Shelby Cobra 427 S/C
![Album image #1 Album image #1](/albums/img/4/4/0/496440-16302-75-720.jpg)
Dry fit to see what's what
![Album image #2 Album image #2](/albums/img/4/4/1/496441-16302-19-720.jpg)
![Album image #3 Album image #3](/albums/img/4/4/2/496442-16302-61-720.jpg)
![Album image #4 Album image #4](/albums/img/4/4/3/496443-16302-63-720.jpg)
I wanted to have a clean look so I'll close this holes and not go for any bumper
![Album image #5 Album image #5](/albums/img/4/4/4/496444-16302-64-720.jpg)
closing the bumper holes on the back as whell, with some stretched sprue and sprue glue
![Album image #6 Album image #6](/albums/img/4/4/5/496445-16302-31-720.jpg)
testing some striping tecniques
![Album image #7 Album image #7](/albums/img/4/4/8/496448-16302-56-720.jpg)
oppening the hole for this air exits, I'll scratch build them later
![Album image #8 Album image #8](/albums/img/4/4/9/496449-16302-41-720.jpg)
marking the cutting area
![Album image #9 Album image #9](/albums/img/4/4/6/496446-16302-57-720.jpg)
saving a template for the scratch build
![Album image #10 Album image #10](/albums/img/4/4/7/496447-16302-68-720.jpg)
building a box for the area for scratch build later
![Album image #11 Album image #11](/albums/img/4/5/0/496450-16302-48-720.jpg)
drilling a hole
![Album image #12 Album image #12](/albums/img/4/5/1/496451-16302-60-720.jpg)
![Album image #13 Album image #13](/albums/img/4/5/2/496452-16302-23-720.jpg)
This hole looks too thick, I have to thin it down from inside a bit.
![Album image #14 Album image #14](/albums/img/4/5/3/496453-16302-67-720.jpg)
I´m thinking in using this figure close to the car, looks nice to me 😉
![Album image #15 Album image #15](/albums/img/4/5/4/496454-16302-90-720.jpg)
![Album image #16 Album image #16](/albums/img/4/5/5/496455-16302-41-720.jpg)
1/24 figure from Master Box
![Album image #17 Album image #17](/albums/img/4/5/6/496456-16302-97-720.jpg)
priming and painting
![Album image #18 Album image #18](/albums/img/4/5/8/496458-16302-71-720.jpg)
using tamiya X-13
![Album image #19 Album image #19](/albums/img/4/5/9/496459-16302-66-720.jpg)
![Album image #20 Album image #20](/albums/img/4/6/0/496460-16302-66-720.jpg)
base color painted
![Album image #21 Album image #21](/albums/img/4/6/1/496461-16302-24-720.jpg)
![Album image #22 Album image #22](/albums/img/4/6/2/496462-16302-83-720.jpg)
![Album image #23 Album image #23](/albums/img/4/6/8/496468-16302-44-720.jpg)
The fine stripes are done with 0,3 tape, the finest that I could find, did I ever mentioned how much I hate masking?...
![Album image #24 Album image #24](/albums/img/4/6/9/496469-16302-70-720.jpg)
But I do love to unmask, specially if what I did went right!
![Album image #25 Album image #25](/albums/img/4/6/6/496466-16302-12-pristine.jpg)
I found the gide for the stripes with the pin stripe on the side, the kit one are all paralell, looks wrong to me.
![Album image #26 Album image #26](/albums/img/4/6/3/496463-16302-78-720.jpg)
now, send down the jaged edges of the wite borders and prepare for clear coat
![Album image #27 Album image #27](/albums/img/4/6/4/496464-16302-50-720.jpg)
I also took the oportunity to paint the continuation of the stripe in the lower front of the car, there where no decals for this area.
![Album image #28 Album image #28](/albums/img/4/6/5/496465-16302-99-720.jpg)
the proportions of the stripes looks good to me, I folowed the directions found on internet.
![Album image #29 Album image #29](/albums/img/4/5/7/496457-16302-61-720.jpg)
a bit of scenary composing....
![Album image #30 Album image #30](/albums/img/5/1/7/496517-16302-16-720.jpg)
That´s the result after the gloss coat, it had 2 very light layers and than one heavy coat, there are some orange peel, but it is kind of consistent troughout the model, but it is ok, I'll take care of them with light wet sending and polishing.
![Album image #31 Album image #31](/albums/img/5/1/8/496518-16302-23-720.jpg)
I have used Mr. Color GX112, it is easier to handle than the tamiya gloss clear and dries a bit harder and faster, the stripes have been sended lightly to remove the jaged edge resulted by the masking tape and now all is burried under the clear coat
![Album image #32 Album image #32](/albums/img/5/1/9/496519-16302-61-720.jpg)
I´m going to compare with the result after the sanding and polishing steps, I kinda like the orange peel but it is hard to get it the same in every place, I dont like the idea to build up thick layers of gloss to hide them, it makes the model look toylik
Kommentit
1 21 July 2018, 01:59