MorningStar Starfighter

1
May 2, 2022
All the printed pieces, plus the pilot figure I'll use. The main hull had to be split into 3 pieces, and each of the wings into 2 so they would fit on my printer
2
May 2, 2022
The 3 pieces of the main hull epoxied together - not the best job but filler will hide a lot!
3
May 2, 2022
Rear hull section glued on and hull primed
4
May 2, 2022
Each engine comes in 2 parts but have openings at either end for lighting. As I won't be lighting it I glued a circle of styrene sheet into each, sprayed the openings black and glued them all together. They've also been primed.
5
May 2, 2022
The cockpit will be very visible and had some openings for lighting (I think) and the details were a bit sparse. I added a screen to the gap at the front and some extra buttons from styrene (in white)
6
May 2, 2022
At the back of the cockpit I also blocked some holes and added some details with punched styrene circles. I also ran some rubber hoses, because why not?
7
May 2, 2022
Started working on the pilot - I wanted him to be holding one of the throttle levers so I pinned the arm to the shoulder with a bit of flexible wire and set him and the arm in place while some thick superglue dries. It will need some putty and resculpting
8
May 3, 2022
A little bit more work on the pilot's arm, trying to make it look a bit more natural. Aves putty has been used to fill gaps
9
May 3, 2022
Wing parts have been glued together, filled, sanded and primed. Some imperfections needed another round of filler
10
May 3, 2022
Finished painting and weathering the cockpit, painted the pilot and glued him in place
11
May 3, 2022
Canopy glued in place
12
June 2, 2022
After a rethink I decided the ship was too big for a 1/72 fighter, but wanted to keep the cockpit interior. I printed a range of scaled down cockpits to see which one would fit the cockpit when hollowed out
13
June 2, 2022
Eventually decided on a new size and cut out the cockpit tub from the old version
14
June 2, 2022
New cockpit hollowed using a Dremel and tub shaped to fit
15
June 2, 2022
Old tub and new cockpit mated together, with some Aves putty used on the interior joins
16
June 2, 2022
New, smaller body compared to the original
17
June 2, 2022
New, smaller engine compared to the original
18
June 2, 2022
125% wing (centre) compared to 176% original wing. I decided the new wings were still too long so I reprinted them just reducing the length by 80% while keeping the width and depth the same (so they would still fit the body recesses). Mush happier with this.
19
June 4, 2022
Wings being glued in place. Rear section has been painted Light Gunmetal
20
June 4, 2022
All main parts together and primed - cockpit not glued in place but canopy on and masked. Engine nozzles have also been painted and masked
21
June 13, 2022
Base coat grey applied and, after many sessions, the first round of masking is done
22
June 13, 2022
Some Maskol applied for chipping before the first round of painting
23
June 13, 2022
First colour sprayed - dark red for sections of the engines and cockpit, and for some striping
24
June 15, 2022
Painting completed on the engines - was using them to see how well the Vallejo red would stand up to masking
25
August 3, 2022
Masking (finally) completed on the red stripes
26
August 3, 2022
Yellow sections on wings sprayed
27
August 4, 2022
All colours on and masks removed. No surprise - some touch-ups were needed!
28
August 10, 2022
29
August 10, 2022
30
August 10, 2022
31
August 10, 2022
32
August 10, 2022
33
August 10, 2022
34
August 10, 2022
35
August 10, 2022

Kommentare

21 2 May 2022, 04:46

Torsten
Again very exciting and unusual, I find the models off the mainstream always particularly beautiful, am curious how it continues 👍

3 May 2022, 07:15

Uwe Kaeding
Thanks Torsten - yes, while X-Wings and Falcons are nice, you get tired of only seeing them and different stuff gets more interesting. Anyway, this ones moving along - the cockpit is done and I'm waiting for the glue to cure on the canopy

3 May 2022, 12:43

Uwe Kaeding
Had a rethink on this build as it was looking much too large to fit into my 1/72 scale SW collection (it was going to be bigger than my MF or shuttle) and the pilot was looking lost in the cockpit. It looked to me like it might fit as a 1/48 ship so I scaled it down by about 66% and am much happier with the size now. The cockpit has been printed a little bigger than the rest (although it still fits the hole on the body) and has been hollowed out to fit the original cockpit tub. I think the pilot doesn't look quite as lost in there now. Even the scaled down wings looked too long to me so I reprinted them with reduced length while keeping the width and depth the same, so they would still fit the slots in the body.

Luckily I could do all this with the 3D printer, and I didn't have to be concerned about real life as its a fictional ship and there aren't any official sizes for it!

2 June 2022, 02:27

Torsten
Very interesting to see the parts in comparison, I watch excitedly further 👍

4 June 2022, 08:55

Christian Lehmann
👍

4 June 2022, 09:02

S M
Interesting topic. Following!

4 June 2022, 09:27

Thomas Espe
👀

6 June 2022, 10:23

Dash Rendar
Pretty interesting, keep it up man!

13 June 2022, 04:53

Uwe Kaeding
Thanks everybody - finally started on getting some colours down, although there will be more masking sessions before each of the next colours

13 June 2022, 06:19

Живко Джаков
Congratulations, he is very good! I'm following.

15 June 2022, 09:40

Spanjaard
looking really good!

15 June 2022, 10:59

Robin (WhiteGlint)
Such a cool project 👀

15 June 2022, 11:30

Uwe Kaeding
Thanks guys - this one is finished now and quite happy with the way it came out. Very weird looking ship!

10 August 2022, 03:35

Torsten
And again an unusual model away from the mainstream, super 😎, very good work with many beautiful details, TOP, ❤️️ it

10 August 2022, 04:40

Robin (WhiteGlint)
Just awesome! Very creative 👍

10 August 2022, 06:26

Uwe Kaeding
Thanks guys - can't take any credit for the weird design though: they made some strange ships for the prequel games and Mark Kozik (Zarkus Models) did a fantastic job on the 3D model. Was very happy with the rework of the cockpit though.

10 August 2022, 12:38

S M
Really cool colors and nice chipping!😎👍

10 August 2022, 14:55

Dash Rendar
Very well done! Looks awesome!

10 August 2022, 16:11

Uwe Kaeding
Thanks guys. S M: the chipping was done with Maskol and a sponge - worked well for the red and blue sections but not quite as well for the yellow, which was harder paint finish. Happy with the way it came out though.

11 August 2022, 05:42

Album info

This is a companion-piece to the Dianoga starfighter, again from the prequel-era Star Wars: Starfighter game, one of the ships flown by a prate faction. The model is 3D printed from a file found on Thingiverse, posted on there by Zarkus Model Kits. The original file is scaled at 1/144 so I scaled it up by 200% to fit my preferred 1/72 scale. I did a test print of the cockpit and 200% turned out to be too big to fit my 1/72 pilot figure. Scaling the file at 176% ended up fitting the pilot nicely, so all pieces were printed at that scale using an Elegoo Mars 2P and Siraya Tech Fast Grey resin

Star Wars: Smuggler, Pirate & Bounty Hunter Ships

193 Bilder

1:72

In Bearbeitung

1:72 Millennium Falcon (Fine Molds SW-6)

19+

Alle Alben

Alle Alben anzeigen »