Fil d'information
scautomoton
possède cet article
possède cet article
BAC
TSR.2 - Intake FOD Covers & Exhausts for Airfix CMK (Czech Master Kits) 1:72
7189 2011 Nouvel outillage 16 August, 13:23
Dmwilde
veut cet article
veut cet article
Kawanishi H8K2 Type 2 Flying Boat Model 12 '901st Flying Group'
Hasegawa 1:72
02473 2024 Nouveaux décalcomanies 16 August, 13:17
Charles-Henri Titelion
veut cet article
veut cet article
Leopard C2 Mexas w/ Dozer Blade Canadian Main Battle Tank
Meng Model 1:35
TS-041 2018 Nouvelles pièces 16 August, 13:17
Bill C
will attend
will attend
Modelpalooza Saskatchewan 2024
18-20 Octobre 2024
18-20 Octobre 2024
15 August, 20:38
Ken Kolenovsky
Not sure where this listing came in Bill, but it is not the one I put on Scalemates. This one is listed under "Group Builds" and that isn't what I set it up as. I also see that there is a link to our Facebook site, but I didn't enter that. Curious.
Not sure where this listing came in Bill, but it is not the one I put on Scalemates. This one is listed under "Group Builds" and that isn't what I set it up as. I also see that there is a link to our Facebook site, but I didn't enter that. Curious.
16 August, 13:16
Simon Smith
possède cet article
possède cet article
Panzer Kampf Flugzeug 40
Fledermaus aka. Jagd Flugzeug 40(S) Nitto 1:20
SF3D Series 11 1984 Nouvel outillage 16 August, 13:15
Alex Rakhimgulov
a ajouté un nouvel album photo.
a ajouté un nouvel album photo.
23 27 June, 09:04
Villiers de Vos
Very nice texturing and weld marks on this Soviet beast. The photo etch details is a nice touch.
Very nice texturing and weld marks on this Soviet beast. The photo etch details is a nice touch.
10 July, 02:10
Alex Rakhimgulov
Thank you, Mate! This photo etch is selfmade from 0.2mm brass plate ))) I need to buy the photo etch bender, to make it better. ))
Thank you, Mate! This photo etch is selfmade from 0.2mm brass plate ))) I need to buy the photo etch bender, to make it better. ))
10 July, 07:14
Alex Rakhimgulov
Thanks, Mate!
I try to make weld beads like on my favorite YT cannel )))
1) I make a groove with scraiber, if it necessary on the plane surfaces.
2) Next, i prepare 2 component putty, and make a thin "laces" out of it.
3) After that, I carefully fill the grooves and angles with putty "laces" and apply welding texture with special tool (toothpick with tip warped with brass sheet, witch forms small speared C shape).
That is all.
Thanks, Mate!
I try to make weld beads like on my favorite YT cannel )))
1) I make a groove with scraiber, if it necessary on the plane surfaces.
2) Next, i prepare 2 component putty, and make a thin "laces" out of it.
3) After that, I carefully fill the grooves and angles with putty "laces" and apply welding texture with special tool (toothpick with tip warped with brass sheet, witch forms small speared C shape).
That is all.
9 August, 09:30
Landlubber Mike
a ajouté un nouvel album photo.
a ajouté un nouvel album photo.
46 images
MyAlbumNouveau: 16 August, 01:32 1:72
This picture is of BuNo 1063 - the subject I will be modeling. Very famous plane - was one of the ten JRS-1s that survi...
Projet: Sikorsky JRS-1 (Eduard)
35 2 February, 15:21
Lochsa River
have to sit in...this is in the stash...I was looking at it yesterday...
have to sit in...this is in the stash...I was looking at it yesterday...
25 February, 04:13
Landlubber Mike
Thanks for following guys. Lochsa, you're right about the canopy. There are fit issues in general with this kit - most of which aren't too difficult to deal with - but the canopy is a bit of a mess. I'm not really looking forward to that part of the build.
Thanks for following guys. Lochsa, you're right about the canopy. There are fit issues in general with this kit - most of which aren't too difficult to deal with - but the canopy is a bit of a mess. I'm not really looking forward to that part of the build.
25 February, 17:33
/fr/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=fr
35
35
/fr/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo