panther g build
![Album image #1 Album image #1](/albums/img/0/4/2/792042-73716-49-720.jpg)
Made new weld seams and armor texture because the kit ones were on the poor side. Welds are made out of green stuff two-part epxy putty and armor texture with tamiya putty cement.
![Album image #2 Album image #2](/albums/img/0/4/3/792043-73716-70-720.jpg)
![Album image #3 Album image #3](/albums/img/0/4/4/792044-73716-63-720.jpg)
The the gun didn´t fitt perfectly soo i had to make the hole smaller.
![Album image #4 Album image #4](/albums/img/0/4/5/792045-73716-36-720.jpg)
![Album image #5 Album image #5](/albums/img/0/4/6/792046-73716-65-720.jpg)
Had to scratch build the spare rode wheel holders. These will be corrected later.
![Album image #6 Album image #6](/albums/img/0/4/7/792047-73716-73-720.jpg)
![Album image #7 Album image #7](/albums/img/0/4/8/792048-73716-80-720.jpg)
![Album image #8 Album image #8](/albums/img/0/4/9/792049-73716-14-720.jpg)
This piece had some missing welds.
![Album image #9 Album image #9](/albums/img/0/5/0/792050-73716-80-720.jpg)
![Album image #10 Album image #10](/albums/img/0/5/1/792051-73716-80-720.jpg)
More missing welds on small parts.
![Album image #11 Album image #11](/albums/img/0/5/2/792052-73716-46-720.jpg)
Work in progress.
![Album image #12 Album image #12](/albums/img/0/5/3/792053-73716-76-720.jpg)
![Album image #13 Album image #13](/albums/img/0/5/4/792054-73716-39-720.jpg)
![Album image #14 Album image #14](/albums/img/0/5/5/792055-73716-27-720.jpg)
![Album image #15 Album image #15](/albums/img/1/1/1/811111-73716-95-720.jpg)
the photo edge part in the kit was too thick and the aber one was too small for the RFM kit.
![Album image #16 Album image #16](/albums/img/1/1/2/811112-73716-98-720.jpg)
When i started the kit i cut of some of the parts because i didn't know better. Therefore i had to build new ones for scratch.
![Album image #17 Album image #17](/albums/img/1/1/3/811113-73716-84-720.png)
the aber C hooks where better than the kit ones
![Album image #18 Album image #18](/albums/img/1/1/4/811114-73716-43-720.jpg)
![Album image #19 Album image #19](/albums/img/1/1/5/811115-73716-33-720.jpg)
thinning the vision ports
![Album image #20 Album image #20](/albums/img/1/1/6/811116-73716-17-720.jpg)
these parst needed some filling
![Album image #21 Album image #21](/albums/img/1/1/7/811117-73716-27-720.jpg)
![Album image #22 Album image #22](/albums/img/1/1/8/811118-73716-38-720.png)
mufflers had some fit issues
![Album image #23 Album image #23](/albums/img/1/1/9/811119-73716-71-720.jpg)
![Album image #24 Album image #24](/albums/img/1/2/0/811120-73716-73-720.jpg)
some improvements
![Album image #25 Album image #25](/albums/img/1/2/1/811121-73716-24-720.jpg)
![Album image #26 Album image #26](/albums/img/1/2/2/811122-73716-91-720.jpg)
loaders vision port was too thick in the kit soo i made a new one from sheet metal
![Album image #27 Album image #27](/albums/img/1/2/3/811123-73716-73-720.jpg)
![Album image #28 Album image #28](/albums/img/1/2/4/811124-73716-74-720.jpg)
![Album image #29 Album image #29](/albums/img/1/2/5/811125-73716-42-720.jpg)
more of some improvements
![Album image #30 Album image #30](/albums/img/1/3/9/811139-73716-58-720.jpg)
![Album image #31 Album image #31](/albums/img/1/4/0/811140-73716-46-720.jpg)
![Album image #32 Album image #32](/albums/img/1/4/1/811141-73716-13-720.jpg)
![Album image #33 Album image #33](/albums/img/1/4/2/811142-73716-72-720.jpg)
IR box and left stowage box
![Album image #34 Album image #34](/albums/img/1/4/3/811143-73716-78-720.jpg)
![Album image #35 Album image #35](/albums/img/1/4/4/811144-73716-43-720.jpg)
![Album image #36 Album image #36](/albums/img/1/4/5/811145-73716-93-720.jpg)
![Album image #37 Album image #37](/albums/img/1/6/9/811169-73716-92-720.jpg)
Kommentit
4 16 June 2020, 07:50