Noticias

Nicolas
Following

Skyhiker
I'm in!

Dave Flitton
Watching!!

Skyhiker
Please let us know when you upload new photos. I don't want to miss anything.

Ogre-Trombone
I found some time to work on these kits, so here are some new photos. Thanks for following!

Nicolas
The instruction isn't mentioning the stand at all. As the torpedo is under the COG I would try to fix it to the torpedo.
Very nice progres so far. 👍

Ogre-Trombone
Leaning that way, Nicolas. I don't like it, but that's probably what I'll need to do.

Mr D
Nice model 👌
Was the Devastator similar to the Dauntless??
Like the subject....will be watching 😃👍

Ogre-Trombone
@Mr D, the Devastator was a pre-War torpedo bomber that was one of the most advanced aircraft of its time. Unfortunately. it was already obsolete at the start of the war. It was slow and underpowered, and early-War tactics left its crews extremely vulnerable.

Skyhiker
The Douglas TBD Devastator, was the U.S. Navy's main torpedo bomber. It was introduced in 1935, but was obsolete by 1939. They were replaced with the Grumman TBF Avenger.

Mr D
Thanks for the info
Ogre & Skyhiker 👍👍
I didn't know much about them, the pre-war yellow wings are smart scheme 👌

Mid Franconian
Great project!

Guy Rump
Looking great, following. 👍

Casey Beckett
Great idea, the foam/tape /white glue - I'm stealing this!

Mr D
Both coming along really nicely now, the flap lines look a lot better now.
Looking like all the build updates.
Good luck with next steps 👌😁👍👍

Ogre-Trombone
Thanks, Mr D. I'm trying not to let the asymmetry bother me on the black-primed model. I wish I'd made a template or measured them instead of trying to follow the old panel lines. Still, I'm glad I made the effort.

Pure improvisation, Casey! It seems to be holding up so far. I want to do open or partially-opened canopies, so it didn't make sense to glue them in place, which is what I usually would have done.

Ogre-Trombone
It's very hot and dry where I am right now, and the paint isn't responding the way I'd like. I'll have to come back when conditions are better.

Mr D
Your doing a 👍 job, All the hard work will pay off, nice project 👍👍

Doubtingmango
So I just finished this little Italian job. The decals came out with a lot of the edges showing, which then got a lot worse when I added some washes. I used Microset on the decals, and then sealed them with Tamiya semi-gloss before the washes, but it actually looks like the washes got under the decals. Any thoughts?

Bogicevic Vladimir
It looks like you haven't spray gloss coat before you applied decals. Or decals didn't set well. There are two solutions. One is lacquer thinner. Put the thinner with fine brush in dots over the place where you have silvering. Thinner should destroy the film. If it raises paint under, just leave it, it will settle back. Important thing here is that, once you applied thinner, you shouldn't touch decal for something like 20 minutes, at least. Second way is mix of sugar and water, half - half. You make a hole with a needle on the decal, than you put mix on the top. It should enter in the space between decal and paint and, when drayed, make a gloss film in between them which will act as a gloss under the decal. Wipe excess mix with wet cloath and you are done.

Mr James
How annoying. I've never heard of the sugar water trick from Bogicevic. I'll be interested if this works. If the thinner, sugar trick fails, what else can you do but use a scalpel to cut around them, since you've sealed it,

Mr James
Oh, nice paintjob by the way

Doubtingmango
Thanks mates! I believe Bogicevic is right. I think I did fail to gloss coat before the decals. I think I'll try the sugar water first

Bogicevic Vladimir
Ok. There are few small tings I should add then. Heat the water first, when hot it will disolve sugar beter and apply it while it's still warm, it will have more viscosity. Make small hole or slice with modeling knife, put few drops of mix on the top and let it dry. You will see emidiatly if it's penatrating. When dry, wipe carefully excess mix with moist cloth. Repeat where neaded. I know it sounds ridiculous, but it worked for me many times.

Doubtingmango
Thanks Bogicevic! I'll give it a shot. If it doesn't work I'll try the lacquer thinner technique. I love this site!

Mark Sherwood
Where the *uck's this been hiding. Very nice build Mr Mango and I hope the decal solution from Bogicevic work's out🤞

Doubtingmango
Thanks Mark! So I punched some holes in the decals and applied the warm sugar water, but unfortunately it did not seem to make a noticeable difference. I decided my best shot was to just grab the scalpel and remove the decals, which was very easy. Bogicevic said the solution would get under the decals! I have successfully applied new decals, and my little Italian job is now base-worthy. New pics to come.

Bogicevic Vladimir
Well, you find a solution, which is the most important thing. I can not know why something that worked for me many times does not work for you in this case. Maybe that what I think is silvering is residual glue from decal paper. Who knows... Anyway, good luck with your project.

Doubtingmango
Thanks Bogicevic! You were definitely part of the solution

John
All's well that ends well. 👍 Mango, your builds have me hankering to do some armor but I still have commitments to do a couple more a/c. When I do get a chance, part of me wants to start small with a Pz IV, but another part says go for broke and do a Maus!

gorby
Very nice work!

Neuling
Good result anyway!

Doubtingmango
Thanks guys!

Doubtingmango
As promised, new pics of the new decals have been added, along with pics of the work I have started on the base. Once again, thank you for the help Bogicevic!

John
Really cool base! 👍

Guy Rump
Great result on the tank, the base looks good too. 👍

Doubtingmango
Thanks John and Guy!

Doubtingmango
More work on the base. Just need to paint up the base and add foliage

Doubtingmango
And it's finished

Rui S
Great work allround 👍 Beautiful vignette

Doubtingmango
Thanks Rui! Always appreciate the feedback

Tcamp
Awesome work

Pietro De Angelis
Beautiful work, congrats!

M0rce
That's pretty cool 😎

Bobby Thumbs
hey man that palm tree is badass excellent work

Doubtingmango
Thank you all! The palm tree is badass, but I can only take credit for the placement. I got it off an Ebay seller from Thailand, Thannan Diorama Exporters. Not cheap, but I had to get one to see if they were as good as they look. They are! Also need to give a shout out to Value Gear for much of the stowage.

Landlubber Mike
Wow, this is fantastic!! The model and the base looks amazing, but that palm tree really pulls it all together in an extra special way. Well done!

Doubtingmango
Thanks Mike!

Spanjaard
great you resolved the decals issue, fantastic dio

Doubtingmango
Thanks Spanjaard! It was a nice save

Bobby Thumbs
aww man I thought you was a next level tree maker - i was gonna hit you up for hints