladly build them when the time comes. That's what kits are for!

KyMustang
Charming little airplane and great job on the build so far.

David Taylor
Watching.

Marcel Klemmer
I am in

Zbynek Honzik
Taking a seat!

Ben M
watching!

bughunter
A warm welcome to the show also for the new visitors!
I hope to have it ready for our next club meeting, so it will be a quick build (for my standards).

Michael Kohl
Good to see you back at the bench. I consider the Pfalz DIII one of the most elegant WWI planes and have two in my stash too. So I won't miss this build.
Keep it coming.

Kyle DeHart
The Pfalz really does have a lovely shape.

Ludvík Kružík
I'm also glad you're back on the bench. I really enjoy watching you build models.

... by the way... I really like to buy Eduard limited edition models. They include lots of extras and often a publication with photos and information about the type whose model is in the box. I still have some of the limited edition models in my closet. Not because I just collect them, but because I haven't managed to build them yet. 🙂

Bruce Huxtable
I'm sorry to hear that you had a health scare, and hope that all is okay again for you. Your projects are always inspiring and a joy to follow. Have fun bringing this special one to life 🙂

bughunter
Thank you very much mates! Your nice comments are highly appreciated!
I hope to show later new pictures showing the elegant lines even more.
@Ludvik Since this is an older kit in this case not a single word about the type! Only a ink jet printed manual, and one colorful, nicely printed sheet showing the six markings including decal placement. Anyway, the kit parts and PE are nice, a mask is also included.
@Bruce Ageing is not for cowards! But at least the fun is back with this project so I made also good progress.

bughunter
Now some colour comes into play! I drew some masks and had them cut by the plotter.

Christoph Kunz
Happy you're back, but what the heck???
This is a speedbuild, never seen one made by you.
And it's going to be an elegant one 👍

bughunter
Yes Christoph, that was exactly the reason why I selected this kit/project from my stash! Due to my two Eduard D.IIIa I was fully aware of the kit and I know what have to be done where. For the paint I used here Alclad and Mr.Paint so I could do all the masking and painting on one afternoon 🙂 MrPaint is the "modelling turbo"!
Even the rigging is not very complicated, no crosses inside the struts, and a single-bay biplane 👍

Christian Bruer
Another masterpiece in the making 👍

Ludvík Kružík
The speed with which you have progressed on this model is admirable. The paintwork turned out great and the different shades of silver depending on the material the paint was applied to look very good.

Kyle DeHart
Beautiful progress!! You're marching your way right through this one!!

John
That is a lovely machine with a lovely scheme as well. I really do need to do a few WWI subjects. Camo was in its infancy and making a reputation seemed more important at the time so what better way than to add a garish (some would say "striking") paint job? Though, I do NOT need to add more to the stash, I will be 100+ before I finish what I have. As you note, getting older is not fun, but it's preferable to the alternative! Good to see you back. 👍

Skyhiker
Gosh, that's beautiful bughunter.

J35J
Amazing work again bughunter! You're builds are great inspiration👍🏻

bughunter
Thanks to all for your wonderful feedback!

@Ludvik That is only one thin common layer of Semi Matt Alu. The underground shines through, like a preshading.

@John There are many very nice schemes available in my Pfalz references, especially in the "Pfalz D.IIIa at war" books (I have another D.IIIa Profipack in my shash). Regarding the second kit of this Dual Combo: The six Eduard markings are nice, but I will try to replicate a beautiful blue/red four-view profile painted by Ronny Bar in the Kagero book.
Regarding camo and colorful markings: The German printed fabric known as Lozenge had to task to avoid the detection of the aircraft type from far away (blur contours). The colorful markings were needed during dog fights with many fighters for quick detection of enemy, friends and leaders, as there were no radios yet (ok, some air-to-gound radios with morse code in two seaters; but no communication between fighters).

@J35J Then I hope the further steps will fulfill your expectations!

Mr D
Nice ... very nice choice 👍👍👍 been considering one soon... Has it been a good kit ??

bughunter
Oh yes, the Eduard Pfalz D.III series are great kits! There are small things which can be fixed and I mention them in my build reports. If you click on my Pfalz Collection you can see also my other builds of this kit.
The kit has also optional parts, e.g. for the D.IIIa two lower wings in different shapes. There was also a PE sheet for the IIIa with many more nice parts than on the little Profipack PE.

Alec K
Taking a late seat. The subtle variation in aluminum color is excellent. I also like the painted-on insignia and markings 👍

Mr D
Thanks 👍👍 the kit does look really precise, will check out build,
I have an RC version from E-file, as always loved the look of the look of them..l put photo in my main Album.
Thanks for Advice 😁

bughunter
That huge RC bird looks nice, but is an Albatros and not a Pfalz 😉

Mr D
Thanks, 😃👍 calm weather flyer....looks great in the air.
Ok....your better informed on the WW1 stuff , l tend to watch vids n research an aircraft on and around the building ....for ref n learning.
It's mainly been ww2 n cold war I've built so far.
Best of luck with rest of build it's brilliant job so far.

bughunter
New pictures are uploaded with the prepared undercarriage. At first I wanted to use the kit parts, but I checked my other Pfalz in the cabinet: the legs are very flexible. In this new case my legs had also a mould offset (that is something I hate on filigree plastic parts!) so for fix this it would made the legs more weak.
As many of my newer models has metal legs now I decided to do it here too. As other advantage they are finer and looks more scale.

Ben M
Those offsets are so frustrating.

Edward MacKenzie
Thanks guys for all your likes! 😄

Moreno Baruffini
Wow! I missed for a bit this one and I just found a super progess!!!

Edward MacKenzie
Thank you very much Moreno! Too kind, but to be honest i am very happy with this progress too 😉

J35J
Looking great Edward! Following👍🏻

Oleg Bogolei
Followong!

Robert Podkoński
Interesting start. Watching for sure!

Cristian A
Me too! 😃

Sy Bar
Amazing idea and work can't wait for more 🍿

Nicolas
I grap a seat as well.

CaptGPF
🧐

Guy Rump
Following as well. 👍