Fil d'information

Mike Brooke
marqué cet article comme sur commande

GMC CCKW 750 gallon Tanker

HobbyBoss 1:35

83830 2014 Nouvelles pièces

13 October, 06:17

Frank Krause
Added a new review for:

Sd.Kfz. 234/4 Schwerer Panzerspähwagen 7,5cm late Interior Kit

MiniArt 1:35

35427 2024 Nouvelles pièces

Examen en boîte

Panzer Modell

13 October, 06:17

Mike Brooke
marqué cet article comme sur commande

Concrete Mixer Set

MiniArt 1:35

35593 2019 Nouvel outillage

13 October, 06:17

Frank Krause
Added a new review for:

Black Eagle Object 640

Amusing Hobby 1:35

35A064 2024* Nouvelles pièces

Examen en boîte

Panzer Modell

13 October, 06:16

Mike Brooke
marqué cet article comme sur commande

Construction Set Ladders, Table, Buckets, Bricks, Cart, Anvil, Beams, Jack Stand & Tools

MiniArt 1:35

35594 2019 Nouvel outillage

13 October, 06:16

Mike Brooke
marqué cet article comme sur commande

Diorama-Base: 'The Factory'

RT-Diorama 1:35

35282 2019 Nouvel outillage

13 October, 06:15

Marcin G.
veut cet article

Ju-88 A-4 Limited Edition

Italeri 1:72

1018 200a Nouvelle boîte

13 October, 06:13

Marcin Dudek
a ajouté un nouvel album photo.

24 images

T-55

Nouveau: 12 October, 17:22

1:72

Projet: T:55

23 15 September, 15:32

Marcin Dudek
A new build starte 🙂. It seems quite easy but one thing puzzles me - the tracks. They compose of 4 straight plastic parts and instruction says to bend them with hair dryer. It is first time I encountered this type of tracks. Anyone tried doing something like this?

15 September, 15:36

Snake Plissken
I have heard of this type of assembly but have never built one. However, I have lots of experience heating and softening styrene plastic. You can also try very hot or boiling water -- soak the tracks in boiling water, then fish them out of the water with long tweezers and bend them around the rear sprocket, idler and road wheels and hold until they cool. You may even get by using no heat, just slowly and carefully bend curves into the tracks.

15 September, 20:46

Marcin Dudek
Thanks for help Snake! That tip is very helpfull 🙂

16 September, 04:35

Guy Rump
Following. 👍

20 September, 17:45

Marcin Dudek
You're welcome Guy 🙂

20 September, 19:46

Marcin Dudek
After some work done I need to say I am a little disappointed with this kit. Instruction includes some mistakes and it is not always easy to read how and where exactly a specific part should be located. More over I expected more from new molds (parts require a lot of work to remove additional plastic).

22 September, 13:17

Snake Plissken
Hi Marcin. My advice is to *expect mistakes* and do your research accordingly. It may or may not be fun to research the T-55 but most of the photos or line drawings you can find online are free, it just takes some time.

25 September, 04:46

Marcin Dudek
Sure thing Snake 🙂. References in the Net are more than sufficient.

25 September, 17:29

Snake Plissken
Good job adding the injector lines on the engine. I overlooked it the first time. 👍

1 October, 05:53

Marcin Dudek
Thanks Snake 🙂. I was considering adding some more parts to the engine but they wouldn't be visible after assembly so I left it as it is. Thanks one again for the track bending tips, they were very helpfull.

1 October, 15:48

Marcin Dudek
Some job with wearhering done. Still, I forgot to apply the decals first 🤦

7 October, 05:41

Marcin Dudek
I call it done.

12 October, 17:23