Pagani Zonda C12S (Job Log)
![Album image #1 Album image #1](/albums/img/5/2/6/1352526-37066-34-720.jpg)
Rivets around the headlamps were removed and holes were drilled for detail-up.
![Album image #2 Album image #2](/albums/img/5/2/7/1352527-37066-14-720.jpg)
Sanded.
![Album image #3 Album image #3](/albums/img/5/2/8/1352528-37066-47-720.jpg)
Washed.
![Album image #4 Album image #4](/albums/img/5/2/9/1352529-37066-96-720.jpg)
The bottom plate is twisted.
Kits that have been stored for a long time and are full of contents are recommended to be checked before assembly. (ex: Revell kits)
Kits that have been stored for a long time and are full of contents are recommended to be checked before assembly. (ex: Revell kits)
![Album image #5 Album image #5](/albums/img/5/3/0/1352530-37066-89-720.jpg)
Painted black surfacer. (Gaianotes)
![Album image #6 Album image #6](/albums/img/5/3/1/1352531-37066-13-720.jpg)
The surfacer in the unsanded areas fell off powerlessly.
![Album image #7 Album image #7](/albums/img/5/3/2/1352532-37066-36-720.jpg)
Just in case, I sanded all the places where the surfacer fell off while attaching and removing the tape on the other parts.
![Album image #8 Album image #8](/albums/img/5/3/3/1352533-37066-46-720.jpg)
This time, the etching parts also need to be painted, so I painted with Vallejo Mecha Primer (black).
![Album image #9 Album image #9](/albums/img/5/3/4/1352534-37066-32-720.jpg)
If the plated wheel is painted black from the inside, the spokes will look thinner and more edge.
![Album image #10 Album image #10](/albums/img/5/5/9/1352559-37066-41-720.jpg)
L: Silver
R: Flat Aluminium
R: Flat Aluminium
![Album image #11 Album image #11](/albums/img/5/6/0/1352560-37066-48-720.jpg)
IPP Super Gold.
![Album image #12 Album image #12](/albums/img/5/6/1/1352561-37066-94-720.jpg)
Mirror-like plated parts. However, due to the gate marks, I sanded it down and then applied Vallejo Gloss Black Primer.
![Album image #13 Album image #13](/albums/img/5/6/2/1352562-37066-52-720.jpg)
And... Painted chrome.
![Album image #14 Album image #14](/albums/img/5/6/3/1352563-37066-14-720.jpg)
The gate marks on the lightly plated parts were sanded and then painted with normal silver.
![Album image #15 Album image #15](/albums/img/5/6/4/1352564-37066-97-720.jpg)
I painted the carbon pattern using stockings.
![Album image #16 Album image #16](/albums/img/5/6/9/1352569-37066-63-720.jpg)
![Album image #17 Album image #17](/albums/img/5/6/8/1352568-37066-96-720.jpg)
I mixed it to paint it a very pale yellowish silver color.
The left, which I first mixed, was more yellow than expected, so I mixed one more with Tamiya's titanium silver as a base.(Arrow)
The left, which I first mixed, was more yellow than expected, so I mixed one more with Tamiya's titanium silver as a base.(Arrow)
![Album image #18 Album image #18](/albums/img/5/7/0/1352570-37066-88-720.jpg)
Done.
![Album image #19 Album image #19](/albums/img/5/7/1/1352571-37066-81-720.jpg)
Clear coated.
![Album image #20 Album image #20](/albums/img/5/7/2/1352572-37066-32-720.jpg)
Clear coated to carbon pattern parts too.
If the carbon pattern is coated with glossy clear, the pattern becomes clearer.
If the carbon pattern is coated with glossy clear, the pattern becomes clearer.
![Album image #21 Album image #21](/albums/img/2/2/6/1353226-37066-61-720.jpg)
Vallejo Mecha Primer(Sand).
You don't have to worry about the color development of the primer because you're going to paint a paint with good shielding power on top of it anyway.
You don't have to worry about the color development of the primer because you're going to paint a paint with good shielding power on top of it anyway.
![Album image #22 Album image #22](/albums/img/2/2/7/1353227-37066-17-720.jpg)
For the red leather color, Gaianots Oxide Surfacer was used.
![Album image #23 Album image #23](/albums/img/2/5/0/1353250-37066-77-720.jpg)
Sanded.
![Album image #24 Album image #24](/albums/img/2/5/1/1353251-37066-39-720.jpg)
Washed.
![Album image #25 Album image #25](/albums/img/2/5/2/1353252-37066-55-720.jpg)
Polished.
![Album image #26 Album image #26](/albums/img/2/5/4/1353254-37066-15-720.jpg)
The compound I used this time.
For finishing, we recommend the ceramic compound on the right.
For finishing, we recommend the ceramic compound on the right.
![Album image #27 Album image #27](/albums/img/2/5/3/1353253-37066-55-720.jpg)
Removed the masking tape.
![Album image #28 Album image #28](/albums/img/6/5/9/1353659-37066-84-720.jpg)
painted with a hand brush. (Vallejo)
![Album image #29 Album image #29](/albums/img/6/5/8/1353658-37066-61-720.jpg)
Applied decal.
![Album image #30 Album image #30](/albums/img/6/6/0/1353660-37066-66-720.jpg)
Ready to assemble.
![Album image #31 Album image #31](/albums/img/1/4/7/1354147-37066-54-720.jpg)
Assembly starts with the engine.
![Album image #32 Album image #32](/albums/img/1/4/8/1354148-37066-68-720.jpg)
Detail-up with PE included in optional parts.
![Album image #33 Album image #33](/albums/img/1/4/9/1354149-37066-13-720.jpg)
Assembled engine.
![Album image #34 Album image #34](/albums/img/1/5/0/1354150-37066-10-720.jpg)
The interior was also assembled and placed on the lower plate along with the engine.
![Album image #35 Album image #35](/albums/img/1/5/1/1354151-37066-43-720.jpg)
Another photo one.
![Album image #36 Album image #36](/albums/img/1/5/2/1354152-37066-28-720.jpg)
Another photo one.
![Album image #37 Album image #37](/albums/img/1/5/3/1354153-37066-24-720.jpg)
The inside of the tail lamp was painted with a chrome marker.
![Album image #38 Album image #38](/albums/img/1/5/4/1354154-37066-16-720.jpg)
Assembled the tail lamp and exhaust.
The tail lamps are all divided by color, so it was very easy to assemble.
The tail lamps are all divided by color, so it was very easy to assemble.
![Album image #39 Album image #39](/albums/img/1/5/5/1354155-37066-20-720.jpg)
The rear parts were also attached to the lower plate, and the wheel axle parts were also attached to the front.
![Album image #40 Album image #40](/albums/img/1/6/8/1354168-37066-92-720.jpg)
Just following to the manual...
![Album image #41 Album image #41](/albums/img/5/8/9/1354589-37066-85-720.jpg)
I roughly restored the thing that I missed and fell into the plate where I put the ROCTITE.
![Album image #42 Album image #42](/albums/img/5/9/0/1354590-37066-13-720.jpg)
The windshield and dashboard were attached to the frame.
The marked part seems to be a fuel tank, but about 60 liters?
Considering the fuel economy of this car, I think 60 liters is small.
The marked part seems to be a fuel tank, but about 60 liters?
Considering the fuel economy of this car, I think 60 liters is small.
![Album image #43 Album image #43](/albums/img/5/9/1/1354591-37066-43-720.jpg)
Cockpit done.
![Album image #44 Album image #44](/albums/img/5/9/3/1354593-37066-84-720.jpg)
It is good to coat the parts attached from the inside of the hood with wood glue so that they do not fall off after assembly.
![Album image #45 Album image #45](/albums/img/5/9/2/1354592-37066-94-720.jpg)
For the rear hood, etching parts must be attached, but since there is no separate guide mold for the attachment location, it must be attached carefully with Loctite.
After attaching it, lightly coat it with wood glue to make it stick more firmly.
After attaching it, lightly coat it with wood glue to make it stick more firmly.
![Album image #46 Album image #46](/albums/img/6/0/7/1354607-37066-97-720.jpg)
Assembled the door.
It's thick and has a lot of detail, so it seems like there are a lot of parts, but it's made up of three pieces.
It's thick and has a lot of detail, so it seems like there are a lot of parts, but it's made up of three pieces.
![Album image #47 Album image #47](/albums/img/6/0/8/1354608-37066-57-720.jpg)
It's a little tricky to assemble because one of the wing's pillars is divided.
The lip spoiler was surprisingly easy to attach.
The lip spoiler was surprisingly easy to attach.
![Album image #48 Album image #48](/albums/img/6/0/9/1354609-37066-52-720.jpg)
A metal sticker included in the optional parts was applied.
![Album image #49 Album image #49](/albums/img/6/1/6/1354616-37066-90-720.jpg)
There are no guides or indications for the location or angle of side mirror attachment, so you have to rely on your senses and attach them with a well-balanced left and right. 😠
![Album image #50 Album image #50](/albums/img/6/1/7/1354617-37066-21-720.jpg)
The front and rear hoods can be assembled with a choice of open or closed.
They designed it so well, I don't understand why they didn't add door hinges.
They designed it so well, I don't understand why they didn't add door hinges.
![Album image #51 Album image #51](/albums/img/6/1/8/1354618-37066-40-720.jpg)
It felt like the producers were passionately designing molds, but eventually gave up due to running out of stamina.
![Album image #52 Album image #52](/albums/img/6/3/9/1354639-37066-91-720.jpg)
I don't like open gimmicks anyway, so I'll cover them all, but I applied glue for temporary fixing to the necessary parts to harden them so that they don't completely fix.
The green glue shown in the back is water-based and retains moisture even after completely hardening, so you can attach and detach the parts.
The green glue shown in the back is water-based and retains moisture even after completely hardening, so you can attach and detach the parts.
![Album image #53 Album image #53](/albums/img/6/4/0/1354640-37066-12-720.jpg)
Finished.
![Album image #54 Album image #54](/albums/img/6/4/1/1354641-37066-58-720.jpg)
Finished.
![Album image #55 Album image #55](/albums/img/6/4/2/1354642-37066-38-720.jpg)
I should have detailed-up the rivets around the headlamps, but I forgot, so I worked on it belatedly. 😉
All done. Thanks for watching~
All done. Thanks for watching~
Kommentare
9 1 December 2022, 14:33
![](/profiles/img/108467-993-s.jpg)
Yes I did buy a few kits on the
second hand market
Idiscovered problems whed things not being straight
And learnt not to heat them up whed a lighter lol
So I may be abel to save some now lol
So a very interesting build to watch
Would appreciate lots of photos and notes on this build
Lots to learn on this subject
1 December 2022, 15:35
![](/profiles/img/37066-788-s.png)
Thanks Jv. This time Just nothing special and I just finished it normally.
Never use a lighter when correcting a twisted part, just soak it in hot water for a few seconds, remove it, twist it slightly in reverse, and cool it in cold water.
1 December 2022, 15:48
![](/profiles/img/108467-993-s.jpg)
Yes I learnt the had way but dident know better
Learnt much here sofare and all have been very helpful
Your builds are always educating and very nice to see
This is a kit I love to have
Many on that list lol
3 December 2022, 06:19
![](/profiles/img/117701-211-s.jpg)
Looks great so far! I have heard some stories that the Aoshima Pagani kits dont fit at all therefore i am curious how yours fits
3 December 2022, 07:20
![](/profiles/img/37066-788-s.png)
@Marco - I know that 'Huayra' doesn't fit well. But while working on the C12, there was no part that didn't fit well. 😉
4 December 2022, 16:43
Album info
FHD Images are here.
Review - motorart.tistory.com/573
JobLog 1/2 - motorart.tistory.com/582
JobLog 2/2 - motorart.tistory.com/585