Newsfeed

Rui S
Welcome to scalemates🙂

Kyle Larson
Thanks!

Greg Baker
First print mostly successful. I will need to rework the thickness of the walls and the support struts for the roof. Much too thin.

Robert Podkoński
Taking a seat here 🙂

LucLuke B
3d printing, I wouldn't know where to start. Is the ami 6 a file you found online?

Greg Baker
I did find it online, but was a little disappointed with the quality. It required a lot (and will need more) work to be able to print it. I mainly have to increase the thickness of the rear trunk area. The strange overhang roof in the rear needs to be sturdier as well.

Alex K
Can't miss this...

Greg Baker
The second printing went much better. I made a mistake though, I forgot to add the support to both sides of the rear roof struts. Luckily one side seems to be strong enough to hold everything, and with a little paint I don't think the thin part will be visible.

Cuajete
I can't miss it either.

Matthew A
Amazing printing

Alec K
Taking a seat 👍

Thomas Espe
👀

Spanjaard
i am in 🙂

Greg Baker
Good timing. After a bit of a summer break spent watching football, olympics, and playing video games with my son... I just started back at the modelling desk. After clearing up a couple of other, smaller, Tintin-related projects, I'm almost ready to tackle this one again.

Greg Baker
With the Hawker Hart off the bench and on the shelf… I guess it's time to tackle this one again. Getting the colour right was tricky. I finally settled on a 10:5:1 ratio of Tamiya XF-2 White, X-14 Sky Blue and XF-18 Medium Blue. Not perfect, but close enough I think.

Cuajete
I like this color, Greg 👍

Skyhiker
Oh, this looks like fun!

Chris Parsons
Oh ya!
Built a couple of Broplan vac kits, a real challenge but great for the feeling of overcoming a challenge and creative accomplishment

Thomas Kolb
OMG, what a challenge! 🙂 Those panel lines look quite uneven, will you try to rescribe them or just take them for what they are? In any way, I am super curious how these sheets of plastic can be turned into a model, so I will watch with interest!

DuperScale
Welcome mates, the panellines are aweful but the material is so thin, i'm scarred that i cut right trough it when i try to rescribe them.

Łukasz Gliński
Another BroPlan fan, welcome to the club 😄

Nicolas
Following. Got my first vacu kit this weekend. I hope I can learn something here.

Robert Podkoński
Ambitious project! Watching.

Chris Parsons
Hi DuperScale, I built a couple of Broplan vac ATR kits, converting one 72 500 to a 42 300. A few pics of the work in my "albums" if you're interested in the kind of model you can achieve from a Broplan kit with a bit of work…sweat and tears, foul language, alcohol and time….

Cristian A
Following along.

Michael Kohl
Mee too.

J35J
Following with intrest! 👍🏻

Finn
This will be good

Ben M
👀

Treehugger
DuperScale, how about scribing into a layer of primer paint?
This way, scribing should be a lot easier afaik, scribing into the primer layer of paing, and not plastic.
This guy on youtube did this, on regular plastic models though.

Treehugger
As for the clear parts, I wonder if it could be done this way
1) Cut out a square/rectangle shape, removing the oval form from windows. The larger the hole the better, to create some extra space around the old window shape. Enough space to work with putty later on.
2) Glue in a flat thin strip of transparent styrene on inside of model.
3) Glue in a square/rectangle shape transparent styrene, outside the model, laminated with the existing strip of transparent styrene on inside, so double layered.

If keeping the new window parts larger than the old window shape it should be easier to use some putty after adding masking tape that have the shape of the old windows. The larger these new outer square/rectangle window shapes are, the easier it is to add putty to create a smooth surface, then hopefully the center part is clear enough, to mask off the final shape of the old window shape, before painting.

Afaik a common issue using Mikro Kristal Klear is that you can't sand the clear part afterwards, because the clear part is like rubber iirc. You can iirc easily remove this clear part though, just poke/pull it out. Unsure if there would be any residue left after removing the rubber like liquid clear stuff after it dries.

Treehugger
Another thing one could do with clear parts an idea:
1) Glue in a long strip of transparent styrene on inside of plane.
2) Add some kind of epoxy or something that can be sanded, without the epoxy damaging the underlying transparent styrene.
3) Idea is to use the liquid stuff to fill in the perfectly shaped holes for the windows, then sand the liquid stuff flush after it dries.

What won't work imo, is doing multiple rounds of adding liquids to create some goo that goes transparent. I think if you sand this stuff multiple times adding more liquid stuff, you get a flawed result I think. I tried something like that with gloss varnish, trying to build up a solid clear shape. Did not work as expected.

Treehugger
In this thread, and in photo #13, the guy apparently put tape outside, and poured clear resin on the inside to fill the window holes. Unsure if such resin will react and maybe eat up or warp any thin parts ala vacuum kits. I guess this can be tested with some scrap plastic if having some piece left over.

Boeing 737-530 Smart Wings 1:144 | Album by Zbynek (1:144)

Łukasz Gliński
The UV transparent resin is usually sandable (to some degree), maybe that might help?
Similarly to Treehugger I'd reinforce it with a transparent styrene from the inside of the fuselage anyway.
Or you might leave the windows open and fill them with Kristal Klear after painting - this is what I did on my Jetstream, Avanti & Yak-40. But if you want to seal it with gloss varnish, remember to keep very thin layers (guess how I learned it 🙂).
[img1]
Blue Jetstream (SP-KWN) | Album by Woody (1:72)
Avanti! | Album by Woody (1:72)

DuperScale
Hi, thanks for the input mates. I'm quite happy with the kristal clear on the small windows and i think i do it like Lukasz said. After everything is done i do the windows as the last step.

The windscreen window could work but i think i used little to much of the kristal clear.

Mr D
Good to see a vacform 😃👍

Cuajete
Well done so far 👍

David Taylor
Watching.

J35J
Great work so far with the vac👍🏻

Mr D
Like the cockpit..👍
Lots of work but doing a 👍 job... Be rewarding when done.

Cuajete
Great (hard) job so far. Go on!