Noticias

Villiers de Vos
Nice progress.

Patrick Hagelstein
Ow jeah! I'm in! 👍

Thomas Bischoff
I am in too!

Jos Jansen
Count me in Sid...nice progress!

Spanjaard
very nice progress indeed. very nice looking Phantom

Marius
Looks great, outstanding surface quality!

Maciej Bellos
It's shaping up great!

Nathan Dempsey
Looking very nice. Can't wait for more progress.

Marius
Those decals sinking in the details are perfect! Did you use any decal setting solutions?
While it might seem to be an irrelevant detail, those honeycomb "NO STEP" warnings were indeed red for the Navy. Nice to see a well researched decal sheet. Many other decal sheets are giving these signs in yellow or black.

What products are you using for the gloss and later for thr matt varnis?

Sid de Koning
I use DACO medium and strong on the Furball stencil set. It's not fit to size for Tamiya despite their statement. Also lacking proper instructions and missing some stencils.
After some daco I cut the decals with a sharp blade over panel lines and use a pin to enhance rivets.
Despite being applied on glossy surface there is still a lot of silvering.

Gloss is Future. Matt will be Alclad2.

Marius
I also use Future as gloss, but sometimes it turns permanently milky (without any other repair options) when I'm using strong decal setting solutions.
Have you had a positive experience with thr Alclad Matt varnish?

Sid de Koning
Yes I like the Alclad2 finishes a lot actually. Different grades of matt. I'll be using those as well to further enhance the metal shades.
So far so good I believe. There was a temporary change of color on the left leading edge. Won't a new Future layer help?

Alexander
Looks great already, and no silvering on the pictures as far as I can see 👍
Looking forward to the rest of the build!

Spanjaard
a fantastic Phantom.

Patrick Hagelstein
Phantastic! 👌🏼

Villiers de Vos
Very nice work.

Jos Jansen
Another great "fear-the-bones" artwork...👍🏻!

Thomas Bischoff
A perfect Phantom and well researched. Did you use now the Eduard exhausts? And full marks for the airbrushed markings 👍.
What goodies would you recommend?

Guy Rump
Very nice build! 👍

Sid de Koning
I would definitely advise eduard exhausts, mirrors, hypersonic nose pod and Quickboost fuel dump, Quinta is amazing.
And maybe not as much the Eduard ladder, fin cap (a little too wide on the front) and the seats.
Definitely not the Flying Leathernecks AERO-3B launchers, mine were so badly warped and I couldn't get them straightened out by boiling water. The Furball stencils are better sized for Academy and not entirely correct, misplaced or complete. But it does give that stenciled look. Both speedbrakes and tail hook take some time to get rid off the 3D print Marks.
And the Dead Design masks didn't fit mine.

Thanks for the positive comments!

Nathan Dempsey
A beautiful finish. Much respect for all those stencils!

Michael Kohl
Clean build. Well done.

Neuling
Very clean and careful work. Top result.

Richard Berrie
Phenomenal job! Loves all the photos and the time you took to document your build. Well done!

Oliver Zwiener
Klasse Ding !

Paul Moore
That's a beauty Sid! Congratulations. Do you know what the ordnance load out on this mission (12 Mk.82's) or give it your best estimate? Makes me want to do this version myself.

Sid de Koning
Thanks Paul. I would like to think my model displays may be the best guessed load-out for that mission in the hands of VF-84.

Fazilyek
Hello, Sid.
Amazing job with little tweaks to represent early blocks. I have a question about early blocks stabilizers without strengthening plates(pic 18). So far I haven't seen them mentioned on anything other than super early F-4H and I could not find any good resolution photo with F-4B stabilizer without reinforced plating. On VF-84 F-4B you can definetely see them absent, but I've seen some photos with plating being painted white and basically it resembles a straight line from some distanse. Can you help with finding source materials/photos for early "B" stabilizers and production blocks they were used on, please? I have intention to build some pre-block-26 F-4B too.

Sid de Koning
Send me a PM with your email and I'll send the material I have.

Ian Doody
Ebay gluebomb restoration project. Stripped the built parts down and cleaned them up.The beginnings of paint up. So much more do. But fun bit next, painting metallics by hand, and weathering it.

Ian Doody
Just started to block in the aluminium tub colours, only added a watered down acrylic brown/black wash. Now I wait for it to dry, then ink wash, aluminium layer, then varnish, then another light brown wash.

Kyle DeHart
Off to a quick start. You'll have it looking great in no time.

Ian Doody
First ink wash, just to put some life into the aluminium. I'll dry brush another metallic layer over this, then varnish, the do some more washes. Not a quick process, mainly due to drying times, but it looks really good.

Ian Doody
That's it for today. Still very early stage, second ink wash. It will become more subdued as I continue with layering the aluminium. This is an acceptable beginning though.

Villiers de Vos
Very nice weathering.

Jv
Taking a seat I am interested in how you strip it down I bought a few glue booms myself and not sure how to get the glue of

Ian Doody
That's it for today, and for now on this project. I've lost inspiration and desire to work on it, so back in the box, until I feel inspired to do it again. Just not feeling it, and I don't want to muck it up. Added a varnish layer, fitted the foot pedals and fixed the hole in the tub wheel bay cover.

Ian Doody
Back to the big Ferrari. The cool thing about 70s Tamiya kits, is they gave you buildable tools. It's a screwdriver and wheel nut wrench. Nice.

Ian Doody
Not a lot happening at the moment, I'm doing a lot of sanding, glueing small parts, changing bolt heads on the rear of the gearbox and brakes, as these will be seen. I'll add and swap out bolts on the black crossmember, suspension brace, as its also quite noticable. Also drilled holes in the e haust brackets, for the retention springs, Just a quick dry fit too. Even unpainted the engine is an impressive piece of hand-built model engineering from Tamiya.

Mark D
Following this one! (Have the same one waiting (with a little less glue)

Ian Doody
Scratch built the rear brake air intake cooling scoop bracket. Mad? Me? Probably 😂 there is no line down the middle, it's the crappy silver plastic. It makes dark marks appear at joins and sprue attachment points. I'll putty over the intake, then paint it to look like the clear fibreglass, suitably weathered, with a piece of tape to lesson the amount of air reaching the brakes, just like on the real thing. Exciting things ahead 😉

Ian Doody
And, yes I'm going to put in brake lines.

Villiers de Vos
Very nice progress.

Ian Doody
That's it for today, just blocked in some colour, weathering and extra details tomorrow.

Kyle DeHart
Looking good Ian!

Ian Doody
Weeeell, that's all for today. I'm knackered. Pretty good progress, I've almost finished the 312T's Transverse gearbox, added the plumbing, detail and weathering paint, painted the brake airscoops, added nuts, and painted the suspension crossbeam. Only the anti-roll bar and a bracket still to fit. Bloody good fun that was.

Ian Doody
I think this might turn out rather good.

Ian Doody
As always, doesn't look like I've done anything at all today. Finished off the anti-roll bar and brackets, made a start on the left hand side suspension lower arm, swapped nuts out for better ones, wheel mount, drive shaft and shock absorber, also made a start on the rear wing mounting bracket and battery holder.

bmod
Definitely pulling up a chair to watch this one come along. 🙂 Looks great!

Ian Doody
Not a huge update, as I've had a few days away from modelling. Finished the coil springs on both sides and the right upright and drive shaft. Haven't got to finishing the anti-roll bar yet, as I'm changing the support rods for thinner wire, so it looks more in scale. More soon.

Dominik Weitzer
looks great!

Ian Doody
Back to working on the Tamiya 1/12 1975 Ferrari 312T. Today was just to get reacquainted with the kit, remember where I was, what I had planned, and where I'm going. Tested the fit of the rear wheels and tyres, everything is just friction fitted so far, a long way to go yet. That's how good Tamiya kits are, even forty eight year old kits fit together so well. Work will continue tomorrow with the rear anti-roll bar system, as im making the connecting rods more in scale. This is going to look awesome finished.

Villiers de Vos
Welcome back at the bench Ian.

Ian Doody
As usual not a lot new to see. With one thing or another I've been busy with other things recently. But back to the rear of the 312T. Finished the gearbox, and rear suspension, anti-roll bar adjusters. Replaced the kit parts with pins, for a finer appearance.

Ian Doody
Sloooow work continues on the 312T. The Ferrari Tipo 015, 2,992 cc (182.6 cu in), flat 12, naturally aspirated, engine is a mini kit in itself. Its going to be a complicated, Spaghetti wiring job, there's twelve wires for the fuel injection and twelve wires for the electrical ignition system. Then all the water and assorted pump plumbing. but it's going to look very cool. I am going to add a few things here and there, and I've sourced some air funnel mesh guards. Also I'll be assembling the Octopuss exhaust system of twelve pipes too. Proper Italian plumbing nightmare, but it is a Ferrari lol 😆 all this is just dry fitted for now.

Kyle DeHart
Going to be a stunning powerplant.

Ian Doody
Mixed bag of modelling today, shook sticks at a few different kits. As winter is approaching, looks like I've got Ships and F1 cars in my future. I've been putting the Ferrari off for months as I worked through my Sci-Fi backlog, soo work will commence on the 1975 world championship winning F1 car, my birth year. Doing the bodywork air-intake mod, and scratch building the fibreglass valve covers, plus adding a lot of missing details, wiring and plumbing, swapping nuts n bolts, scratching the accelerator assembly, and spray painting the final bodywork for the first time... a lot to do, but it'll look very cool.

Kyle DeHart
Excellent. It's definitely going to look very cool.

Ian Doody
It has been a whole year since I touched the 1975 Ferrari 312T, omg 😲 finally put paint down on the main case of the Flat 12 engine. More soon.

Ian Doody
Ferrari 312T Tipo 15 Flat 12 engine. Only made a tiny bit of progress today, first pump and hose. More weathering to come. Then fitting all the pipes, electrics, rear transverse gearbox and suspension, and the exhaust system, that all pretty much needs to be done at the same time.

Andrew Horton
Awesome work! I look forward to building my Tamiya phantom!

James C
Fantastic looking pair! 👍
I'm determined to build a Phantom myself before the year is done.

Neuling
Very good looking builds! 👍

Rui S
Looks really Nice 👍

Sebastian Meyner
Great stuff!

Will Dossel
Thx everyone - very much appreciated.

Clifford Keesler
Outstanding pair of Navy birds.

Will Dossel
👍🏻👍🏻

Spanjaard
nice spook! missed it before.

Guy Rump
Very impressive pair 👍

Maciej Bellos
Great result on both aircraft! Well done!

The Brick with wings looks pretty sleek when compared to the Demon, which by no means is a small aircraft.

Alexander
Really good looking result, both of the planes! 👍👍

Rui S
Welcome to scalemates🙂

Rui S
Welcome to scalemates🙂

Rui S
Welcome to scalemates🙂

gorby
Looking forward to seeing this one built. 🙂

Peter G
Welcome to the build! Glad you are following along.

Thomas Bischoff
nice job - I watch the show 👍

David Taylor
Watching.

Christoph Kunz
Amazing build 👍

CaptGPF
Wow! Watching!

Desert Marlin
Same here! This looks really good!

Vincent
Amazing detail and great work on the cockpit. I will be following this build!

J35J
Great progress!👍🏻

David Taylor
Looking good.

Guy Rump
Following. 👍

Rui S
Welcome to scalemates🙂

Rui S
Welcome to scalemates🙂

Rui S
Welcome to scalemates🙂

Rui S
Welcome to scalemates🙂

Rui S
Welcome to scalemates🙂

Rui S
Welcome to scalemates🙂

Martin Oostrom
I spent a couple of hours cleaning up some parts that I cut of the frame

Bozzer
These curbside chassis, really upset me. Just like the Volvo VN. If the manufacturer, went to the trouble, of making an engine, and separate frame parts, with other kits, then why would they cheap out, on kits like these? I love what you're doing with this though. Keep the pictures coming, buddy 👍

Martin Oostrom
I didn't put up pictures of all the cutting and sanding. A summary:
All parts are cut, sanded and glued where possible. Only a few drops of filler were needed.
The cab consists of 10 parts that need to be positioned just right. **** job, but I think I managed.
Next up: Primer.

Martin Oostrom
And primer is on after a monster session. 200ml primer + 50ml SLT = just enough.
Primer is zero paints grey. But a dirty grey.

bughunter
Watching!

Martin Oostrom
Tamiya Bright Red for the chassis and Zero stone grey as main colour for the interior

Martin Oostrom
The Zero stone grey was a bit depressing, so I mixed a batch 50/50 with white to lighten things up a bit.
Tamiya aluminium was airbrushed, and Tamiya black as well.
Done with airbrushing for now. Letting the paint cure before decalling.

Derek Buckmaster
Excellent detailing with the PE! Looking very nice, can't wait for un-masking!