Fil d'information
Arif Saeedpossède cet article
USAF F-16D "Mig Killer" Special Paint Scheme 2022 Decals & Masks
Galaxy Model 1:48
D48062 2024 Nouvel outillage 4 July, 00:28
ICM 1:48
Ghigo73veut cet article
Supermarine Spitfire Mk.I & Light Utility Car 10HP Tilly Set
Tamiya 1:48
25211 2023 Ensemble de modèles Multi sujets (2)4 July, 00:25
hehea terminé cet article
MG Gundam 00
GN-005 Gundam Virtue Celestial Being Mobile Suit Bandai Spirits 1:100
5061788 (2553523) 2021 Nouvel outillage 4 July, 00:24
Micah Marshveut cet article
Viggen Weapon Set for FoxOne Design Studio Viggen kits
FoxOne Design Studio 1:144
B025 2024* Nouvel outillage 4 July, 00:20
Micah Marshveut cet article
Virginia class Block III Nuclear Submarine
USS Indiana SSN-789 Resin & 3D Model Kit Iron Shipwrights 1:350
4-293 2024 Nouvel outillage 4 July, 00:20
Micah Marshveut cet article
TBD Devastator Yellow Wing Paint Masks
Hawaiian Air Depot 1:32
HAD32014 2024 Nouvel outillage Numérique: Fichier de données 3D4 July, 00:20
Micah Marshveut cet article
People's Liberation Army Navy
Type 003 Aircraft Carrier CV-18 FujianMagic Factory 1:700
1008 2024* Nouvel outillage 4 July, 00:19
Micah Marshveut cet article
A-10C Thunderbolt II Demonstration Team Vietnam Scheme
Hasegawa 1:72
02478 2024 Nouveaux décalcomanies 4 July, 00:19
Micah Marshveut cet article
German 75mm Barrel for KwK40L/43 with single baffle muzzle brake for Pz.Kpfw.VI, Ausf.G - Early
Aber 1:35
35L-322 2024 Nouvel outillage 4 July, 00:18
Joepossède cet article
203mm Barrel + Hydraulic pressure rod for 2S7M for Trumpeter
Orange Hobby 1:35
G35-133-96 2015 Nouvel outillage 4 July, 00:15
Desert Marlina ajouté un nouvel album photo.
40 images
Israeli P-51D D-191 (2302)
1:32
Time to finish the cowling. Best way to mask the engine!
Projet: P-51D Israeli D-191 (2302)
32 14 April, 21:47
Desert MarlinWell, the polycap that is supposed to link/sync the left and right elevators fell out during the process of joining the fuselage halves. So I had to saw out the little housing that was supposed to hold the polycap in place and set it manually. Looks like I have one "unforced error" so far...
26 April, 22:57
RandoThat Merlin is looking great. Looks like it came with the kit? Must be a lot easier than old resin, lol
27 April, 00:09
Desert MarlinIt's close to time to add the canopy and mask for paint. Lots of weathering yet to go. And the gun bays are looking a bit bland. Needs some additional paint and wiring.
1 May, 06:15
Desert MarlinTime to close up the cockpit and prep for paint. Going to be one of those traditional natural metal schemes with lots of wear and tear...
3 May, 05:06
RandoYep agreed Ky, my next P-51 will definitely be a Tamiya. How did detailing the gun bays go Marlin?
3 May, 14:37
Desert MarlinStill working on them. The fit has had only one issue that was even close to being worth mentioning. The right wing gun port on the leading edge did not fit perfectly. So I have had to do a little filling on the undersurface. The underwing scoop was almost an issue but seems to have settled into place. WARNING: one must fit the AILERONS BEFORE THE FLAPS. Otherwise the photo etched hinge does not get locked into place by the steel shaft from the outboard end of the flap. Missed this so it was unforced error #2...
3 May, 20:53
Desert MarlinOkay, after looking at some of the real aircraft, I am not sure there is any detail needed except to weather the bay and guns. I was expecting some electrical or other pipes/wiring, but alas, there does not appear to be any...
3 May, 21:41
Desert MarlinI'm back! So the masks provided are intended to be applied to the outside surface. However, it's really hard to mask the interior surface, so I cut the masks and applied them to the inside of the glass and then used Scotch tape for the outside. Leaving the interior a little "over masked, the black primer added to the outside with the flat black interior will create a nice effect overall.
2 June, 23:44
Desert MarlinBack at it! Prop is done, not yet weathered. Needs some scuffing along the leading edges.
1 July, 04:14
Joepossède cet article
M1A1/M1A2 T-158 "Big Foot" Workable Track Link
Rye Field Model (RFM) 1:35
RM-5009 2017 Nouvel outillage 4 July, 00:14
/fr/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=fr
35
35
/fr/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo