MyAlbum: S.M. Unterseeboot U9 Class - U-9
![Album image #1 Album image #1](/albums/img/1/6/9/1155169-106039-18-720.jpg)
2 in 1.
S.M. U-9 and CV 707 VESIKKO.
S.M. U-9 and CV 707 VESIKKO.
![Album image #2 Album image #2](/albums/img/1/7/0/1155170-106039-31-720.jpg)
Inside Box
![Album image #3 Album image #3](/albums/img/1/7/1/1155171-106039-73-720.jpg)
NOTE:
The thickness of the keel of the ship's nose is wrong, it must be filed/sanded!
The thickness of the keel of the ship's nose is wrong, it must be filed/sanded!
![Album image #4 Album image #4](/albums/img/1/7/2/1155172-106039-75-720.jpg)
The thickness of the keel of the ship's nose is wrong, it must be filed/sanded!
![Album image #5 Album image #5](/albums/img/1/7/3/1155173-106039-69-720.jpg)
The thickness of the keel of the ship's bow is incorrect, it must be filed/sanded thinner!
Viewed from the Keel side of the Ship:
Upper Side- corrected.
Bottom Side - the part that needs to be removed is marked.
Viewed from the Keel side of the Ship:
Upper Side- corrected.
Bottom Side - the part that needs to be removed is marked.
![Album image #6 Album image #6](/albums/img/1/7/4/1155174-106039-62-720.jpg)
The thickness of the keel of the ship's bow is incorrect, it must be filed/sanded thinner!
Looking from the Ship's Deck Side:
Upper Side - the part that needs to be removed is marked.
Bottom Side - corrected.
Looking from the Ship's Deck Side:
Upper Side - the part that needs to be removed is marked.
Bottom Side - corrected.
![Album image #7 Album image #7](/albums/img/1/7/5/1155175-106039-36-720.jpg)
The thickness of the keel of the ship's bow is incorrect, it must be filed/sanded thinner!
Looking from the Ship's Deck Side:
Upper Side - the part that needs to be removed is marked.
Bottom Side - corrected.
Looking from the Ship's Deck Side:
Upper Side - the part that needs to be removed is marked.
Bottom Side - corrected.
![Album image #8 Album image #8](/albums/img/1/7/6/1155176-106039-71-720.jpg)
The correct fixing of the hull halves of the ship and the correctness of the resulting external joint surface.
The parts have internal stresses, one side of the hull is twisted and bent in one direction, the other side of the hull is facing the other way, and in the end result, the visible displacements of the hull sides remain on the outer surface. The outer surface has a detailed geometry and rivet pattern that cannot be over-sanded for correction and repair. This will ruin all that beautiful finished surface!
The correct fixing of the hull halves of the ship with each other with 8 pins (lower half) is not enough, additional surfaces must be added here, which ensure the correct positioning of the joint surfaces of the hull.
The parts have internal stresses, one side of the hull is twisted and bent in one direction, the other side of the hull is facing the other way, and in the end result, the visible displacements of the hull sides remain on the outer surface. The outer surface has a detailed geometry and rivet pattern that cannot be over-sanded for correction and repair. This will ruin all that beautiful finished surface!
The correct fixing of the hull halves of the ship with each other with 8 pins (lower half) is not enough, additional surfaces must be added here, which ensure the correct positioning of the joint surfaces of the hull.
![Album image #9 Album image #9](/albums/img/1/7/7/1155177-106039-64-720.jpg)
![Album image #10 Album image #10](/albums/img/1/7/8/1155178-106039-41-720.jpg)
NOTE:
The 3 + 3 plates of the ship's deck and ship's hull do not stay correctly, the deck must be brought forward approx. 1 mm in order to align the "joints" of the plates.
The 3 + 3 plates of the ship's deck and ship's hull do not stay correctly, the deck must be brought forward approx. 1 mm in order to align the "joints" of the plates.
![Album image #11 Album image #11](/albums/img/1/7/9/1155179-106039-19-720.jpg)
In order to see how the parts fit together, the ship needs to be "assembled dry".
And here comes a series of surprises.
1. The thickness of the ship's nose keel is incorrect (3 mm on the model, it must be at least 0.5 mm.
2. The Deck of the Ship is short, the sections of the 3 + 3 panels of the first part do not run together, and the gap is about 1mm.
3. Height-depth controls - 3 positions!?, which ones are in use?
4. The correct fixing of the hull halves of the ship and the correctness of the resulting external joint surface.
The parts have internal stresses, one side of the hull is twisted and bent in one direction, the other side of the hull is facing the other way, and in the end result, the visible displacements of the hull sides remain on the outer surface. The outer surface has a detailed geometry and rivet pattern that cannot be over-sanded for correction and repair. This will ruin all that beautiful finished surface!
The correct fixing of the hull halves of the ship with each other with 8 pins (lower half) is not enough, additional surfaces must be added here, which ensure the correct positioning of the joint surfaces of the hull.
5. If you want to look at the ship from below, the base included with the model (the ship's pedestal) does not allow this, the ship is too low from the surface. The base could raise the ship a little higher.
And here comes a series of surprises.
1. The thickness of the ship's nose keel is incorrect (3 mm on the model, it must be at least 0.5 mm.
2. The Deck of the Ship is short, the sections of the 3 + 3 panels of the first part do not run together, and the gap is about 1mm.
3. Height-depth controls - 3 positions!?, which ones are in use?
4. The correct fixing of the hull halves of the ship and the correctness of the resulting external joint surface.
The parts have internal stresses, one side of the hull is twisted and bent in one direction, the other side of the hull is facing the other way, and in the end result, the visible displacements of the hull sides remain on the outer surface. The outer surface has a detailed geometry and rivet pattern that cannot be over-sanded for correction and repair. This will ruin all that beautiful finished surface!
The correct fixing of the hull halves of the ship with each other with 8 pins (lower half) is not enough, additional surfaces must be added here, which ensure the correct positioning of the joint surfaces of the hull.
5. If you want to look at the ship from below, the base included with the model (the ship's pedestal) does not allow this, the ship is too low from the surface. The base could raise the ship a little higher.
![Album image #12 Album image #12](/albums/img/1/8/0/1155180-106039-25-720.jpg)
![Album image #13 Album image #13](/albums/img/1/8/1/1155181-106039-65-720.jpg)
![Album image #14 Album image #14](/albums/img/1/8/2/1155182-106039-85-720.jpg)
![Album image #15 Album image #15](/albums/img/1/8/3/1155183-106039-13-720.jpg)
![Album image #16 Album image #16](/albums/img/1/8/4/1155184-106039-18-720.jpg)
![Album image #17 Album image #17](/albums/img/1/8/8/1155188-106039-75-720.jpg)
There is already not enough free space left.
![Album image #18 Album image #18](/albums/img/1/8/9/1155189-106039-18-720.jpg)
Correct and detailed Machine Guns for Ships - Schwarzlose 07/12 Navale.
GasPatch Models 72219,
GasPatch Models 72219,
![Album image #19 Album image #19](/albums/img/1/9/0/1155190-106039-59-720.jpg)
Priming of Chimney and Deck Details.
![Album image #20 Album image #20](/albums/img/1/9/1/1155191-106039-39-720.jpg)
Photoetching makes the image flicker before the eyes. 😉
![Album image #21 Album image #21](/albums/img/1/9/2/1155192-106039-39-720.jpg)
Bringing the deck forward 1 mm, after that, the side panels (3 + 3 Sections) in the nose fit correctly in place.
![Album image #22 Album image #22](/albums/img/1/9/3/1155193-106039-79-720.jpg)
Bringing the deck forward 1 mm, after that, the side panels (3 + 3 Sections) in the nose fit correctly in place.
![Album image #23 Album image #23](/albums/img/1/9/4/1155194-106039-21-720.jpg)
After bringing the ship's deck forward by 1 mm, a 1 mm strip has been added to the ship's deck, in addition, styrene support has been added below the new joint of the deck. To obtain the correct flatness of the joint surfaces of the deck.
![Album image #24 Album image #24](/albums/img/1/9/5/1155195-106039-90-720.jpg)
Ship's nose keel after grinding thinner.
![Album image #25 Album image #25](/albums/img/1/9/6/1155196-106039-84-720.jpg)
Ship's nose keel after grinding thinner.
![Album image #26 Album image #26](/albums/img/1/9/7/1155197-106039-98-720.jpg)
Ship's nose keel after grinding thinner and bringing the deck forward 1 mm.
After that, the side panels in the nose fit correctly in place.
After that, the side panels in the nose fit correctly in place.
![Album image #27 Album image #27](/albums/img/1/9/8/1155198-106039-84-720.jpg)
After bringing the ship's deck forward by 1 mm, a 1 mm strip has been added to the ship's deck, in addition, styrene support has been added below the new joint of the deck. To obtain the correct flatness of the joint surfaces of the deck (White Details on the Top).
![Album image #28 Album image #28](/albums/img/1/9/9/1155199-106039-19-720.jpg)
3D Printed Chimney Section.
![Album image #29 Album image #29](/albums/img/2/0/0/1155200-106039-89-720.jpg)
The Ship's nose keel after being sanded down and prepared for the addition of photoetched details.
![Album image #30 Album image #30](/albums/img/2/0/1/1155201-106039-16-720.jpg)
The Keel of the Ship's Nose after grinding it thinner and installing the Photoetched Parts.
![Album image #31 Album image #31](/albums/img/2/0/2/1155202-106039-79-720.jpg)
The Keel of the Ship's Nose after grinding it thinner and installing the Photoetched Parts.
![Album image #32 Album image #32](/albums/img/2/0/3/1155203-106039-92-720.jpg)
After bringing the ship's deck forward by 1 mm, a 1 mm strip has been added to the ship's deck, in addition, styrene support has been added below the new joint of the deck. To obtain the correct flatness of the joint surfaces of the deck (White Details in Bow Deck Section Ends).
![Album image #33 Album image #33](/albums/img/2/0/4/1155204-106039-35-720.jpg)
3D Printed Chimney Section assembled on the Deck.
![Album image #34 Album image #34](/albums/img/2/0/5/1155205-106039-89-720.jpg)
3D Printed Chimney Section assembled on the Deck.
The chimney section can be turned to the upper position or hidden in the deck when lowered.
The chimney section can be turned to the upper position or hidden in the deck when lowered.
![Album image #35 Album image #35](/albums/img/2/0/6/1155206-106039-11-720.jpg)
Preparation of photoetched parts for installation.
![Album image #36 Album image #36](/albums/img/2/0/7/1155207-106039-91-720.jpg)
Marking down the locations of the photo-etched parts on the hull according to the drawing.
![Album image #37 Album image #37](/albums/img/2/0/8/1155208-106039-45-720.jpg)
Marking down the locations of the photo-etched parts on the hull according to the drawing.
![Album image #38 Album image #38](/albums/img/2/0/9/1155209-106039-67-720.jpg)
Installation of photoetched parts.
![Album image #39 Album image #39](/albums/img/2/1/0/1155210-106039-21-720.jpg)
Installation of photoetched parts in the Ship Hull.
![Album image #40 Album image #40](/albums/img/2/1/1/1155211-106039-70-720.jpg)
Installation of photoetched parts.
![Album image #41 Album image #41](/albums/img/2/1/2/1155212-106039-50-720.jpg)
Installation of photoetched parts.
![Album image #42 Album image #42](/albums/img/2/1/3/1155213-106039-34-720.jpg)
![Album image #43 Album image #43](/albums/img/2/1/4/1155214-106039-58-720.jpg)
![Album image #44 Album image #44](/albums/img/2/1/5/1155215-106039-91-720.jpg)
Preparation of fasteners for radio masts and making the necessary openings in the ship's hull.
![Album image #45 Album image #45](/albums/img/2/1/6/1155216-106039-74-720.jpg)
Preparation of fasteners for radio masts and making the necessary openings in the ship's hull.
![Album image #46 Album image #46](/albums/img/2/1/7/1155217-106039-78-720.jpg)
Preparation of fasteners for radio masts and making the necessary openings in the ship's hull. Photoetched part Installation on the place.
![Album image #47 Album image #47](/albums/img/2/1/8/1155218-106039-38-720.jpg)
Preparation of fasteners for radio masts and making the necessary openings in the ship's hull. Photoetched part Installation on the place.
![Album image #48 Album image #48](/albums/img/2/1/9/1155219-106039-39-720.jpg)
Preparation of fasteners for radio masts and making the necessary openings in the ship's hull.
![Album image #49 Album image #49](/albums/img/2/2/0/1155220-106039-74-720.jpg)
![Album image #50 Album image #50](/albums/img/2/2/1/1155221-106039-27-720.jpg)
Assembling the Radio Masts Modules and Photo Etched Parts.
![Album image #51 Album image #51](/albums/img/2/2/2/1155222-106039-93-720.jpg)
Radio Masts Modules.
![Album image #52 Album image #52](/albums/img/2/2/3/1155223-106039-55-720.jpg)
Radio Mast Module. The mast can be rotated around its rotation pair, the mast can be raised and lowered onto the ship's deck.
![Album image #53 Album image #53](/albums/img/2/2/4/1155224-106039-98-720.jpg)
Radio Masts Modules.
![Album image #54 Album image #54](/albums/img/2/2/5/1155225-106039-78-720.jpg)
Radio Mast Base Module installation on the Deck.
![Album image #55 Album image #55](/albums/img/2/2/6/1155226-106039-84-720.jpg)
Radio Mast Base Module.
![Album image #56 Album image #56](/albums/img/2/2/7/1155227-106039-45-720.jpg)
Assembled and Installed Radio Mast Module.
![Album image #57 Album image #57](/albums/img/2/2/8/1155228-106039-14-720.jpg)
Assembled and Installed Radio Mast Module.
![Album image #58 Album image #58](/albums/img/2/2/9/1155229-106039-16-720.jpg)
Assembled and Installed Radio Mast Module.
![Album image #59 Album image #59](/albums/img/2/3/0/1155230-106039-30-720.jpg)
Both Radio Masts Modules on the Place.
![Album image #60 Album image #60](/albums/img/2/3/1/1155231-106039-99-720.jpg)
Radio Mast Module.
![Album image #61 Album image #61](/albums/img/2/3/2/1155232-106039-80-720.jpg)
Deck Installation on the Ship Hull.
![Album image #62 Album image #62](/albums/img/2/3/3/1155233-106039-86-720.jpg)
Deck Installed on the Ship Hull.
![Album image #63 Album image #63](/albums/img/2/3/4/1155234-106039-89-720.jpg)
The Ship's Hull and both Deck Sections are together.
![Album image #64 Album image #64](/albums/img/2/3/5/1155235-106039-76-720.jpg)
![Album image #65 Album image #65](/albums/img/2/3/9/1155239-106039-98-720.jpg)
![Album image #66 Album image #66](/albums/img/2/4/0/1155240-106039-93-720.jpg)
![Album image #67 Album image #67](/albums/img/2/4/1/1155241-106039-78-720.jpg)
![Album image #68 Album image #68](/albums/img/2/4/2/1155242-106039-46-720.jpg)
Installation of photoetched parts.
![Album image #69 Album image #69](/albums/img/2/4/3/1155243-106039-55-720.jpg)
Installation of photoetched parts.
![Album image #70 Album image #70](/albums/img/2/4/4/1155244-106039-24-720.jpg)
Preparation of photoetched parts for installation.
![Album image #71 Album image #71](/albums/img/2/4/5/1155245-106039-53-720.jpg)
Preparation of photoetched parts for installation.
![Album image #72 Album image #72](/albums/img/2/4/6/1155246-106039-35-720.jpg)
In the meantime, you have to check the manual for the sequel. 😉
![Album image #73 Album image #73](/albums/img/2/4/7/1155247-106039-88-720.jpg)
With additions to the bow of the ship.
![Album image #74 Album image #74](/albums/img/2/4/8/1155248-106039-81-720.jpg)
Details.
![Album image #75 Album image #75](/albums/img/2/4/9/1155249-106039-55-720.jpg)
Legend: 9 x measure, 1 x cut!
![Album image #76 Album image #76](/albums/img/2/5/0/1155250-106039-74-720.jpg)
Details and their additions: Searchlight and machine gun base.
![Album image #77 Album image #77](/albums/img/2/5/1/1155251-106039-12-720.jpg)
Details and their additions: Searchlight and machine gun base.
![Album image #78 Album image #78](/albums/img/2/5/2/1155252-106039-15-720.jpg)
Drawings, Details and their additions: Searchlight and machine gun base.
![Album image #79 Album image #79](/albums/img/2/5/3/1155253-106039-35-720.jpg)
A machine gun on its base on the ship's deck.
![Album image #80 Album image #80](/albums/img/2/5/4/1155254-106039-55-720.jpg)
Details and their additions: Searchlight Assembling.
![Album image #81 Album image #81](/albums/img/2/5/5/1155255-106039-52-720.jpg)
A machine gun on its base on the ship's deck.
![Album image #82 Album image #82](/albums/img/2/5/6/1155256-106039-65-720.jpg)
A machine gun on its base on the ship's deck.
![Album image #83 Album image #83](/albums/img/2/5/7/1155257-106039-68-720.jpg)
Details and their additions: Searchlight Assembling.
![Album image #84 Album image #84](/albums/img/2/5/8/1155258-106039-83-720.jpg)
![Album image #85 Album image #85](/albums/img/2/5/9/1155259-106039-95-720.jpg)
Drilling Jig made from Styrene Plate.
![Album image #86 Album image #86](/albums/img/2/6/0/1155260-106039-43-720.jpg)
Photo Etched Part and Jigs.
![Album image #87 Album image #87](/albums/img/2/6/1/1155261-106039-24-720.jpg)
Photo Etched Part and Drilling Jig 2.
![Album image #88 Album image #88](/albums/img/2/6/2/1155262-106039-30-720.jpg)
Drilling Jig 2, Drilled Deck Section, and Photo Etched Deck Part.
![Album image #89 Album image #89](/albums/img/2/6/3/1155263-106039-62-720.jpg)
Drilling Jig 2, Drilled Deck Section, and Photo Etched Deck Part.
![Album image #90 Album image #90](/albums/img/2/6/4/1155264-106039-75-720.jpg)
Drilling Jig 2, Drilled Deck Section, and Photo Etched Deck Part.
![Album image #91 Album image #91](/albums/img/2/6/5/1155265-106039-96-720.jpg)
Photo Etched Deck Part on the Position.
![Album image #92 Album image #92](/albums/img/2/6/6/1155266-106039-82-720.jpg)
Drilling Jig 1 on the Position.
![Album image #93 Album image #93](/albums/img/2/6/7/1155267-106039-14-720.jpg)
Photo Etched Deck Part on the Position.
![Album image #94 Album image #94](/albums/img/2/6/8/1155268-106039-82-720.jpg)
Photo Etched Deck and Hull Parts.
![Album image #95 Album image #95](/albums/img/2/6/9/1155269-106039-19-720.jpg)
Photo Etched Deck and Hull Parts in Stern Part of a Ship.
![Album image #96 Album image #96](/albums/img/2/7/0/1155270-106039-68-720.jpg)
Photo Etched Deck and Hull Parts in Bow Part of a Ship.
![Album image #97 Album image #97](/albums/img/2/7/1/1155271-106039-16-720.jpg)
Photo Etched Deck and Hull Parts in Bow Part of a Ship.
![Album image #98 Album image #98](/albums/img/2/7/2/1155272-106039-92-720.jpg)
Photo Etched Deck and Hull Parts in Stern Part of a Ship.
![Album image #99 Album image #99](/albums/img/2/7/3/1155273-106039-55-720.jpg)
Major "sheet metal works" have been completed! 😉
![Album image #100 Album image #100](/albums/img/2/7/4/1155274-106039-30-720.jpg)
Overview of "sheet metal work".
![Album image #101 Album image #101](/albums/img/2/7/5/1155275-106039-93-720.jpg)
0,3 mm Hole Drilling.
![Album image #102 Album image #102](/albums/img/2/7/6/1155276-106039-13-720.jpg)
Radio Mast Construction:
Changes in the drawing of the radio mast and in the details-knots, which were introduced by studying old photos in detail!
The detail is NOT an "S" but is TRIANGULAR!
Changes in the drawing of the radio mast and in the details-knots, which were introduced by studying old photos in detail!
The detail is NOT an "S" but is TRIANGULAR!
![Album image #103 Album image #103](/albums/img/2/7/7/1155277-106039-98-720.jpg)
Radio Mast Detail: The detail is NOT an "S" but is TRIANGULAR!
![Album image #104 Album image #104](/albums/img/2/7/8/1155278-106039-82-720.jpg)
Radio Mast has been raised in Working Position.
![Album image #105 Album image #105](/albums/img/2/7/9/1155279-106039-73-720.jpg)
The Radio Mast has been lowered to the Deck.
![Album image #106 Album image #106](/albums/img/2/8/0/1155280-106039-87-720.jpg)
Radio Masts both are in Working Position.
![Album image #107 Album image #107](/albums/img/2/8/1/1155281-106039-38-720.jpg)
Radio Mast.
![Album image #108 Album image #108](/albums/img/2/8/2/1155282-106039-69-720.jpg)
Details in Focus.
![Album image #109 Album image #109](/albums/img/2/8/3/1155283-106039-65-720.jpg)
The radio mast is in the lowering position, Stern Part of a Ship.
![Album image #110 Album image #110](/albums/img/2/8/4/1155284-106039-70-720.jpg)
The Radio Mast is lowering Position, Starn Part of a Ship.
![Album image #111 Album image #111](/albums/img/2/8/5/1155285-106039-37-720.jpg)
The Radio Mast is lowering Position, Bow Part of a Ship.
![Album image #112 Album image #112](/albums/img/2/8/6/1155286-106039-54-720.jpg)
![Album image #113 Album image #113](/albums/img/2/8/7/1155287-106039-10-720.jpg)
![Album image #114 Album image #114](/albums/img/2/8/8/1155288-106039-28-720.jpg)
![Album image #115 Album image #115](/albums/img/2/8/9/1155289-106039-16-720.jpg)
![Album image #116 Album image #116](/albums/img/2/9/0/1155290-106039-82-720.jpg)
![Album image #117 Album image #117](/albums/img/2/9/1/1155291-106039-12-720.jpg)
Deck Details.
![Album image #118 Album image #118](/albums/img/2/9/2/1155292-106039-79-720.jpg)
![Album image #119 Album image #119](/albums/img/2/9/3/1155293-106039-82-720.jpg)
Comano Tower.
![Album image #120 Album image #120](/albums/img/2/9/4/1155294-106039-66-720.jpg)
Comano Tower Details.
![Album image #121 Album image #121](/albums/img/2/9/5/1155295-106039-42-720.jpg)
Comano Tower Photo Etched Details Forming.
![Album image #122 Album image #122](/albums/img/2/9/6/1155296-106039-34-720.jpg)
Comano Tower Details.
![Album image #123 Album image #123](/albums/img/2/9/7/1155297-106039-91-720.jpg)
Comano Tower Installation.
![Album image #124 Album image #124](/albums/img/2/9/8/1155298-106039-45-720.jpg)
Comano Tower.
![Album image #125 Album image #125](/albums/img/2/9/9/1155299-106039-80-720.jpg)
Update Kit: Navy Machine Guns - Schwarzlose 07/12 Navale - from GasPatch Models (72219).
![Album image #126 Album image #126](/albums/img/3/0/0/1155300-106039-47-720.jpg)
Update Kit: Navy Machine Guns - Schwarzlose 07/12 Navale.
![Album image #127 Album image #127](/albums/img/3/0/1/1155301-106039-83-720.jpg)
![Album image #128 Album image #128](/albums/img/3/0/2/1155302-106039-45-720.jpg)
Height rudders - what position to leave, what positions to take:
Top - Middle;
Middle - Lower;
Top - Lower?
Top - Middle;
Middle - Lower;
Top - Lower?
![Album image #129 Album image #129](/albums/img/3/0/3/1155303-106039-93-720.jpg)
![Album image #130 Album image #130](/albums/img/0/1/4/1156014-106039-53-720.jpg)
Ship Machine Gun Position in the Deck, Stern Part.
![Album image #131 Album image #131](/albums/img/0/1/5/1156015-106039-43-720.jpg)
The Ship's Deck Superstructure, Command Tower, and Railing Piles have been installed.
![Album image #132 Album image #132](/albums/img/0/1/6/1156016-106039-76-720.jpg)
The Ship's Deck Superstructure, Command Tower, and Railing Piles have been installed.
![Album image #133 Album image #133](/albums/img/0/1/7/1156017-106039-76-720.jpg)
The Ship's Deck Superstructure, Command Tower, and Railing Piles have been installed.
![Album image #134 Album image #134](/albums/img/0/1/8/1156018-106039-36-720.jpg)
Command Tower and Details.
![Album image #135 Album image #135](/albums/img/0/1/9/1156019-106039-67-720.jpg)
The Ship's Deck Superstructure, Command Tower, and Railing Piles have been installed.
![Album image #136 Album image #136](/albums/img/0/2/0/1156020-106039-63-720.jpg)
Machine Gun in the Stern Part of the Ship.
![Album image #137 Album image #137](/albums/img/0/2/1/1156021-106039-74-720.jpg)
Command Tower, Searchlight, and Radio Systems.
![Album image #138 Album image #138](/albums/img/0/2/2/1156022-106039-12-720.jpg)
Preassembled Submarine Model Inspection. Ready for Paint Work.
![Album image #139 Album image #139](/albums/img/0/2/3/1156023-106039-84-720.jpg)
Preassembled Submarine Model. Ready for Paint Work.
![Album image #140 Album image #140](/albums/img/0/2/4/1156024-106039-37-720.jpg)
Preassembled Submarine Model. Ready for Paint Work.
![Album image #141 Album image #141](/albums/img/0/2/5/1156025-106039-13-720.jpg)
Preassembled Submarine Model. Ready for Paint Work.
![Album image #142 Album image #142](/albums/img/0/2/6/1156026-106039-40-720.jpg)
Preassembled Submarine Model, Top View, Ready for Paint Work.
![Album image #143 Album image #143](/albums/img/0/2/7/1156027-106039-54-720.jpg)
Preassembled Submarine Model. Ready for Paint Work.
![Album image #144 Album image #144](/albums/img/0/2/8/1156028-106039-81-720.jpg)
Railing Details preparation.
![Album image #145 Album image #145](/albums/img/0/2/9/1156029-106039-29-720.jpg)
Railing Details preparation.
![Album image #146 Album image #146](/albums/img/0/3/0/1156030-106039-78-720.jpg)
Railing Details.
![Album image #147 Album image #147](/albums/img/0/3/1/1156031-106039-12-720.jpg)
Railing Details Installation.
![Album image #148 Album image #148](/albums/img/0/3/2/1156032-106039-97-720.jpg)
Machine Guns and Searchlight Stands are Painted and Finished w Varnished.
![Album image #149 Album image #149](/albums/img/0/3/3/1156033-106039-20-720.jpg)
Railing details are in place.
![Album image #150 Album image #150](/albums/img/0/3/4/1156034-106039-15-720.jpg)
Radio Systems in Deck.
![Album image #151 Album image #151](/albums/img/0/3/5/1156035-106039-15-720.jpg)
Deck Railing Details.
![Album image #152 Album image #152](/albums/img/0/3/6/1156036-106039-84-720.jpg)
Searchlight in Command Tower.
![Album image #153 Album image #153](/albums/img/0/3/7/1156037-106039-49-720.jpg)
Command Tower.
![Album image #154 Album image #154](/albums/img/0/3/8/1156038-106039-51-720.jpg)
Command Tower Details.
![Album image #155 Album image #155](/albums/img/0/3/9/1156039-106039-90-720.jpg)
Preassembled Submarine Model. Ready for Paint Work.
![Album image #156 Album image #156](/albums/img/0/4/0/1156040-106039-21-720.jpg)
Machine Gun Position, Bow Part of Ship.
![Album image #157 Album image #157](/albums/img/0/4/1/1156041-106039-16-720.jpg)
Command Tower Details.
![Album image #158 Album image #158](/albums/img/0/4/2/1156042-106039-42-720.jpg)
Command Tower Details.
![Album image #159 Album image #159](/albums/img/0/4/3/1156043-106039-76-720.jpg)
Command Tower Details.
![Album image #160 Album image #160](/albums/img/4/3/7/1184437-106039-23-720.jpg)
Searching for a suitable alternative basis concept for the model:
Carriers (made of Styrene Plates).
Carriers (made of Styrene Plates).
![Album image #161 Album image #161](/albums/img/4/3/8/1184438-106039-76-720.jpg)
Searching for a suitable alternative basis concept for the model:
Skcetching, Drawings, and Part Section Samples.
Skcetching, Drawings, and Part Section Samples.
![Album image #162 Album image #162](/albums/img/4/3/9/1184439-106039-41-720.jpg)
Searching for a suitable alternative basis concept for the model:
Sketching, Drawings, and Part Section Samples.
Sketching, Drawings, and Part Section Samples.
![Album image #163 Album image #163](/albums/img/4/4/0/1184440-106039-34-720.jpg)
Searching for a suitable alternative basis concept for the model:
Sketching, Drawings, and Part Section Samples.
Sketching, Drawings, and Part Section Samples.
![Album image #164 Album image #164](/albums/img/4/4/1/1184441-106039-81-720.jpg)
Searching for a suitable alternative basis concept for the model:
Part Section Samples.
Part Section Samples.
![Album image #165 Album image #165](/albums/img/4/4/2/1184442-106039-16-720.jpg)
Searching for a suitable alternative basis concept for the model:
Part Section Samples.
Part Section Samples.
![Album image #166 Album image #166](/albums/img/4/4/3/1184443-106039-92-720.jpg)
Searching for a suitable alternative basis concept for the model:
Part Section Samples.
Part Section Samples.
![Album image #167 Album image #167](/albums/img/4/4/4/1184444-106039-18-720.jpg)
Searching for a suitable alternative basis concept for the model:
Together Gluing Sections.
Together Gluing Sections.
![Album image #168 Album image #168](/albums/img/4/4/5/1184445-106039-25-720.jpg)
Searching for a suitable alternative basis concept for the model:
Together Gluing Sections.
Together Gluing Sections.
![Album image #169 Album image #169](/albums/img/4/4/6/1184446-106039-16-720.jpg)
Searching for a suitable alternative basis concept for the model:
Together Gluing Sections.
Together Gluing Sections.
![Album image #170 Album image #170](/albums/img/4/4/7/1184447-106039-22-720.jpg)
Searching for a suitable alternative basis concept for the model:
Together Gluing Sections in Base.
Note: Lover Base Dimensions (Diameter) are too small!
Needed Action: For a specific model, the dimensions of the base must be increased to get the proportions in the right relationship.
Together Gluing Sections in Base.
Note: Lover Base Dimensions (Diameter) are too small!
Needed Action: For a specific model, the dimensions of the base must be increased to get the proportions in the right relationship.
![Album image #171 Album image #171](/albums/img/4/4/8/1184448-106039-18-720.jpg)
Searching for a suitable alternative basis concept for the model:
Ready Model Pedestal (Bow Bearer) and Sketch and Drawings for the Stern Carrier.
Ready Model Pedestal (Bow Bearer) and Sketch and Drawings for the Stern Carrier.
![Album image #172 Album image #172](/albums/img/4/4/9/1184449-106039-24-720.jpg)
Searching for a suitable alternative basis concept for the model:
Ready Model Pedestal (Bow Bearer).
Ready Model Pedestal (Bow Bearer).
![Album image #173 Album image #173](/albums/img/4/5/0/1184450-106039-60-720.jpg)
Searching for a suitable alternative basis concept for the model:
The Stern Carrier Section Marked in the Styrene Plate.
The Stern Carrier Section Marked in the Styrene Plate.
![Album image #174 Album image #174](/albums/img/4/5/1/1184451-106039-55-720.jpg)
Searching for a suitable alternative basis concept for the model:
Assembled and Glued Stern Carrier Section.
Assembled and Glued Stern Carrier Section.
![Album image #175 Album image #175](/albums/img/4/5/2/1184452-106039-76-720.jpg)
Searching for a suitable alternative basis concept for the model:
Stern Carrier Geometry Inspection with the Geometry of the Ship's Hull.
Stern Carrier Geometry Inspection with the Geometry of the Ship's Hull.
![Album image #176 Album image #176](/albums/img/4/5/3/1184453-106039-45-720.jpg)
Searching for a suitable alternative basis concept for the model:
The Shape and Geometry of the Carrier are Ground according to the Hull of the Ship.
INSTRUCTION:
Use MIRKA sandpaper (Sandpaper Mirka Abranet Ace; 70x198 mm) for processing:
P180 for preliminary work and P320 for finishing!
The fabric side is against the hull of the ship and the abrasive coated side is on the outside!
Grinding movements - along the ship's keel, from the location of the carriers. Check the resulting joint surface!
The Shape and Geometry of the Carrier are Ground according to the Hull of the Ship.
INSTRUCTION:
Use MIRKA sandpaper (Sandpaper Mirka Abranet Ace; 70x198 mm) for processing:
P180 for preliminary work and P320 for finishing!
The fabric side is against the hull of the ship and the abrasive coated side is on the outside!
Grinding movements - along the ship's keel, from the location of the carriers. Check the resulting joint surface!
![Album image #177 Album image #177](/albums/img/4/5/4/1184454-106039-93-720.jpg)
Searching for a suitable alternative basis concept for the model:
Standard Model Pedestal (from Das Werk) versus 3D Printed Base (SLS, PA-12, White) and Carriers (made of Styrene Plates).
Standard Model Pedestal (from Das Werk) versus 3D Printed Base (SLS, PA-12, White) and Carriers (made of Styrene Plates).
![Album image #178 Album image #178](/albums/img/3/3/2/1202332-106039-47-720.jpg)
3D Model of The Ship's Stern Carrier.
![Album image #179 Album image #179](/albums/img/3/3/3/1202333-106039-30-720.jpg)
Different Pedestals Concept Ideas in 3D CAD Models Library
(by COBOTEC GROUP LTD.).
(by COBOTEC GROUP LTD.).
![Album image #180 Album image #180](/albums/img/3/3/4/1202334-106039-62-720.jpg)
Choice of Different Pedestals Concept Ideas in 3D CAD Models Library
(by COBOTEC GROUP LTD.).
(by COBOTEC GROUP LTD.).
![Album image #181 Album image #181](/albums/img/3/3/5/1202335-106039-79-720.jpg)
3D Model of the Ship's Bow bearer, (M8x1,25)
![Album image #182 Album image #182](/albums/img/4/4/6/1202446-106039-43-720.jpg)
U-BOOTE, Top to bottom:
Top: S.M. U-9 (1/72);
and waiting for their sequel:
Type XXI, U2540 (1/144);
Type VII C, (U82) (1/144);
Type 212A, S 182 (1/144).
Top: S.M. U-9 (1/72);
and waiting for their sequel:
Type XXI, U2540 (1/144);
Type VII C, (U82) (1/144);
Type 212A, S 182 (1/144).
![Album image #183 Album image #183](/albums/img/4/6/9/1298469-106039-97-720.jpg)
3D Printed Model Pedestals.
Dimension: D = 60 mm; H = 80 mm.
COBOTEC GROU LTD., Model Ship Display Pedestal Kit CTG-A001410_V0_R0;
Process/Printing Technology: HP Multi Jet Fusion,
Material: PA-12.
Dimension: D = 60 mm; H = 80 mm.
COBOTEC GROU LTD., Model Ship Display Pedestal Kit CTG-A001410_V0_R0;
Process/Printing Technology: HP Multi Jet Fusion,
Material: PA-12.
![Album image #184 Album image #184](/albums/img/4/7/0/1298470-106039-26-720.jpg)
3D Printed Model Pedestals.
Dimension: D = 60 mm; H = 80 mm.
COBOTEC GROU LTD., Model Ship Display Pedestal Kit CTG-A001410_V0_R0;
Process/Printing Technology: HP Multi Jet Fusion,
Material: PA-12.
Dimension: D = 60 mm; H = 80 mm.
COBOTEC GROU LTD., Model Ship Display Pedestal Kit CTG-A001410_V0_R0;
Process/Printing Technology: HP Multi Jet Fusion,
Material: PA-12.
![Album image #185 Album image #185](/albums/img/4/7/1/1298471-106039-86-720.jpg)
3D Printed Model Pedestals.
Dimension: D = 60 mm; H = 80 mm.
COBOTEC GROU LTD., Model Ship Display Pedestal Kit CTG-A001410_V0_R0;
Process/Printing Technology: HP Multi Jet Fusion,
Material: PA-12.
Dimension: D = 60 mm; H = 80 mm.
COBOTEC GROU LTD., Model Ship Display Pedestal Kit CTG-A001410_V0_R0;
Process/Printing Technology: HP Multi Jet Fusion,
Material: PA-12.
![Album image #186 Album image #186](/albums/img/4/7/2/1298472-106039-40-720.jpg)
3D Printed Model Pedestals.
The Ship's Bow bearer (left) and the stern carrier (right) have different geometry.
Dimension: D = 60 mm; H = 80 mm.
COBOTEC GROU LTD., Model Ship Display Pedestal Kit CTG-A001410_V0_R0;
Process/Printing Technology: HP Multi Jet Fusion,
Material: PA-12.
The Ship's Bow bearer (left) and the stern carrier (right) have different geometry.
Dimension: D = 60 mm; H = 80 mm.
COBOTEC GROU LTD., Model Ship Display Pedestal Kit CTG-A001410_V0_R0;
Process/Printing Technology: HP Multi Jet Fusion,
Material: PA-12.
![Album image #187 Album image #187](/albums/img/4/7/3/1298473-106039-80-720.jpg)
Searching for a suitable alternative basis concept for the model:
Standard Model Pedestal (from Das Werk) versus New 3D Printed Pedestals (HP MJF, PA-12, Self-color).
Standard Model Pedestal (from Das Werk) versus New 3D Printed Pedestals (HP MJF, PA-12, Self-color).
![Album image #188 Album image #188](/albums/img/4/7/4/1298474-106039-64-720.jpg)
Searching for a suitable alternative basis concept for the model:
The Ship is Installed with New 3D Printed Pedestals (HP MJF, PA-12, Self-color).
Standard Model Pedestal (from Das Werk) in Front.
The Ship is Installed with New 3D Printed Pedestals (HP MJF, PA-12, Self-color).
Standard Model Pedestal (from Das Werk) in Front.
![Album image #189 Album image #189](/albums/img/4/7/5/1298475-106039-22-720.jpg)
A suitable alternative Concept for the Model Pedestal:
The Ship is Installed with New 3D Printed Pedestals (HP MJF, PA-12, Self-color).
The Ship is Installed with New 3D Printed Pedestals (HP MJF, PA-12, Self-color).
![Album image #190 Album image #190](/albums/img/4/7/6/1298476-106039-20-720.jpg)
A suitable alternative Concept for the Model Pedestal:
The Ship is Installed with New 3D Printed Pedestals (HP MJF, PA-12, Self-color).
The Ship is Installed with New 3D Printed Pedestals (HP MJF, PA-12, Self-color).
![Album image #191 Album image #191](/albums/img/4/7/7/1298477-106039-48-720.jpg)
A suitable alternative Concept for the Model Pedestal:
The Ship is Installed with New 3D Printed Pedestals.
The Ship is Installed with New 3D Printed Pedestals.
![Album image #192 Album image #192](/albums/img/4/7/8/1298478-106039-25-720.jpg)
A suitable alternative Concept for the Model Pedestal:
The Ship is Installed with New 3D Printed Pedestals.
The Ship is Installed with New 3D Printed Pedestals.
![Album image #193 Album image #193](/albums/img/4/7/9/1298479-106039-76-720.jpg)
U-9 Submarine Model on 3D Printed Pedestals and in Vitrine Base, Oak (Concept).
![Album image #194 Album image #194](/albums/img/4/8/0/1298480-106039-99-720.jpg)
3D Printed Model Pedestals
![Album image #195 Album image #195](/albums/img/4/8/1/1298481-106039-73-720.jpg)
3D Printed Model Pedestal.
![Album image #196 Album image #196](/albums/img/4/8/2/1298482-106039-29-720.jpg)
3D Printed Model Pedestals.
Dimension: D = 60 mm; H = 80 mm.
COBOTEC GROU LTD., Model Ship Display Pedestal Kit CTG-A001410_V0_R0;
Process/Printing Technology: HP Multi Jet Fusion,
Material: PA-12.
Dimension: D = 60 mm; H = 80 mm.
COBOTEC GROU LTD., Model Ship Display Pedestal Kit CTG-A001410_V0_R0;
Process/Printing Technology: HP Multi Jet Fusion,
Material: PA-12.
![Album image #197 Album image #197](/albums/img/4/8/3/1298483-106039-14-720.jpg)
3D Printed Model Pedestals.
Dimension: D = 60 mm; H = 80 mm.
COBOTEC GROU LTD., Model Ship Display Pedestal Kit CTG-A001410_V0_R0;
Process/Printing Technology: HP Multi Jet Fusion,
Material: PA-12.
Dimension: D = 60 mm; H = 80 mm.
COBOTEC GROU LTD., Model Ship Display Pedestal Kit CTG-A001410_V0_R0;
Process/Printing Technology: HP Multi Jet Fusion,
Material: PA-12.
Kommentare
16 23 January 2022, 00:58
![](/profiles/img/72708-240-s.jpg)
when in service it had only 2 front dive planes the middle was removed
14 March 2022, 15:50
Album info
A brief summary of what has been done through the eyes of the camera.
Corrections, additions, etc., which were successfully introduced into the model on the basis of literature and photographs.
Despite the proper model, adjustments and corrections had to be made.
___
I was able to delete the album in the meantime when I tried to change the order of the photos. But now the situation has been restored.
I hope it is helpful for the fellow fighters.
There is a new challenge ahead - to design and model proper carriers for the model on which to present the model.
3D design and modeling, then 3D print from different solutions.
Coming soon, go for a series of ideas that will materialize in the form of 3D files in the oven!