Uutisvirta

Patrick Hagelstein
That's a big boy! Curious about what you're going to build.

Przemek Przybulewski
Hi Patrick,

I never was a "phan" of phantom, until I made one 🙂
It was completed long time ago, but I always hoped that I will find a time for another one
12. F-4C/D Phantom II | Album by Pprzybulewski (1:32)

Patrick Hagelstein
Once you get hooked, you'll become a Phan! 😄

Guy Rump
Looking good, following. 👍

Patrick Hagelstein
Welcome along Guy! ☺️

Moreno Baruffini
Super good! Following as well!

Patrick Hagelstein
Welcome aboard Moreno!

Alec K
Very good! Not often-seen livery, looks great Patrick 👍

Patrick Hagelstein
Thank you Alec! For some reason the HAD decals got me hooked too! 😊

Alec K
Well done 👍

Moreno Baruffini
Absolutely well done ✅

Patrick Hagelstein
Thanks Alec and Moreno! 👍🏼

Skyhiker
For a relatively new kit I am surprised on how much flash and fitting issues this kit has.

Skyhiker
It's really hard for me to fight off the urge to correct the structural issues with this kit. But I promised myself I would make this one out of the box.

Patrick Hagelstein
I've seen that promise before Skyhiker! 😂 Good luck keeping this one OOB! 😉👍🏼

Skyhiker
I really hate Revell conopys.

Sergio Ordonez
Mate, I think you should put the windshield uspside down. The ángel does not cope with the real one as I see on photographs.

Skyhiker
Unfortunately it looks even worse the other way around. The idiot engineers at Revell should be fired.

Sergio Ordonez
Well, I had some work with French engineers and I know shit happens. Could you take a photo with this one in the other position?

Sergio Ordonez
drive.google.com/fil..J9/view?usp=drivesdk
The windshield is not an isoscelles triangle so the windshield has not a 45 degree ángel over the capot. Please, see these example of a TA-152 (and please, mind It is 35 years old and I was only 13 when I drestroyed It).
I think an easy solution can be made. I do not want any mate to be anoyed by an engineering issue. I had them everyday (it's my job, Factory engineering problem solving, known as 'shit managing") and It can destroy your mojo.

Ben M
What a terrible canopy

Skyhiker
After several hours of sculpting I got the canopy to fit better. I will continue with it tomorrow.

Sergio Ordonez
Your mojo works, mate! Now you have became a great problem solver!
On the other hand, I think another 3D engineering guy needs to stop drinking and 20 years of 2D drafting. The fitting is worse than I could imagine. But I see is no a problem for a seasoned mate like you. Great work, mate!

Nicolas
Following. I build this kit several times in older versions. The fit of the canopy is realy sh*t. My solution was (with about 10 years) to sand the backside of the windshild till it fitted. Of corse so most of the frame is missing.

Thomas Kolb
What a struggle! It reminds me of some Heller and Amodel kits. But it looks that you manage to coax it into shape!

J35J
Great effort and progress! 👍🏻

Skyhiker
Sergio the TA 152 had a very different canopy than the 190. The 152 was designed for high altitude flying, was pressurized and had double panes.

Sergio Ordonez
Thanks you, Skyhiker: I think I can remember now, as I researched about FW190 and TA152 black in the 90's. Also, canopy is bubble-shapped. Sorry, my FW190 Mustang have been gone forever, I expent the night trying to find It, just to find my solution, but I think only the reta of the TA152 has survived.

Mr D
You done a better job of the seat belts than l did 🤣. The cockpit glass on my model was not very clear!
Looking good, ... Thanks for uploading 👍👍👍

Skyhiker
Mr D did you also have so much trouble with the canopy? I read in the kit review at the bottom of the page that it was bad. I really wish the reviews would be moved up because I always forget about them. It took me quite a while to get the canopy to work. It needed a lot of reshaping to look right.

Skyhiker
I decided to make my own blueprint for this plane. So, that's taking up a lot of my time at the moment.

Mr D
Hi, yes l had trouble too, l did a dry fit before paint, and l had to take a combination off the glass n some off fuselage, and had to use a bit of UV clear resin.
I got it to fit in the end, but it's not very clear to see through.
I had a bit missing of my engine fan too, had to make it up with super glue gell.

Alexander Grivonev
Built one too back in the day, the nightfighter version. Speaking of the canopy, I like how the rear part of it is just molded to the fuselage 😄. Used some other canopy I found in my spares because the one from the kit was entirely unusable.

Mr D
Looking good 👍👍
It's a nice model when it's finished once you sort the shortcomings out.
I did get my prop to spin in the end....had to do alot of work to the cooling fan to make it run smoothly.
Good luck on next steps 😃👍

Skyhiker
If I had thought it would have been a problem I would have dry fitted everything first. But I wanted to keep the parts on the sprue for painting. It wasn't worth messing up the paint job just to get the propeller to spin. Especially since the contact points were so fragile. So in the end I glued it together so it will be stable.

Skyhiker
Working out the fuselage patterns today.

Mr D
Looks good 👍👍

Guy Rump
Looking good. 👍

Mr D
Nice to compare the two.
👍

Skyhiker
I got the legs and nose on and painted the exhaust today.

Villiers de Vos
Very nice progress. Phenomenal paint work.

Skyhiker
I got the decals on today.

Mr D
Nicely done.....looks good now 👌👍👍
You managed to get a correct decal for the tail.... Better.
You got it very close to box art.

Skyhiker
Thanks Mr D.

Mr D
On the fiddly bits... Did you decide to make your own part for that Whip shaped thingy🤣 don't know what it actually is 🫣.... ?
Quite a few little fragile bits on the bottom... I was extremely cutting n sanding these.
Like the way the guns are visible through wheel well's👍

Skyhiker
Mr D, the Morane antenna I built by filing down a wooden toothpick and super gluing a hog's hair on to it that I got from a cheap brush. The kit part was ridiculously out of scale. I use this hog's hair method for whip antennas and static dischargers because the hair is flexible enough that it won't break off.

Mr D
AHH thanks it's Antenna 👍 be better with bit of flexibility... looks more accurate to photos as well.
I noticed HB do a Ta-152 kit....looks quite good for price.. bit of PE in kit.
I was tempted.....but promised myself l will build one buy one 🙄🤣.

Skyhiker
Lol. I promised myself the same thing and the next week someone offered me their entire stash of 45 kits for super cheap, which I bought immediately.

Mr D
🤣... Keep you out of trouble for a while.

Ben M
…. Goes to look at SH's stash …