Galaxy Quest "N.S.E.A. Protector"
![Album image #1 Album image #1](/albums/img/6/2/7/1036627-86172-34-720.jpg)
Bridge with windows drilled out. Not the funniest work to do...
![Album image #2 Album image #2](/albums/img/6/2/8/1036628-86172-57-720.jpg)
![Album image #3 Album image #3](/albums/img/6/2/6/1036626-86172-60-720.jpg)
Lightblocking coating with ModelAir Aluminium inside and outside.
![Album image #4 Album image #4](/albums/img/6/3/0/1036630-86172-21-720.jpg)
Flatered clear inlets. Nessesery, besause i use the photoetched parts from Paragrafx.
![Album image #5 Album image #5](/albums/img/6/2/9/1036629-86172-12-720.jpg)
Masked inlets and black piece of sheet for the LED, so no light can shine through the plastic. I placed zwo blue 1206-SMD LEDs on a small piece of hole matrix board and attached them on the black sheet. Unfortunalely, i forgot to take a picture.
![Album image #6 Album image #6](/albums/img/6/3/1/1036631-86172-72-720.jpg)
I have to trim a lot of the parts (before and after)
![Album image #7 Album image #7](/albums/img/6/3/2/1036632-86172-33-720.jpg)
After removing material, a white base coating was applied.
![Album image #8 Album image #8](/albums/img/6/3/3/1036633-86172-90-720.jpg)
More removing and painting.
![Album image #9 Album image #9](/albums/img/6/3/4/1036634-86172-14-720.jpg)
And the other side.
![Album image #10 Album image #10](/albums/img/6/4/2/1036642-86172-52-720.jpg)
These are the small inlets in front of the wings near the main hull. It's a shame, they are not made in clear red styrene, so it's really difficult to get light through.
![Album image #11 Album image #11](/albums/img/6/4/1/1036641-86172-37-720.jpg)
I drilled several holes and applied 0,5mm (inletes near the fuselage) and 0,25mm (inlets at the outside of the engines) fiberoptics.
![Album image #12 Album image #12](/albums/img/6/4/4/1036644-86172-56-720.jpg)
The lower wing section ready for assembly. I also add a small Attiny85-Controller inside, für flickering the enginelights and blinking the Anti-Collision-Lights.
In the movie, the Protector had no such ACL. But i like them to much. 😉
In the movie, the Protector had no such ACL. But i like them to much. 😉
![Album image #13 Album image #13](/albums/img/6/4/6/1036646-86172-49-720.jpg)
![Album image #14 Album image #14](/albums/img/6/4/5/1036645-86172-93-720.jpg)
The LED-Board for the forward engines. On the side, you can see 1,0mm fiberoptic for lightning the outer side of the wing. It's very little space there, so for the future i would prefer 0,75mm. Generell space is critical in the wings!
![Album image #15 Album image #15](/albums/img/6/4/7/1036647-86172-31-720.jpg)
![Album image #16 Album image #16](/albums/img/6/5/1/1036651-86172-28-720.jpg)
I had to remove some material inside, so i can get the cables and fiberoptics to the center of the ship. I use 0,05mm² wire, but that's a little to thick. For the future, i will use some enamelled copper wire, which is much more smaller. The current is very low, so that should be no problem.
![Album image #17 Album image #17](/albums/img/6/5/2/1036652-86172-51-720.jpg)
Material removed on the other inside.
![Album image #18 Album image #18](/albums/img/6/5/3/1036653-86172-20-pristine.jpg)
The fuselages. I drilled a lot of 0,5mm holes and installed fiberoptics. After that, i use a white 5mm LED, put a piece of polystyre tube on top, and use PVAC glue for fixing. Don't use superglue! It will destroy the plastic fiberoptics.
![Album image #19 Album image #19](/albums/img/6/5/4/1036654-86172-76-720.jpg)
The base is made of wood.
![Album image #20 Album image #20](/albums/img/6/5/5/1036655-86172-23-720.jpg)
Lower side of the base.
![Album image #21 Album image #21](/albums/img/6/5/6/1036656-86172-80-720.jpg)
A Power-Switch and plug-in socket for power.
![Album image #22 Album image #22](/albums/img/6/5/8/1036658-86172-14-720.jpg)
![Album image #23 Album image #23](/albums/img/6/5/7/1036657-86172-31-720.jpg)
![Album image #24 Album image #24](/albums/img/6/5/9/1036659-86172-88-720.jpg)
![Album image #25 Album image #25](/albums/img/6/6/0/1036660-86172-43-720.jpg)
![Album image #26 Album image #26](/albums/img/6/6/1/1036661-86172-27-720.jpg)
![Album image #27 Album image #27](/albums/img/6/6/2/1036662-86172-99-720.jpg)
![Album image #28 Album image #28](/albums/img/6/6/3/1036663-86172-25-720.jpg)
![Album image #29 Album image #29](/albums/img/6/6/4/1036664-86172-86-720.jpg)
![Album image #30 Album image #30](/albums/img/6/6/6/1036666-86172-62-720.jpg)
![Album image #31 Album image #31](/albums/img/6/6/8/1036668-86172-18-720.jpg)
Here you can see the red glowing of the inlets in the wings and by the outsides of the front engines.
![Album image #32 Album image #32](/albums/img/6/6/9/1036669-86172-99-720.jpg)
![Album image #33 Album image #33](/albums/img/6/7/0/1036670-86172-30-720.jpg)
![Album image #34 Album image #34](/albums/img/6/7/1/1036671-86172-96-720.jpg)
![Album image #35 Album image #35](/albums/img/6/7/2/1036672-86172-68-720.jpg)
![Album image #36 Album image #36](/albums/img/6/6/5/1036665-86172-34-720.jpg)
Kommentit
6 22 July 2021, 14:50
![](/profiles/img/61283-429-s.jpg)
Very well done, beautiful in fact. You went through a lot of trouble, and it paid off. ?
22 July 2021, 18:16
Album info
This was a Fastbuild, cause it was planed as present, and i have started the build to late. So, i'm not really satisfied with the result. That's also the reason, why i missed some pictures: The clock was ticking, so i forgot at some stepy, to take pictures.
I've another kit, which i will build later with some improvements. Generall, the kit is quiet good. Fitting is excellent, but the decals are a little bit fragile. Maybe they are to old, the kit was on my stash for many years. So use decal fixing solution, before you place them.