F-16CJ Block 50
![Album image #1 Album image #1](/albums/img/8/7/0/246870-21660-61-720.jpg)
This kit has aftermarket radar, cockpit, 20mm cannon, missiles, landing gear bays, wheels, airbrakes, and exhaust, That's a lot of resin!
![Album image #2 Album image #2](/albums/img/8/7/1/246871-21660-79-720.jpg)
The Hasegawa design has some major improvements over the Academy one, particularly in the wing root and rear fuselage areas.
![Album image #3 Album image #3](/albums/img/8/7/2/246872-21660-93-720.jpg)
AN/APG-66 Radar from Czech Master Kits. I added the wires myself after noticing them in a number of reference photos.
![Album image #4 Album image #4](/albums/img/8/7/3/246873-21660-93-720.jpg)
The canopy tint really stands out in this picture.
![Album image #5 Album image #5](/albums/img/8/7/4/246874-21660-54-720.jpg)
The missiles are from the Hasegawa Weapons kit C and D, and marked using decals from TwoBobs
![Album image #6 Album image #6](/albums/img/8/7/5/246875-21660-53-720.jpg)
The afterburner was a very challenging item to paint both inside and out. The uneven exhaust stains are due to the radial spacing of the fuel injector nozzles.
![Album image #7 Album image #7](/albums/img/8/7/6/246876-21660-79-720.jpg)
The Aires airbrakes are nothing short of perfect. The basic kit's level of detail pales in comparison to these highly accurate brass and resin pieces.
![Album image #8 Album image #8](/albums/img/8/7/7/246877-21660-96-720.jpg)
The markings are for a ship in the 20th Fighter Wing, Air Combat Command, based out of Shaw AFB, in South Carolina.
![Album image #9 Album image #9](/albums/img/8/7/8/246878-21660-46-720.jpg)
This shot gives you a good look at the interior of the exhaust assembly. The detail of the afterburner is just top notch, especially since the "tiled" surface of the part is replicated in minute detail. So minute, in fact, it can't be fabricated using tra
![Album image #10 Album image #10](/albums/img/8/7/9/246879-21660-36-720.jpg)
![Album image #11 Album image #11](/albums/img/8/8/0/246880-21660-75-720.jpg)
Wheels from AIRES "Wheeliant" series.
![Album image #12 Album image #12](/albums/img/8/8/1/246881-21660-62-720.jpg)
The gold tint on the canopy was added by airbrushing a thin coat of Holbein acrylic paint. Also, note the scratch built grab bars fabricated from copper wire.
![Album image #13 Album image #13](/albums/img/8/8/2/246882-21660-92-720.jpg)
Airbrakes and afterburner provided by AIRES.
![Album image #14 Album image #14](/albums/img/8/8/3/246883-21660-46-720.jpg)
20mm cannon from CMK.
![Album image #15 Album image #15](/albums/img/8/8/4/246884-21660-30-720.jpg)
I'm very very proud of my intake fan even though it's essentially hidden from view. Look at those turbine blades!
![Album image #16 Album image #16](/albums/img/8/8/5/246885-21660-23-720.jpg)
The photo etched brass radar dish is an excellent approximation of the real thing. A single coat of tan paint worked out decently well in my case, but I'm going to try for a more realistic glossy finish on the next one I build.
![Album image #17 Album image #17](/albums/img/8/8/6/246886-21660-16-720.jpg)
![Album image #18 Album image #18](/albums/img/8/8/7/246887-21660-77-720.jpg)
Kommentare
26 March 2016, 18:58