Fil d'information

Robert Podkoński
Wow! This is going to be a true masterpiece... Watching with pleasure and interest!

Ben M
🤯

CaptGPF
That PE work is insane! Gotta watch this!

Michael Kohl
Very interesting project

Pietro De Angelis
😲

Nicolas
Following

Thomas Kolb
Looks neat! the photo-etched details make quite a difference.

Mr D
Nice, like it.
Engine cowling looks nice 👌
Doing good job 👍👍

Łukasz Gliński
Neat start 👍

Lincoln Pennell
looking Good

Mr D
Coming along nicely👌, can see shading on panel lines.
Nice little project 👍👍

Doubtingmango
So I just finished this little Italian job. The decals came out with a lot of the edges showing, which then got a lot worse when I added some washes. I used Microset on the decals, and then sealed them with Tamiya semi-gloss before the washes, but it actually looks like the washes got under the decals. Any thoughts?

Bogicevic Vladimir
It looks like you haven't spray gloss coat before you applied decals. Or decals didn't set well. There are two solutions. One is lacquer thinner. Put the thinner with fine brush in dots over the place where you have silvering. Thinner should destroy the film. If it raises paint under, just leave it, it will settle back. Important thing here is that, once you applied thinner, you shouldn't touch decal for something like 20 minutes, at least. Second way is mix of sugar and water, half - half. You make a hole with a needle on the decal, than you put mix on the top. It should enter in the space between decal and paint and, when drayed, make a gloss film in between them which will act as a gloss under the decal. Wipe excess mix with wet cloath and you are done.

Mr James
How annoying. I've never heard of the sugar water trick from Bogicevic. I'll be interested if this works. If the thinner, sugar trick fails, what else can you do but use a scalpel to cut around them, since you've sealed it,

Mr James
Oh, nice paintjob by the way

Doubtingmango
Thanks mates! I believe Bogicevic is right. I think I did fail to gloss coat before the decals. I think I'll try the sugar water first

Bogicevic Vladimir
Ok. There are few small tings I should add then. Heat the water first, when hot it will disolve sugar beter and apply it while it's still warm, it will have more viscosity. Make small hole or slice with modeling knife, put few drops of mix on the top and let it dry. You will see emidiatly if it's penatrating. When dry, wipe carefully excess mix with moist cloth. Repeat where neaded. I know it sounds ridiculous, but it worked for me many times.

Doubtingmango
Thanks Bogicevic! I'll give it a shot. If it doesn't work I'll try the lacquer thinner technique. I love this site!

Mark Sherwood
Where the *uck's this been hiding. Very nice build Mr Mango and I hope the decal solution from Bogicevic work's out🤞

Doubtingmango
Thanks Mark! So I punched some holes in the decals and applied the warm sugar water, but unfortunately it did not seem to make a noticeable difference. I decided my best shot was to just grab the scalpel and remove the decals, which was very easy. Bogicevic said the solution would get under the decals! I have successfully applied new decals, and my little Italian job is now base-worthy. New pics to come.

gorby
I like that. Excellent weathering.

Robert Podkoński
I agree with Gorby. Good job!

Bogicevic Vladimir
Thank you mates

Pietro De Angelis
Beautiful!

Neuling
Excellent! 1/72!

Paulo Castro
Thanks mate

Łukasz Gliński
Impressive job 👍

Ricardo Reis
Nice one! 👍

Alex Rakhimgulov
In the War Thunder game this plane has very distinct sound. ))) Great project!

Ekki
Excellent result!

J35J
Great job!👍🏻

Pietro De Angelis
Beautiful!

James C
Nice work 👍

Palo M
Beautiful

Mr James
Lovely stowage and a great build

Doubtingmango
Great camo and stowage

Pietro De Angelis
Great work, congrats!