McDonnell Douglas F/A-18C Hornet (Hasegawa)
![Album image #1 Album image #1](/albums/img/2/3/5/984235-10105-56-720.jpg)
The venerable old Hasegawa Hornet kit which I'll use for this project.
![Album image #2 Album image #2](/albums/img/2/3/8/984238-10105-39-720.jpg)
Plastic still looks pretty good. The sprue on the upper right contains the F/A-18C specific parts.
![Album image #3 Album image #3](/albums/img/2/3/9/984239-10105-15-720.jpg)
Not crazy how the fuselage bits are broken down, but it's common.
![Album image #4 Album image #4](/albums/img/2/4/0/984240-10105-78-720.jpg)
Nice decal sheet from Cartograf (which I won't be using).
![Album image #5 Album image #5](/albums/img/2/3/7/984237-10105-70-720.jpg)
This sheet from TwoBobs has the US Naval Aviation Centennial scheme that I'll be doing (the three colour scheme at bottom).
![Album image #6 Album image #6](/albums/img/2/6/5/984265-10105-15-720.jpg)
VFA-122 painted one of their Hornets in this retro scheme for the US Naval Aviation Centennial.
![Album image #7 Album image #7](/albums/img/2/3/6/984236-10105-15-720.jpg)
I'll be using a bunch of aftermarket goodies.
![Album image #8 Album image #8](/albums/img/2/4/1/984241-10105-53-720.jpg)
The intake trunks are nowhere near deep enough, but they should be much better than what's in the kit.
![Album image #9 Album image #9](/albums/img/2/4/2/984242-10105-95-720.jpg)
Crazy detail in the Aires resin for the wheel wells. I see some grinding and sanding in my future.
![Album image #10 Album image #10](/albums/img/2/4/3/984243-10105-69-720.jpg)
And a new cockpit with far more detail than the kit.
![Album image #11 Album image #11](/albums/img/2/4/4/984244-10105-50-720.jpg)
Not sure if I'll need these stiffeners or not.
![Album image #12 Album image #12](/albums/img/2/5/2/984252-10105-92-720.jpg)
All the shaded areas of the resin castings MUST be removed.
![Album image #13 Album image #13](/albums/img/2/5/3/984253-10105-19-720.jpg)
Otherwise the parts won't fit. Trust me on this one. 🙂
![Album image #14 Album image #14](/albums/img/2/4/5/984245-10105-48-720.jpg)
Compared to F/A-18A kit on left, you can see how much plastic must be removed to make way for the resin.
![Album image #15 Album image #15](/albums/img/2/4/6/984246-10105-41-720.jpg)
I got a little too close when sawing off the casting block - but we're still OK.
![Album image #16 Album image #16](/albums/img/2/4/8/984248-10105-35-720.jpg)
I'll use styrene card stock to cover up the holes.
![Album image #17 Album image #17](/albums/img/2/5/4/984254-10105-46-720.jpg)
Like so. The styrene sheet is 0.127mm (0.005") thick.
![Album image #18 Album image #18](/albums/img/2/4/7/984247-10105-32-720.jpg)
The instrument panel coaming had to be removed as well.
![Album image #19 Album image #19](/albums/img/2/4/9/984249-10105-19-720.jpg)
The sides of the resin cockpit and the sidewalls of the fuselage both needed to be sanded to allow a fit.
![Album image #20 Album image #20](/albums/img/2/5/0/984250-10105-93-720.jpg)
The resin instrument panel and coaming are a drop-in fit. Much nicer than the kit parts.
![Album image #21 Album image #21](/albums/img/2/5/1/984251-10105-23-720.jpg)
Looks like a wee bit of filler needed for the cockpit rails and to blend in the coaming.
![Album image #22 Album image #22](/albums/img/2/5/5/984255-10105-46-720.jpg)
A quick test to make sure everything fits OK. It is a tight fit, the cockpit is right on top of the wheel well.
![Album image #23 Album image #23](/albums/img/2/5/7/984257-10105-82-720.jpg)
For the main gear wheel well some more styrene butchery is required!
![Album image #24 Album image #24](/albums/img/2/5/6/984256-10105-38-720.jpg)
Not just the fuselage - all those ribs on the sidewall need to go. This is not mentioned in the Aires instruction sheet.
![Album image #25 Album image #25](/albums/img/2/5/8/984258-10105-69-720.jpg)
This shows how much grinding to do. Ugh.
![Album image #26 Album image #26](/albums/img/2/5/9/984259-10105-42-720.jpg)
I also had to reshape the resin wheel well to make it match the contours of the lower fuselage.
![Album image #27 Album image #27](/albums/img/2/6/0/984260-10105-80-720.jpg)
But you have to admit the amount of detail is amazing.
![Album image #28 Album image #28](/albums/img/2/7/3/984273-10105-23-720.jpg)
Note how the trailing arm of the main landing gear is nearly parallel to the ground. Hasegawa have this wrong in my opinion.
![Album image #29 Album image #29](/albums/img/2/8/0/984280-10105-16-720.jpg)
The Aires resin seems to have fixed that. Aires in front, Hasegawa in rear. Big difference.
![Album image #30 Album image #30](/albums/img/2/8/1/984281-10105-84-720.jpg)
I added a triangular bit of card stock where the Sparrow missile fin will go. Note how much I had to thin the fuselage for the intakes to fit.
![Album image #31 Album image #31](/albums/img/2/8/2/984282-10105-82-720.jpg)
A lot of sanding required for the intakes as seen here.
![Album image #32 Album image #32](/albums/img/2/8/3/984283-10105-40-720.jpg)
I've read online that the intake and wheel well interfere, but there seems to be enough room.
![Album image #33 Album image #33](/albums/img/2/8/4/984284-10105-59-720.jpg)
The engine faces with some Mr. Color Super Metallic 2 Super Fine Silver and a bit of a wash.
![Album image #34 Album image #34](/albums/img/2/8/6/984286-10105-56-720.jpg)
The other wheel well in place.
![Album image #35 Album image #35](/albums/img/2/8/7/984287-10105-40-720.jpg)
I added a spreader to help reinforce the sidewalls. I think this is a weak area of the kit.
![Album image #36 Album image #36](/albums/img/2/8/5/984285-10105-58-720.jpg)
I sprayed a little Mr. Hobby Flat White to get a better idea of the extra detail the resin provides.
![Album image #37 Album image #37](/albums/img/2/8/8/984288-10105-81-720.jpg)
Who ever made the casting master is a genius. For the detail, not so much for the fit. 🙂
![Album image #38 Album image #38](/albums/img/2/8/9/984289-10105-61-720.jpg)
A wash will really make this detail pop!
![Album image #39 Album image #39](/albums/img/2/9/0/984290-10105-46-720.jpg)
I don't know how accurate all this is, but it looks quite close to photographs. Fine detail painting in my future!
![Album image #40 Album image #40](/albums/img/2/9/1/984291-10105-14-720.jpg)
The inside of the intake trunks were also painted white, and the engine face added.
![Album image #41 Album image #41](/albums/img/2/9/2/984292-10105-26-720.jpg)
This looks so much better than the kit.
![Album image #42 Album image #42](/albums/img/2/9/3/984293-10105-65-720.jpg)
Once all the sanding and grinding was done, the intakes fit nicely.
![Album image #43 Album image #43](/albums/img/2/9/4/984294-10105-82-720.jpg)
I cut the Hasegawa instrument panel decal into 16 separate pieces, and applied them to the Aires resin. I like it!
![Album image #44 Album image #44](/albums/img/6/9/6/984696-10105-90-720.jpg)
Finishing up the cockpit - resin throttle will be added later.
![Album image #45 Album image #45](/albums/img/6/9/7/984697-10105-54-720.jpg)
The ejection handle came from a leftover Eduard PE fret. Hornet cockpits are kind of boring.
![Album image #46 Album image #46](/albums/img/6/9/8/984698-10105-62-720.jpg)
The Hasegawa cockpit decals were dismembered and applied over the resin consoles.
![Album image #47 Album image #47](/albums/img/6/9/5/984695-10105-22-720.jpg)
Everything posed with my weekly allowance for scale. Note the PE rudder pedals.
![Album image #48 Album image #48](/albums/img/8/2/1/987821-10105-68-720.jpg)
Filling the four sink holes present on every 1:72 Hasegawa Hornet.
![Album image #49 Album image #49](/albums/img/8/2/3/987823-10105-53-720.jpg)
I added a lip to help hold the aft end of the deck behind the cockpit. The resin deck is much nicer than the kit's.
![Album image #50 Album image #50](/albums/img/8/2/2/987822-10105-75-720.jpg)
I used the deck to help position the cockpit longitudinally.
![Album image #51 Album image #51](/albums/img/8/2/4/987824-10105-89-720.jpg)
The deck drops right in. I'll leave this off until later in the build to help when masking off the cockpit.
![Album image #52 Album image #52](/albums/img/8/2/5/987825-10105-45-720.jpg)
The instrument panel and rudder pedal assembly drops right in too. This will be attached prior to the windscreen as I'll need to add the HUD.
![Album image #53 Album image #53](/albums/img/8/2/6/987826-10105-93-720.jpg)
Two more sink holes. That's six sink holes on the LEX. Should we call it hex LEX? 🙂
![Album image #54 Album image #54](/albums/img/8/2/7/987827-10105-37-720.jpg)
I added an additional spreader near the intakes. The sidewalls are much more solid now.
![Album image #55 Album image #55](/albums/img/8/2/8/987828-10105-68-720.jpg)
And some filler to blend in the resin intake lips.
![Album image #56 Album image #56](/albums/img/4/7/6/988476-10105-78-720.jpg)
I used a razor saw to cut off the stabilizers. The stumps were then removed with a Dremel.
![Album image #57 Album image #57](/albums/img/4/7/7/988477-10105-48-720.jpg)
Note that the innermost edge of the stabilizers must remain - it's part of the fuselage sidewall.
![Album image #58 Album image #58](/albums/img/7/9/1/994791-10105-46-720.jpg)
The resin retraction arm looks more like the real thing than the kit part.
![Album image #59 Album image #59](/albums/img/7/9/3/994793-10105-46-720.jpg)
I think I ha a short shot with the nose gear. Sheet styrene to the rescue.
![Album image #60 Album image #60](/albums/img/7/9/2/994792-10105-88-720.jpg)
The retraction arm needed to be shortened by 2mm to use the resin wheel well. After cutting, I pinned it to maintain strength.
![Album image #61 Album image #61](/albums/img/7/9/4/994794-10105-93-720.jpg)
Main gear on - I believe I have the splay angle correct. Note the braces added to the intake splitter plates.
![Album image #62 Album image #62](/albums/img/7/9/6/994796-10105-71-720.jpg)
No pylons or armament for this show bird. I filled the holes with styrene rod and putty.
![Album image #63 Album image #63](/albums/img/7/9/7/994797-10105-50-720.jpg)
Still working on the seams, but the fuselage is together.
![Album image #64 Album image #64](/albums/img/7/9/5/994795-10105-56-720.jpg)
Northrop designed a really sleek and sexy airframe. McDonnell and Northrop built it - don't get me started calling it Boeing.
![Album image #65 Album image #65](/albums/img/7/9/8/994798-10105-60-720.jpg)
The RES/KIT wheels are beautiful - very close to the actual size and have radial tread. The kit nose wheels are oversize.
![Album image #66 Album image #66](/albums/img/7/9/9/994799-10105-52-720.jpg)
The resin tailplanes from Quickboost. Even if I don't break it off, the tiny pivot arm won't be strong enough.
![Album image #67 Album image #67](/albums/img/8/0/1/994801-10105-94-720.jpg)
So I pinned them. This is 0.018 in. rigid wire - you can't go any larger due to the thickness of the tailplane.
![Album image #68 Album image #68](/albums/img/8/0/0/994800-10105-98-720.jpg)
And a tiny hole to match. The drill is 0.022 in. - need to leave room for the glue!
![Album image #69 Album image #69](/albums/img/7/0/7/995707-10105-74-pristine.jpg)
The HUD has two combining glass elements. The CMK photoetch provide the brackets.
![Album image #70 Album image #70](/albums/img/7/0/8/995708-10105-19-720.jpg)
Almost looks like the real thing. Very fiddly to put together though, especially in 1:72 scale.
![Album image #71 Album image #71](/albums/img/2/5/6/1005256-10105-87-720.jpg)
Sea Blue 15042 and Intermediate Blue 35164 - you don't see too many Hornets like this.
![Album image #72 Album image #72](/albums/img/2/5/7/1005257-10105-60-720.jpg)
The actual aircraft had a flat finish, so I expect the blues will lighten up a bit with a flat varnish.
![Album image #73 Album image #73](/albums/img/2/5/9/1005259-10105-26-720.jpg)
The first decals are on - no problem here.
![Album image #74 Album image #74](/albums/img/2/6/0/1005260-10105-10-720.jpg)
The port intake warning triangle - note that the letters are "clear."
![Album image #75 Album image #75](/albums/img/2/6/1/1005261-10105-42-720.jpg)
On the port side, the letters are white. Big mistake by TwoBobs, as the letters should be white on both sides.
![Album image #76 Album image #76](/albums/img/2/5/8/1005258-10105-84-720.jpg)
The decals are designed for the Academy kit, and there is a huge difference between that and Hasegawa. Look how much I have to trim.
![Album image #77 Album image #77](/albums/img/2/6/2/1005262-10105-31-720.jpg)
After trimming, everything looks OK to me. TwoBobs give you a bunch of black stencils, but no instructions on where to put them. Photos don't show any stencils like that.
![Album image #78 Album image #78](/albums/img/8/0/9/1008809-10105-40-720.jpg)
I had to shorten the exhaust tubes to fit, but I think they'll be OK.
![Album image #79 Album image #79](/albums/img/8/0/8/1008808-10105-50-720.jpg)
Nobody can tell they're not deep enough!
![Album image #80 Album image #80](/albums/img/8/1/1/1008811-10105-50-720.jpg)
Electrical greeblies added behind the cockpit.
![Album image #81 Album image #81](/albums/img/8/2/4/1008824-10105-50-720.jpg)
A light wash in the gear wells helps bring out the detail.
![Album image #82 Album image #82](/albums/img/8/1/3/1008813-10105-68-720.jpg)
The gear bays were freshly painted on the actual aircraft since it was for the big celebration.
![Album image #83 Album image #83](/albums/img/8/1/4/1008814-10105-34-720.jpg)
Elevators added and posed. Hasegawa forgot the pitot tubes, so I add some from True Details.
![Album image #84 Album image #84](/albums/img/8/1/2/1008812-10105-81-720.jpg)
Big difference between the resin canopy actuator (above) and the kit part.
![Album image #85 Album image #85](/albums/img/8/1/6/1008816-10105-66-720.jpg)
I ran out of parts so she must be done! Enjoy the rest of the photos! 🙂
![Album image #86 Album image #86](/albums/img/8/1/5/1008815-10105-87-720.jpg)
![Album image #87 Album image #87](/albums/img/8/1/7/1008817-10105-53-720.jpg)
![Album image #88 Album image #88](/albums/img/8/1/9/1008819-10105-61-720.jpg)
![Album image #89 Album image #89](/albums/img/8/1/8/1008818-10105-96-720.jpg)
![Album image #90 Album image #90](/albums/img/8/2/0/1008820-10105-46-720.jpg)
![Album image #91 Album image #91](/albums/img/8/2/1/1008821-10105-20-720.jpg)
![Album image #92 Album image #92](/albums/img/8/2/2/1008822-10105-88-720.jpg)
![Album image #93 Album image #93](/albums/img/8/2/3/1008823-10105-87-720.jpg)
![Album image #94 Album image #94](/albums/img/8/2/9/1008829-10105-69-720.jpg)
Much better view than looking into the kit intakes.
![Album image #95 Album image #95](/albums/img/8/2/5/1008825-10105-92-720.jpg)
![Album image #96 Album image #96](/albums/img/8/2/6/1008826-10105-12-720.jpg)
![Album image #97 Album image #97](/albums/img/8/2/7/1008827-10105-95-720.jpg)
![Album image #98 Album image #98](/albums/img/8/2/8/1008828-10105-30-720.jpg)
![Album image #99 Album image #99](/albums/img/3/5/3/1009353-10105-84-720.jpg)
Here she is posed with a tiger-striped Canadian CF-188 that I built about ten years ago.
Comentarios
34 22 April 2021, 12:09
![](/profiles/img/10105-s.jpg)
For my next project I'll be building the Hasegawa 1:72 F/A-18C Hornet in the special US Naval Aviation Centennial markings applied by VFA-122 "Flying Eagles" at NAS Lemoore in 2011. I'm also using the Aires resin sets for the wheel wells and cockpit as well as the Quickboost seamless intakes. As you can see in the photos, there was a lot of grinding and sanding needed to make the resin fit - much more than I typically have to do with Aires resin. The time spent was worth it, though, as the extra detail is just superb. Have a look at my progress so far - all comments are appreciated. Cheers, Bill
22 April 2021, 13:24
![](/profiles/img/21096-573-s.jpg)
aires detail as wonderful as usual. and crazy sanding also as usual. but it is looking great. i love what you have done with instrument panel decals on the aires panel.
22 April 2021, 13:28
![](/profiles/img/10105-s.jpg)
Thanks! Yeah, it seems there is always a lot of sanding with Aires. I sometimes wonder if they ever try using their own products - but then again I completely understand why so much modification is required to the kit.
22 April 2021, 13:49
![](/profiles/img/25429-812-s.png)
What I think it is with Aires is that their measurements are actually the correct ones. They measure their products 1:1, but in real life aircraft skins and dividing panels are a mere couple of mm thick while kit fuselages are also a couple of mm thick, but in 1/72 or 1/48. Sometimes one has to sand the Aires and/or kit walls back to being translucent, that would actually be those couple mm thick aluminum sheets in real life. That's just how accurate they are. 😉
22 April 2021, 13:56
![](/profiles/img/25429-812-s.png)
Bill, why did you go for the Hasegawa kit and not for the newer Academy one? I basically switched out all my Hasegawa Hornets in my stash with Academy ones because of their ease of building and very fine surface details.
22 April 2021, 14:02
![](/profiles/img/21096-573-s.jpg)
are those Academy kits that good Patrick?... my only F-18 in stash is a Hasegawa.... 🙁
22 April 2021, 14:12
![](/profiles/img/10105-s.jpg)
I've never seen the Academy kit other than photos so I can't really compare. I've had the Hasegawa F/A-18A Blue Angels kit in my stash since it came out, and the F/A-18C kit I'm using for this project was a gift. What is the saying - "run what you brung?" 🙂
I've ordered resin wheels and elevators (stabilitors/horizontal tailplanes - whatever they're called). I thought about dropping the flaps but I think I've already done enough cutting, grinding and sanding! Besides, I have several photos that show aircraft parked with the flaps neutral - I assume they're locked somehow in that position.
22 April 2021, 14:50
![](/profiles/img/12294-874-s.jpg)
The instrument panel is a real eye catcher. Sadly those details are hard to see in 1:72 scale.
22 April 2021, 15:11
![](/profiles/img/10105-s.jpg)
True that is, Ingmar. The details will be difficult to see when the fuselage is closed up. But at least I will have the canopy open. I wonder how many hours I've spent adding details that no one will ever see? Ha, too many! Even the resin wheel wells on this Hornet won't be easily seen. That's modelling!
22 April 2021, 17:01
![](/profiles/img/25429-812-s.png)
Oh yes, those Academy kits are good! 👍 My only let down is the inserts on the LEX undersides. Somehow I never manage to install those flush and without noticeable seams. Well, the upside is that's it's the underside. 😉
22 April 2021, 18:50
![](/profiles/img/10105-s.jpg)
@Es-haq, you are right! I will always know they are there (and how much work it took to put them there).
@Patrick, I had a good look at photos of the Academy kit, and it looks very nice. Someday I will get one, but I have to build this one and the Blue Angel bird first. Come to think of it, I already have a Canadian CF-188 Hornet in my display case - I'll end up with Hornets everywhere.
britmodeller.com/for..uglas-cf-188-hornet/
Those tiger stripes are all individual decals. I question my sanity sometimes. LOL
22 April 2021, 19:31
![](/profiles/img/10105-s.jpg)
Thanks, @Spanjaard. That was built quite some time ago. I like tiger schemes, and I have an F-16 project coming up with a Belgian tiger scheme. Should be fun.
22 April 2021, 20:39
![](/profiles/img/25429-812-s.png)
That Canadian Tiger does look (p)aw(e)some indeed! I feel we have a connection here Bill as I 'bumped' into you on Britmodeler while looking for some SHAR information and saw your request for 1/72 information. Also, I'm preparing to build the 2018 Belgian entry to the Tigermeet exercise by converting the 1/72 Tamiya F-16C to an F-16AM using the Revell decals, intake trunk and fuselage spine to get the panels right for an early P&W powered F-16. Everywhere I look on internet, there's a Bill Gilman entry on a forum! 😄 What's your brainwave frequency, so it's easier to directly chime in? 😉
23 April 2021, 15:32
![](/profiles/img/10105-s.jpg)
@Patrick, I'm old school. You need a wire to connect. The plug receptacle is behind my right ear. 🙂
Did you find my finished FRS.1 on Britmodeller? It was a fun kitbash of the Fujimi and Hasegawa kits with a bunch of aftermarket. Come to think of it, it's on here too. For the FA.2, I'll be kitbashing the Hasegawa and Special Hobby kits. Hasegawa will contribute the wings because SH does not have any vortex generators. The Hasegawa FRS.1 wings fit perfectly, and only need a slight mod to the leading edge. It's quite obvious that the SH kit was "inspired" by the Hasegawa kit. Nudge, nudge, wink, wink.
I only do two forums on a regular basis, Scalemates and BM. Once in a while I submit a Gallery article to Hyperscale. If you see me on any other forums - it's an imposter!
23 April 2021, 22:25
![](/profiles/img/18540-402-s.jpg)
Wow, Bill, you get that much?
I gotta' look for a better job.
'Run what you brung'.
Yep, it's the poor musician that blames his instrument.
The add-ons take it to another level. Nice.
23 April 2021, 22:26
![](/profiles/img/10105-s.jpg)
Slow, snail-like progress. I've added some new photos - as you can see I'll soon be closing up the fuselage. I think I should remove the stabilizers first as these will be replaced with some resin items that I've ordered. Cheers, Bill
27 April 2021, 00:03
![](/profiles/img/25429-812-s.png)
Yep, I did! I'm building the old 1/48 Airfix kit for a club member. Not a very detailed kit by today's standard, but for 1983 it's quite good in the main details department. Airfix really did their homework. Either way, I wanted to check some things and came across your 'investigation' over on Britmodeller and from there I kept looking further. Let's see where we meet on that Belgian Tiger then. 😄
27 April 2021, 01:52
![](/profiles/img/13641-502-s.jpg)
"Go for the Academy bug, they said. It'll be fun they said" and then Bill is going to prove Hasegawa can look better 😉 Following. The OOB camo looks cool too.
27 April 2021, 12:21
![](/profiles/img/10105-s.jpg)
Both Hasegawa and Academy do not have the level of detail that is provided by these aftermarket sets. It's been a lot of work so far, but I think it will get a bit easier from here on out. I hope so anyway!
27 April 2021, 14:24
![](/profiles/img/10105-s.jpg)
Hi mates - today I removed the horizontal stabilizers in anticipation of the Quickboost resin replacements arriving from Kitlinx soon. This will allow me to pose the stabilizers in a more natural position. It's a bit tricky removing the stabilizers from the upper fuselage - the innermost edge of each stabilizer is moulded as part of the fuselage sidewall. This portion must be preserved after you're finished with cutting, grinding, and sanding. I added a couple of pictures to show what I mean. Cheers, Bill
28 April 2021, 00:32
![](/profiles/img/10105-s.jpg)
Catching up with my progress - several new photos have been uploaded. I think she's coming along nicely, and it won't be long before I start painting. Let me know if you have any questions. Cheers, Bill
8 May 2021, 01:01
![](/profiles/img/10105-s.jpg)
Well, I finally got the HUD together. You need steady hands for sure. The brackets were tiny! Check out the photos. It's a reasonable facsimile of the real thing. Cheers, Bill
9 May 2021, 00:45
![](/profiles/img/10105-s.jpg)
Thanks, @Spanjaard. I appreciate the compliment. 🙂
OK, here we go - painting has commenced! I added the windscreen to the fuselage and blended it in with a bit of filler. Then some foam was put into the intake to mask off the engine face, some masking tape placed over the cockpit and we're spraying. The white is going down first, followed by the medium blue and finally the dark blue. All demarcations will be by hand - no blue-tac etc. Paints are all Mr. Hobby. Cheers, Bill
9 May 2021, 20:34
![](/profiles/img/10105-s.jpg)
The painting is finished, and the decals have been applied. The new photos I've uploaded show the progress, and some of the issues I found. One was a printing mistake by TwoBobs and the other a big difference in the size of the tail fins between Academy and Hasegawa. After a little trimming, all was good but it makes me wonder which kit is right. Probably neither! Cheers, Bill
21 May 2021, 22:18
![](/profiles/img/10105-s.jpg)
Hi mates, my Centennial of Naval Aviation F/A-18C Hornet is finished and I've uploaded many more photos. The project was bit of a challenge with the Aires resin parts, but it was a lot of fun. I really like anniversary and display schemes, and when they're also retro that makes it even better. I think the USN was going for a "supersonic Hellcat" look when they chose this scheme from VF-17 in 1945. I think it looks a lot better than low-viz grey, but then I'm not the one getting shot at! Cheers, Bill
28 May 2021, 22:44
![](/profiles/img/13641-502-s.jpg)
As I mentioned - better than many Academy builds. That Hellcat 2.0 camo is a real eyecatcher 👍
29 May 2021, 08:51
![](/profiles/img/16661-726-s.jpg)
That traditional livery suits this bird very well, Bill. Very impressive detailwork like always, especially that gunsight is unbelievable !
30 May 2021, 18:04
Album info
1:72 Hasegawa kit with a bunch of aftermarket goodies.