Noticias

gorby
I think you win this weeks prize for most heavy duty modelling tool. 😄
Looks a very interesting conversion.

Lenny Li
I think that kind of set up can tool a real bogie!!

Neuling
Watching .....................

Jakko ‌
> I think you win this weeks prize for most heavy duty modelling tool. 😄

Probably, yeah 🙂 It's a metalworking lathe, so a bit overkill for just turning down the seam on those wheels, but I didn't feel like aching fingers from scraping them down with a knife — I get those even when I hold them in a modelling vice, never mind just between my fingers.

> that kind of set up can tool a real bogie!!

Having seen a disassembled Sherman bogie up close, I must say I think this one is a size too small for that 😉

Ben M
👀 fascinating vehicle.

Mr D
Looking good, weld's coming on nice 👍

Ben M
How did you hold the wheels in the lathe?

Jakko ‌
@Mr D: that's not the welds yet, it's just the filler needed to plug the gaps 🙁 I'm still debating how to add all the weld seams.

@Ben M: An M2 screw, about 2 cm long, through the hole in the wheel, with a nut to tighten it. It needs to be fairly tight else chances are the wheel will stop as soon as the chisel hits it. On Asuka two-piece wheels, you need to do this before assembling the parts, because the hole on the piece to be glued in is smaller than on the part that has the tyre moulded on it.

Ben M
Thank you, I can envision the setup. I have a small lathe and arthritis in my hands, this technique could help me a lot. Thanks!

Mr D
Regarding weld's l have seen super glue used through a fine tip, you need steady hand n move in pattern to create weld.
Sorry l was looking at the resin 🤔🤣.
Good stuff be keeping eye
On progress 👍👍

Jakko ‌
@Ben M: What also works is a modeller's vice. Clamp the wheel in that, scrape down the seam with a straight knife over a third or so of the wheel, then unclamp and turn it, and repeat. If I scrape more than about two or three wheels by hand, my fingers ache enough that I have to stop, so the vice helps a lot. But you also get a lot of plastic scrapings all over your modelling area, so this time, I figured I'd put those in someone else's hobby room instead for a change 😉

@Mr D: Hahaha! The ones on the resin were put there by Resicast 🙂 But I'll now have to make ones that look similar, or at least not out of place next to them. I'm thinking a thin string of two-part epoxy, textured with a sharp tool.

gorby
I've just seen an Uncle Nightshift vid on adding weld seams:
Youtube Video

Jakko ‌
Thanks for that.

Mr D
Good video 👍, the finish on the flat plate work looks authentic, l think it's had better rough cast look from the brush stippling before he added the putty coat.
Good idea on the weld , epoxy putty best as regular epoxy levels out again.

Jakko ‌
I've begun to add the weld seams now — see photo 23 🙂 Basically, Magic Sculp two-part epoxy putty that I mixed up a very small amount of, then took even smaller amounts from that and rolled it as thin as I could in my hand before pressing it into the join between the parts. Getting it to stick there is tricky, especially once I began texturing it with the tip of a knife — it wants to adhere to skin and steel much better than to plastic, unfortunately 🙁 But with a bit of perseverance it does eventually stick.

Pietro De Angelis
Fantastic work, congrats!

David Taylor
really coming along.

Jakko ‌
Thanks 🙂

Robert Podkoński
I see some heavy duty equipment here and a lot of elbow grease... Good job so far, Jakko! Keep it up!

Jakko ‌
Thanks, though this is fairly straightforward. The most difficult part was finding a good way to curve the splash plates, really.

Pepe
Looking

gorby
You're doing some excellent work on this.

Jakko ‌
Thanks 🙂

Guy Rump
Looking great, following. 👍

Jakko ‌
Cool, nice to have you along 🙂

Mr D
Taking shape now, the green welding joints are looking a better medium.
Interesting to see an adaptation taking place of the original.
Thanks for your posts, good to see steps
👍👍👍

Jakko ‌
Thanks. TBH, I don't really care to look at photos of finished models — I much prefer seeing how they got to be that way, after which the finished pics make sense 🙂 So I post in-progress photos instead of only what it looks like at the end.

Kesa Tiho
Wheel (s)

Mid Franconian
Do you plan any sanctions against your feline roommate?

DuperScale
Oh no, once my kid destroyed my Hasegawa F-16… 😅 Perfect to make a new one.

Eric Thornton
Fluffy Boy only gets treats... models and kitties don't mix. 😅

Lost_Erik
Oh No!

Sean
Nooooooooooooooo!

Kesa Tiho
Well now the F-15 dosent hold a clean record anymore of not being shot down.. did the pilot manage to eject at least? And if so can you fly him to me, i have some ground crew and F-14A buddies he could be friends with

Martin Oostrom
I'd like to be your codriver on this journey

István Szücs
I'm just looking.

Michael Kohl
Looking good.

Ricard Gomicia Calatayud
great job! I don't know if I'd be abme to dirt it after finishing it hahaha

CasModeler
@Ricard
Of course you can do wash after finishing. Just use enamel/acrylics paints and pigment(pulver).

CasModeler
Finished

bossy122
SO dirty!

Martin Oostrom
I can't look in your wallet, but shipping from Poland to Estonia is around €10.
If your age is an issue, be nice to some adults around you 😉

Kesa Tiho
I mean i can give you a rundown on whats in my wallet
My ID
My library card
My debit card
My biking licence
One 20 euro bill
One 10 euro bill
Two 2 euro coins
And a picture of a baby duck

Kesa Tiho
And as for being nice to adults around me i am. Im being a good boi :3

Nicolas
I got mine 3 weeks ago. Following with great interest. Looks good so far. 👍

Roland Sachsenhofer
In view of the start of this build, I was tempted by the following motto: "From ugly duckling to swan": the kit offers a number of interesting challenges, but gives an idea of the potential both as a model and as a representation of a true aircraft beauty! I will try my best to make the swan appear....
A first challenge: roughly moulded parts, poor fit and a wing that wants too much in a positive V-position.... A second challenge will follow in the form of a Vacu canopy that has turned yellow with age; this will give me the opportunity to try out the doing in Vac-canopy myself. More of that next time...

Robert Podkoński
Taking a seat here, too 🙂

Roland Sachsenhofer
It's a pleasure!

Transall NG
Nice aircraft !
One was used in the last phase of the New Guinea gold rush in the 30's...
Good luck !
@+

Cuajete
Great, Roland!
I would like to see the steps you follow when making the Vac-canopy.

J35J
Very intresting project! Taking a seat.

Alex K
In...

Roland Sachsenhofer
Thank you for your interest, I appreciate it!
Cuajete, I'd be happy to show you a few photos of the progress of the construction and application of the self-moulded Vac canopy. It seems to have produced a reasonable result so far....

Erik Leijdens
An unusual subject Roland! No doubt you will end up with a fantastic result

Roland Sachsenhofer
Thank you for your trust and encouragement, Erik!

Cuajete
Many thanks, Roland!
Great job with the putty party and vacuum canopy 👍

What thermoformer did you use?

Thomas Kolb
This look like an intriguing project, but she's definitely a putty queen! I am super impressed with the vac-forming!

Łukasz Gliński
Can't miss that swan

Roland Sachsenhofer
Thank you very much for the answers, mates! I'll show you a few new pictures from today: the surfaces have been reworked with 2000 grit sandpaper (even if it may not look like it, dusty as the "duckling" still is) to prepare it for a first coat of paint. This will certainly show the need for correction! 🙂

Nicolas
I'll grap a seat. Nice work so far.