Fil d'information

Sy Bar
Was going to do the Battle of Britain version of this kit but I'm temped to have a go at some winter white wash and the wasp is cooler than the shark mouth 😎

Nicolas
Following

István Szücs
I also have Bf-110 from the Airfix, I will build an Italian night fighter. The sprues are the same, so I'm watching!

Sy Bar
Cheers guys.
I'm have a go at riveting, but going freehand as at this scale using tape was taking so long. I also not sure how much they will stand out on finish kit, but with the wonky line in parts they will probably bee seen from mars 🤣

Mark Sherwood
Looking good so far, like the underside. 🥸👍

Sy Bar
Cheers #Mark

Skyhiker
Sy, how was the fit on this kit?

Guy Rump
Looking good, following. 👍

Sy Bar
Cheers #Guy 👍
#Skyhiker I found the fit to be good, I had a very slight gap at the front but think that was as much to do with me and the fitting of the pit (not the clearest instructions there). Every thing else was fine and the canopy was a good fit, I did change order of build slightly with the tail section I glued the rear piece to the body first then added the tail (after I'd added the stabilisers/rudders) this made more sense than the instructions 😁

Sy Bar
Only issue I have with this kit are the decals. While they look great and are in perfect register, they have a large amount of film edging and are both thick and delicate at the same time🤪
Having a hard time getting them to settle into the panel lines etc. I usually just need to use micro sol but even ultimate extra strong is not have much effect. Going to have to wait till I get some Tamiya fixer, strong and extra strong hopefully one of these will help 🤞

Mr D
You should be ok with the medium one with Airfix decals,
I like a mix of Water in with the markfix...seems to keep the decal floating longer.
I did the teeth on my p40 this way.
If they started getting bit sicky...l would add bit more water....keep it floating.
Wouldn't like to do shark teeth with HB decals 🤔🤣.... The lightning ⚡ strike on my mig-15 just fell apart with hardly any working.
Good luck with it ..look forward to seeing 😃👍👍

Dave Flitton
Looking good!

Sy Bar
Cheers for advice #Mr D. Afraid this set of decals were unaffected by all solutions but the mark fit super strong did have some effect. To make head way I found I needed to add the solution then after a few seconds apply hot air from a hairdryer to 'shrink wrap' the decal. These have to be the worst decals I've come across..
I recommend anyone doing this kit to source a set of decals rather than use those provided, they are not for beginners that's for sure. I hope the carrier film will disappear under a gloss coat but I didn't want to risk it so I've only applied the larger decals the smaller ones while add great detail if cartograf here they are 90% carrier film.

Skyhiker
Why don't you just cut the carrier film away with a knife before applying them?

Mr D
Hi Sy
That's ok .... I think the result will be fine after a clear coat, you come out of it without wrinkles, bubbles or tear's so it's a win, very smart n be sorted under a clear.👌👍👍

Sy Bar
Cheers #Mr D
#Skyhiker that's idea but life's too short for the amount there is, the size of the decal that's left will look like small black dots everywhere (especially the fuselage rib numbers 🤪); would be ok in 48 but too much in 72. Also I'm probably going to much it all up when I apply the winter white wash 😆

Rui S
That's Looking Great 👍

Spanjaard
are you going scratch build it? i am in!

jan zumack
Hi spanjaard, yes i do. This ist a complete Scratch build. At the end the ship will be 790mm Long. I am crazy, i now.

Robin (WhiteGlint)
👀 Ohhh, following this one. 👍

Torsten
Exciting 👀

Shar Dipree
Following! 👍

jan zumack
Welcome Torsten, Robin and Shar 🤗

gorby
WOW! Very ambitious build.

Villiers de Vos
Fantastic work.

jan zumack
Hi Villiers 😁 Welcome gorby, yes it is 😅

Vincent
This is looking amazing. Very nice subject and building skills till now. Looking forward to see where it is going.

jan zumack
Welcome Vincent, thanks for you words.

Ingo F
Oh scratch build, I am in!
May the modeling force be with you. 😄

jan zumack
Welcome Ingo, 😀

Ben M
I definitely want to watch this. The scratchbuilding looks great. Yes, this project will definitely take some time to complete.

jan zumack
Hi Ben, yeah it will. At now i build ca 30 hours.

Freak
What an incredible project! This looks like a masterclass in scratchbuilding, can't wait to see what's next!

jan zumack
Hi Freak. I give my best. 🤘

Zach Wilson
looking good so far

CaptGPF
Damn! Can't wait to see the final result!

jan zumack
Welcome Zach and CaptGPF. 🤗

Alexander
Holy.. this looks amazing so far!👍👍
Definitely watching how this unfolds!

jan zumack
Welcome Alexander.🤗

Stephan H.
This is so great! I am throwing my 3D printer out of the window and try learning something here 😉
I also loved the ship design and how parts move during flight.
Viel Erfolg

jan zumack
Hi Stephan, i do it oldschool because i didnt have a 3d printer. 😂

Torsten
Awesome, I like old school ^^

jan zumack
Thanks Torsten 😁

Pepe
Wooow!!!! huge work

jan zumack
Hi Pepe, yes it is😅

Hans
School of scratch building.

jan zumack
Welcome Hans, yeah i'm in the school. 😅

Torsten
Still impressive 😎

jan zumack
Thanks Torsten, it grows Bit by Bit.

Hans-Jürgen Haag
Extrem scratch work, I like is👍👍👍🥇

jan zumack
Welcome Hans-Jürgen, thanks for your words.

Jörg Schäfer
Craziness. Great scratch work. I'm excited. 👍

jan zumack
Hi Jörg, thanks you.

Rando
Just super impressive, excited to see all the progress.

David Taylor
Watching.

Davide Vitali
This is insane. I like it!!

jan zumack
Hi Guys. Thanks for your comments. 😁

Kyle DeHart
Oh my. Watching with interest. Incredible.

jan zumack
Hi Kyle, Hope you enjoy it.

Sam S
Out of this world build, bring out the popcorn! 🍿

jan zumack
Hi Sam and thanks you. 😁

Dash Rendar
Hot damn, very nice! Love it.

Treehugger
Final model looks like it might perhaps be heavy, can the landing gear handle the weight?

jan zumack
He treehugger, i tested the legs with 2kg per leg, i hope it is enough. If its not i drill in a seperat roundsteel to Catch the weight.

Lochsa River
checkin this out....

jan zumack
Welcome Lochsa. 🤗

Uwe Kaeding
This is looking fantastic - looking forward to see where it goes.

Peter G
No 3D printer? Are you using a cutting machine? How do you get such precise cuts? Loving it!

jan zumack
Hi Uwe, hi Peter,

jan zumack
I use an old drawing bord to Cut the pieces i need. And Stripes, tubes and rods from evergreen.

Lukas Muller
wow !!!

jan zumack
Welcome Lukas 🤗

Jennifer Franklin
This is an impressive undertaking, following 👀

jan zumack
Hi Jennifer. 🤗

Jennifer Franklin
Hi jan. 🤗

David Taylor
Time and patience,brill.

Spanjaard
insane detail.... amazing.

Skyhiker
Great project

Rui
I have no idea how I missed this build!!! 😲
Following !😁

Skyhiker
I'm sorry but this is WAY too cool. It just keeps getting better and better.

jan zumack
Thank you all for your kindly words. I am suprised by my self of the result of the Projekt so far.

Dash Rendar
Damn, those tiny pipes around the jet exhausts. Very cool.

Skyhiker
Picture 210 looks like a boom box. I wonder what kind of funky music would come out of that?

Vincent
This build is looking great. Im looking forward to the painting phase!

jan zumack
@ skyhiker, the Cantina band! :⁠-⁠)

jan zumack
Thank you Vincent.

Shar Dipree
Awesome work! Absolutely fantastic.

jan zumack
Thanks Shar. 🤗

Ian Doody
Excellent scratch build. Brilliant work.

jan zumack
Thank you Ian, i give my best.

Treehugger
What marverous stuff. 🙂

Robin (WhiteGlint)
Amazing progress Jan 👍

jan zumack
Thank you Robin. 🤗

Skyhiker
Funny, that boom box you're making looks like a spaceship.

jan zumack
😂😂😂

NLAWScametovisit
Using your build to show my coworkers how awesome this hobby can be

jan zumack
Yeah do this NLAW. 👍

S M
Incredible job here!

jan zumack
Thank you S M i will continue soon. 😁

Bzmily
Incredible work🥰

jan zumack
Thank you Bzmily 🤘

Alec K
Wow, just found this and what an incredible project! Just fantastic, thank you for sharing it here 👍

Christian Lehmann
Excellent! How could I miss this till now?

jan zumack
Thank you Christian, i go on vacation now, i am back in few weeks.

Finn
Following

Dave Flitton
Watching

J35J
I'm in👍🏻

Cuajete
A classic old and hard kit from Łukasz... I can't miss it!

Patryk S.
Following! Is this build an indication and warning of an incoming Czapla build?😜 Greetings!

Maciej Bellos
Oh, gotta see this one!

Moreno Baruffini
Oh wow! Following!

Mr D
Nice 👍👍

Nicolas
Count me in as well.

Łukasz Gliński
Welcome everyone, glad to have you on board.
@Patryk: LOL, it is waiting in the stash indeed, but I'd like to train some tricks on Łoś and RWDs 6&8 first 😄

Andrzej Rygiel
Insert "I was there 3000 years ago" meme 😄 I got this as a souvenir from our family trip to Poland back in the 80's and finished it in one afternoon sitting straight after our return. I do not doubt you are going to make much better PZL.37 replica than I did back then...

Alec K
Ahh, I have this thing somewhere, in glorious blue. Watching, of course.

Ben M
👀 just what I like

Mr D
Nice to do a vintage kit... takes you back.
I remember doing the Matchbox Electric lightning ⚡ with my dad as a boy..
Good luck with everything 👍👍

Robert Podkoński
Somehow I missed that... taking a seat, of course! (I kinda "built" this kit three or four times as a kid...)

Zbynek Honzik
Beautiful! More photos, please.

YZMA
Hi! Zbynek.
Upload photo.

Robert Podkoński
Great job indeed!

Ben M
Delightful.

YZMA
Hi! Ben.
Thank you.

Robert Podkoński
So sweet!

Robert Podkoński
"Not very carefully done"... Looks perfectly done IMHO 🙂

Neuling
Looks very good!

Rui S
Great weathering Work 👍

Findus
Hallo Rui und Neuling. Vielen Dank für eure Feedbacks.

Robert Podkoński
Good job indeed!