Noticias

Treehugger
I already have so many work-in-progress stuff going on, but I need to finish this smaller project to get to try out making custom railings with wire and styrene, instead of doing that on that other heavy cruiser build from before with the USS Guam. Re. the Guam kit, to try re-work all that photo etch railings was a big mistake, just too much work and probably much harder to align than individual pins togehter with wiring for the deck railing.

The 3d printed turrets w. barrels really look nice, however I also have metal barrels in stock. I will try drilling out just a couple of mm's deeper and see if that works out, if it fails I will have to cut off the resin barrels and add the metal barrels. If I end up using the metal barrels, I must remember to make a "jig" to get the barrel alignment as good as possible without the barrels looking weird "not looking straight".

Hmm, maybe the ship ought to be less angled in the photo there? Not parallel with the "white" edges, but not as angled as this I think. Thinking about this now, I think an "angled" ship is all wrong with the mood of the still water, and I will straighten the model a little to avoid the obvious diagonal angle of the hull there in photo #01.

Not sure if I have larger "isopor" material around, will have to look. I just thought, this might work ok, to draw attention to the model itself, and not end up with a large ocean surface acting as a frame.

A photographer once wrote: "Frame what you love" I think what he meant was, to not add other things into the frame other than the stuff you like/love. A "closer framing" I think is also more "intimate and works better, and also makes the model seem taller as opposed to flat.

Hm, I forgot to think about maaaybe having additional models in the ocean. I do have a tug boat of the same era, I could use that. 🙂

Jörg Schäfer
Interesting, I'll stick with it.

Matti Thomaes
Interesting technique, following with interest. I also used aluminium foil when I made the seascape for my Tashkent, Soviet destroyer, but the way you are doing it is new to me.

Treehugger
Not sure what to expect. A danger here is the foil is so mallable, any accidental denting has to be smoothened out. Should "stabilize" after a few layers of paint and goo hopefully. Hm, if I keep adding goo on top, the goo will flatten and work the opposite way of shaping waves. Might have to just create a glaze close to the foil surface and not fill up with gransparent goo.

Although I have this "isopor" plate ready, I might add black cardboard ontop, as a base for the foil, then add paint on top of that and hopefully some water goo. Probably not a good idea adding too much transparent goo on top of this alu foil as it might look weird perhaps when the foil isn't at the very top of the surface anymore if adding too much transparent goo, unsure.

In computer 3d modeling, there are tools for modeling realistic water waves, but that is too complicated for physical models, unless somehow one starts carving out large waves, then smaller waves and ever smaller waves again, and somehow end up with a nice looking result. Ofc, here there just wouldn't be big waves at all, just smaller waves that slosh around, which is what the steel ball is for.

Steven Van Dyck
Nice project. I once used alufoil too for a 1/700 dio, Operation Torch | Project by StevenVD (1:700) . I found out that if I covered it in Stillwater, I could use water paints on that. But the end result remained quite metallic.

Nicolas
Following

yngvenett
I'm following this to learn

Martin Oostrom
Another tutorial one needs to watch

Gerald Sigmund
@mks: Komakais Walkaround shows meshes for the left and right intakes and none for the center one.

Bozzer
I have no idea of your subject, but I do enjoy your builds. The tutorial is always a lesson, and very informative. Keep them coming 👍

Pepe
Looking

berni
I take a seat 👍

DerMattes
Watching 👍

Johne 69
I am in too 😃

Ben M
When you thin parts, what technique do you use?

MS K
@Ben M - When I need to shave a lot, like this time, I use file.

Michael Kohl
Martin and Bozzer pointed it out. This will be fun and informative to follow.

Matteo Pescarin
Oh wow, as usual, fantastic documentation of the efforts going into this project. Chapeau to you!
Nonetheless, it makes me want to skip any Revell kit from now on... if I only didn't have any in my stash XD

MS K
@Matteo - The new mold products produced since around 2010 are generally nice quality(2CV, VW T1, 911G, Etc...) , but this product is so poorly made that it is ridiculous. I don't know what the production concept of this kit is. It is poor for a precision model, and it's not even easy to assemble.

Michael Kohl
With Revell you better check in advance how that specific kit is rated by others. They have tons of reboxes and quite a few kits where you just wanna ask: are you serious? But then, once in a while, just to show that they are able - in general - to be a serious modelling company, they release some really fine stuff. Doesn't hurt to be prepared what you're up against.

Alexander Grivonev
A true Revell car kit experience 👍 The casted on wiper is especially painful

Michael Kohl
That diffusor is a tremendous improvement.

amazon.com/dp/B00004..aps%2C163&sr=8-3
Such a tool makes such work as fitting the diffusor panels to the chassis much easier (the thinner the needles/pins, the more precise the contour).
Just a german site to give an idea.
Cheers Michael

MS K
Nice idea. I wish there was something made of insect pins thin enough to use in a plamodel.

Johne 69
Great work so far 👍

berni
A question. What Colours you would use at this kit?

MS K
@berni - The red is Italian Red, and I plan to use Cobalt Blue + Sky Blue (the instructions say to mix Ultramarine and Blue).

Denis Dogadov
I make up the silkscreen on the glass with a very thinly sliced masking tape.

[img1]
[img2]

MS K
@Denis - Yeah, I used to do it that way too, before I started using masking film.
My advice is that when masking that way, 'Tamiya masking tape for curves' is much easier than paper tape.
Youtube Video

Spanjaard
wow, your attention to detail and how detail your build logs are, never disappoint! amazing

George Williams
That interior looks really good.

Kesa Tiho
This album is a perfect way to round up why revells models are subpar, why modeling is a great hobby and the lengths humans will go to to achieve perfection. Great progress my guy.

Martin Oostrom
Ah, the big one. Interested!

Kyle DeHart
Look forward to watching this one!

Stéphane Jayet
Promising kit replacing glue by screw in many cases, but there are some moulding issue, so parts have to be well prepared.

George Williams
Good luck with this old kit.

bossy122
I'm cheering for you!

Stéphane Jayet
I just realized that the chassis is totally crooked

George Williams
Any plans to try and straighten it?

Stéphane Jayet
@george, during my vacations for 2 weeks I installed some books on it and it is now almost ok

bossy122
Maybe Arnoux bounced off a Ferrari ; )

Laurent VILLANUEVA HELLER ForEver
super !

Stéphane Jayet
Merci Laurent !

George Williams
Coming along very nicely.

Stéphane Jayet
Thank you George

bossy122
How will you do the black pinstripe? That is what has always kept me from trying this kit.

gorby
Very nice work so far.

George Williams
Great looking engine, the turbo revolution led by Renault.

Stéphane Jayet
Thank you gorby

Stéphane Jayet
@George, I like this engine as well, and I don't remind a kit where the belts are really belt (not plastic formed with the pulleys).

Stéphane Jayet
@bossy122, frankly speaking, I don't know yet. 2 options on the table : option 1 is to cut the decals from the box, option 2 is to do some masking (using tracing paper on the original decals). Option 2 is my preferred option so far.
I already painted the body twice because I had some issues with the masking tape (removing the paint), so hope it will work at first try....

Kyle DeHart
That's really looking excellent!!

bossy122
Can you copy the kits pinstripe then print your own? A little white on one side and a little yellow on the other, covering up any tapes leaks as well.

Stéphane Jayet
Thanks Kyle

Stéphane Jayet
@bpssy122, excellent idea, I will explore this option

Michael Kohl
Looking good

Stéphane Jayet
Thanks Michael

bossy122
Hey! A pinstripe, nice. How did you go about it?

Stéphane Jayet
Hello, I made a kind of combination. Since I was afraid not to get the same yellow colour, I printed the pinstripe on white decal paper, when cutting it I let a small part of the white to have it clean. The difficult part was to have no white on the other side. I had to cut and redo couple of times.
Unfortunately, I realised later that I should have done differently as it was very difficult /impossible to have the large black part parallel to the pinstripe....

Laurent VILLANUEVA HELLER ForEver
tip top !!!

George Williams
Neat work with the pinstripe.

Stéphane Jayet
Thank you Laurent and George

bossy122
Shunko made decals for the Tamiya kit, but of course, they're no where to be found.

Stéphane Jayet
You can also find some decals on indycals.net

bossy122
Are there any cam covers?

Stéphane Jayet
Yes, will be placed later

bossy122
Phew!

Villiers de Vos
Very nice work so far. Your masking and painting is top notch.

Laurent VILLANUEVA HELLER ForEver
great ! my favorit f1