USS Independence

1
December 31, 2021
Since the stock hangar is 4 flat pieces of plastic, with injector pin marks, I’m going to get rid of it and build the hangar from scratch.
2
December 31, 2021
2/3 walls done
3
December 31, 2021
The port side of the hangar bay has much more space for hidden walkways and internal passages, while the starboard side appears to be directly against the exterior of the ships. This is going to make constructing some of the overhead elements difficult.
4
December 31, 2021
I added tie down spots using a hand drill. The styrene taped to the back will be a ceiling for the overhead lighting, even though it’s slightly lower than it should be to scale
5
December 31, 2021
Upper walkway is done. Details still need to be added. Once done, over head pipes and lighting will get added
6
January 3, 2022
I removed part of the top of the superstructure. This will make finishing and closin the hangar much easier.
7
January 3, 2022
More hangar details, I’m starting to add things without reference because of a lack of images
8
January 16, 2022
Railing and ladders finally arrived. The ladder is borderline awful, but it’ll do
9
January 16, 2022
Primer down
10
January 16, 2022
Floor done. Will need to mask and re-spray the walls
11
January 17, 2022
12
January 22, 2022
The firescout will be in the left hangar bay, and a sea hawk on the right. I think I will add some more equipment in the middle between the two hangar bays
13
January 22, 2022
Just waiting on the lighting supplies to finish up the hangar. The tail rotors of the Seahawk are the same height as the overhead pipes, so I’ll need to finish that before closing the bay up as well
14
January 22, 2022
Seahawks and Firescout painted with a glosscoat
15
January 24, 2022
Leds aren’t quite as bright as I thought they might be. They’re also much smaller than I expected
16
January 24, 2022
17
January 24, 2022
I re-set some of the leds, and it has improved the brightness somewhat
18
January 24, 2022
Day time lighting
19
January 24, 2022
20
January 25, 2022
Next update will be the exhaust vents on the super structure. They’re just a pair of recessed holes, so this should be a pretty quick change to give the structure a bit more depth and accuracy
21
January 25, 2022
22
January 26, 2022
Attempt 1: failure. Holes aren’t centered, and I didn’t wait long enough for the glue to dry, so a lot of the layers have tear-out.
23
January 27, 2022
Attempt 2: successful-ish. I bought some 1/4 inch styrene tube for the exhausts. Removing my previous attempt caused damage to other parts of the super structure piece, so there will be more work to fix that
24
January 27, 2022
Hangar is fully closed up now. Some putty will be needed to fill the seam
25
February 8, 2022
After a little break and a bit of thinking, i’m going to put a photoelectric sensor underneath the little platform for the fire scout. I did a bit of testing, and even with the photoetch mesh that will go over it, it will still. Be able to detect sunlight as it should. This will be hooked up to the blue hangar bay lights, and any external lights I may add
26
February 8, 2022
27
March 17, 2022
I’ve cut out locations where i want to install the landing pad lights. A friend is 3d printing some boxes that should host the lights in order to get that nice floodlight look.
28
March 17, 2022
Like I said, my first time wiring lights. Making due without wire strippers, a soldering iron, or any experience
29
March 18, 2022
Note to self: buy soldering iron and wire strippers. I'm not proud of it, but the landing pad lights and hangar bay lights are attached to the photo sensor
30
March 18, 2022
8 landing pad lights. I tried to shorten cables to a necessary length, and ended up tearing the resistor off of one of the lights, so I used a slightly smaller LED for the furthest rear port side light
31
March 18, 2022
Hangar bay and pad lights
32
March 18, 2022
I'm considering building out a lighted bridge. I don't know why, I probably shouldn't, but I'm still thinking of it. This is a 3d model that i'm considering getting printed
33
March 18, 2022
The only holdup on following through with this is drilling out the windows of the original molded plastic, and how I might replace the window "glass"
34
July 8, 2022
I’m trying to fix the shameful mess I made before. As is my luck, I destroyed one of the LEDs, so I will need to order some more before I can finish wiring the landing pad leds. The 3d printed bridge, and boxes to house the pad LEDs have been ordered and should arrive in the next few days.
35
July 15, 2022
Deck light boxes finally arrived. There’s about 50-60 of them total in these two pieces. I will need to go through and clean up some of the extra flash, but these should house the LEDs nicely, and ensure that they look like directional swaths of light
36
July 17, 2022
Good learning lesson, use measurements when creating scale parts. The back wall currently measures at 5mm, which would equal the height of a tall individual. The wall should be ~8mm to be in proper scale. It also seams that the front of the bridge does not match the angle of the inner plastic, so those dimensions will need to be re-drawn
37
July 18, 2022
Deck LEDs are fully re-wired and soldered. The bridge needs to be constructed, and wired. The deck lights need to be fully seated and covered with the boxes I had printed

Comentarios

15 31 December 2021, 02:20

Robert Podkoński
Fantastic work so far! Watching with interest and pleasure 🙂

22 January 2022, 06:17

John Hughes
The LED's look fine to me. My usual complaint with most model lighting is that it is too bright. Everyone would need to wear sunglasses all the time!

24 January 2022, 13:31

Reaper_lead
I think part of it might be how I'm mounting the leds in the ceiling. Fair point on the brightness bit, but I think I would've liked them to be a fraction brighter so that there were a few more details visible.

24 January 2022, 19:01

John Hughes
Let's meet half way and call it the night shift.

24 January 2022, 19:24

Reaper_lead
I think I can handle that 😛

25 January 2022, 22:06

Alexander
Really cool additions with the scratch-built hangar and LED's. Watching. 👍

28 January 2022, 00:10

Reaper_lead
Thanks Alex!

9 February 2022, 14:42

Reaper_lead
I'm trying to light the landing pad. I was hoping that I could somehow get some leds seated underneath the little moulded rectangles so you can see the light beams on the landing pad. I tried drilling a little hole and then covering the top with some styrene. Scale-wise, the lights would be a little too big, and even the pico leds that i'm using 1mm width, are too wide. Perhaps some trickery with little bits of mirror or something like that might be an option

9 February 2022, 14:49

Reaper_lead
It's been a while. The deck lighting boxes have arrived, as has the bridge. I have yet to test the lighting boxes, but the bridge is totally out of scale with the rest of the ship. I will need to re-work it and have it printed again

17 July 2022, 16:30

Project info

LCS-2 USS Independence

37 imágenes

1:350

En espera

1:350 Aerials, Masts & Mk110 (Bofors) 57mm/70 Gun Barrel (Master SM-350-063)

Todos los álbumes

Ver todos los álbumes »