Uutisvirta

Cristian A
Taking a seat and popcorn 🍿

Skyhiker
Welcome Cristian A.

Dave Flitton
Watching

Robert Podkoński
Taking a seat too!

Skyhiker
Welcome gentlemen

Ben M
It is like a duck

Skyhiker
Yeah, it's a bit like the Su-34, just a little less flat.

DerMattes
Watching 👍

Skyhiker
Hi, DerMattes, welcome.

Guy Rump
Following. 👍

Skyhiker
Wings are on and surface details beginning.

Mr D
Coming along nicely 👍👍 More building 🤣 going ahead,
Smart and interesting aircraft, lm going to have to research n watch some YouTube videos on this aircraft.
Like the cockpit 👌

Mr D
Watching a YouTube video on the Berkut now, interesting aircraft 🤔 ..

Skyhiker
Yeah, it's kinda cool. Certainly it's different from the other Russian planes in looks.

Tim
NIce

Villiers de Vos
Steady progress. Did you light the stern?

Thomas Wirsching
Great job so far! I would love to get an explanation about how to do these LED lighting in detail as I have no idea about this.

Hang Li
Thanks Tim, Villiers, and Thomas. I did put a led for the trolled sonar bay back at the stern. It is apparently not bright enough to be really visible. Probably not noticeable after finished.

I prefer to use Led tape light as it has build in resistors so I don't need do calculation to figure out the resistor value. Once that is sorted, what left is just connect the led unit with a battery and a switch. I think it is better to ask a trained electrician as the circiut I built don't last long and I don't really know why.

Michael Kohl
I expect modelling of the highest quality from your bench. So far I am not disappointed. 🙂
Keep it up.

Treehugger
Hm, how long did it take to make the nice looking ocean surface? It certainly looks like a fun project.
I wish I knew how to make such ocean surfaces, as it really seem to complete a model with such a diorama.

I am no expert on led's but my impression is that one has to be careful that the voltage to the led's is controlled to specs, so they don't burn out shortly after and end up being un-repairable inside the model. Also, something about connecting led's in parallel, pattern iirc, to avoid one dead led blacking out all the rest of the leds in a serial connection, iirc.

Thomas Wirsching
Your build is already mindblowing; 漂亮]!

Tim
Your sea base is looking really nice.

Hang Li
Thanks Treehugger, THomas and Tim.
As for the sea base, you can check a YouTube channel called ''studio blue ocean'', I basically followed his videos. And treehugger did a pretty good summary for LEDs. The voltages is very important and it is always needed to put some resistors in series to potect the LEDs. The size of the resistors can be calculated with ohms' law. There are small circuit boards for LEDs which can be used to make everything easier.

Rui S
Impressive work 👍

Villiers de Vos
Fantastic work with all the photoetch parts. Your attention to detail shows.

Thomas Wirsching
Getting better and better; can you please show us a detail picture from the inside of the hangar? Did you build this from scratch?

Hang Li
Thanks, Rui and Villiers. I just masked the hangar as I am going to paint the outside. I will get better hangar photos once finish. The trumpster kit comes with the hangar and the ceiling is in good detail (I only add LEDs to the ceiling). Only the walls need additional work to add details, like handrails, supports etc.

Ingmar Stöhr
Wow! Fantastic detail work and great job on the weathering and the base!

Gary Victory
Really nice work Hang. Looking like a great build.

Villiers de Vos
Fantastic finish.

Ingmar Stöhr
@Hang Li: For the 'oil canning' effect. Did you have accurate plans for the frame spacing or how did you come up with the pattern you used? I have to say that is look really convincing after some more weathering effects are applied on top.

Hang Li
thanks Ingmar, Gary and Villiers. As for the 'oil canning' effect, I found some photos which are somewhat visible for this effect as reference for the pattern and I have to simplifie the pattern to make it practical. So it is not quite accurate. I got some pre-cutted masking paper in 1mm, 2mm, and 3mm and I just picked one that I believe is most suitable.

Ingmar Stöhr
Thank you for the explanation! It looks convincing to me! Keep up the great work!

Michael Kohl
That oil can effect worked really great.

Miguel Vaquero
Amazing build!! Did you use resin for the sea base? If so, how did you manage to make that rough sea surface? It looks amazing

Jörg Schäfer
Great job. 👍

Thomas Wirsching
astonishing build and breathtaking seascape. Hats off to your talent!

Guy Rump
Looking great, following. 👍

Ingmar Stöhr
Looking really convincing so far!

Hang Li
Thanks, everyone. As for the material used for the sea base, I normally use high-density insulation foam (blue sheet from my early photos) and clay. I think many people build diorama this way. I believe there are more sophisticated methods nowadays. I saw someone using CFD modeling to simulate the wave pattern and 3D printing the entiry sea base in Chinese formus.

Ingmar Stöhr
I tried the 3D printing method once, but only for something like 10x10cm, as that is the maximum for my printer and I did not see how I could glue several pieces together without visible seam. The seascape was generated in Blender and I have to say it looked stunning! BUT I feel a lot of the final effect and realism comes from painting and here you are doing a superb job! I will definitely take your work as my inspiration for my next take on displaying water!

Michael Kohl
Absolutely convincing seascape and wake!