Noticias
Dmwilde
quiere este artículo
quiere este artículo
Kawanishi H8K2 Type 2 Flying Boat Model 12 '901st Flying Group'
Hasegawa 1:72
02473 2024 Nuevas calcas 16 August, 13:17
Bill C
will attend
will attend
Modelpalooza Saskatchewan 2024
18-20 Octubre 2024
18-20 Octubre 2024
15 August, 20:38
Ken Kolenovsky
Not sure where this listing came in Bill, but it is not the one I put on Scalemates. This one is listed under "Group Builds" and that isn't what I set it up as. I also see that there is a link to our Facebook site, but I didn't enter that. Curious.
Not sure where this listing came in Bill, but it is not the one I put on Scalemates. This one is listed under "Group Builds" and that isn't what I set it up as. I also see that there is a link to our Facebook site, but I didn't enter that. Curious.
16 August, 13:16
Simon Smith
tiene este artículo
tiene este artículo
Panzer Kampf Flugzeug 40
Fledermaus aka. Jagd Flugzeug 40(S) Nitto 1:20
SF3D Series 11 1984 Nuevos moldes 16 August, 13:15
Alex Rakhimgulov
Nuevo álbum de fotos añadido
Nuevo álbum de fotos añadido
36 imágenes
KV-9 for painting practiceNuevo: 16 August, 13:14 1:35
Proyecto: KV-9 for painting practice
23 27 June, 09:04
Villiers de Vos
Very nice texturing and weld marks on this Soviet beast. The photo etch details is a nice touch.
Very nice texturing and weld marks on this Soviet beast. The photo etch details is a nice touch.
10 July, 02:10
Alex Rakhimgulov
Thank you, Mate! This photo etch is selfmade from 0.2mm brass plate ))) I need to buy the photo etch bender, to make it better. ))
Thank you, Mate! This photo etch is selfmade from 0.2mm brass plate ))) I need to buy the photo etch bender, to make it better. ))
10 July, 07:14
Alex Rakhimgulov
Thanks, Mate!
I try to make weld beads like on my favorite YT cannel )))
1) I make a groove with scraiber, if it necessary on the plane surfaces.
2) Next, i prepare 2 component putty, and make a thin "laces" out of it.
3) After that, I carefully fill the grooves and angles with putty "laces" and apply welding texture with special tool (toothpick with tip warped with brass sheet, witch forms small speared C shape).
That is all.
Thanks, Mate!
I try to make weld beads like on my favorite YT cannel )))
1) I make a groove with scraiber, if it necessary on the plane surfaces.
2) Next, i prepare 2 component putty, and make a thin "laces" out of it.
3) After that, I carefully fill the grooves and angles with putty "laces" and apply welding texture with special tool (toothpick with tip warped with brass sheet, witch forms small speared C shape).
That is all.
9 August, 09:30
Landlubber Mike
Nuevo álbum de fotos añadido
Nuevo álbum de fotos añadido
46 imágenes
MyAlbumNuevo: 16 August, 01:32 1:72
This picture is of BuNo 1063 - the subject I will be modeling. Very famous plane - was one of the ten JRS-1s that survi...
Proyecto: Sikorsky JRS-1 (Eduard)
35 2 February, 15:21
Lochsa River
have to sit in...this is in the stash...I was looking at it yesterday...
have to sit in...this is in the stash...I was looking at it yesterday...
25 February, 04:13
Landlubber Mike
Thanks for following guys. Lochsa, you're right about the canopy. There are fit issues in general with this kit - most of which aren't too difficult to deal with - but the canopy is a bit of a mess. I'm not really looking forward to that part of the build.
Thanks for following guys. Lochsa, you're right about the canopy. There are fit issues in general with this kit - most of which aren't too difficult to deal with - but the canopy is a bit of a mess. I'm not really looking forward to that part of the build.
25 February, 17:33
Trude Barkhorn
tiene este artículo
tiene este artículo
JGSDF Type 10 MBT Workable Tracks Contract 1 (w/o Rubber Pad)
Raupen Modell 1:35
35-003 2013 Nuevos moldes 16 August, 13:00
Filip
quiere este artículo
quiere este artículo
"Stuka zu Fuss"
UE-sWG 40/32cm Wk Fl Sfl. für 32cm sWur 40 auf Inf.Schlp. UE 630(f) early Mirage Hobby 1:35
35519 1998 Nuevas piezas 16 August, 12:59
Filip
quiere este artículo
quiere este artículo
UE-sWG 40/28cm Wk Spr Sfl. für 28cm sWur 40 auf Inf.Schlp. UE 630(f) late
Mirage Hobby 1:35
35518 1998 Nuevas piezas 16 August, 12:59
/es/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=es
35
35
/es/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo