WIP: Eurocopter BK-117 "Space Design" D-HBKS
![Album image #1 Album image #1](/albums/img/6/7/2/1754672-25743-83-720.jpg)
The Kit
![Album image #2 Album image #2](/albums/img/6/7/0/1754670-25743-27-720.jpg)
Sprue "1"
![Album image #3 Album image #3](/albums/img/6/7/1/1754671-25743-46-720.jpg)
Sprue"2"
![Album image #4 Album image #4](/albums/img/6/7/3/1754673-25743-99-720.jpg)
Clearsprue
![Album image #5 Album image #5](/albums/img/6/7/4/1754674-25743-36-720.jpg)
Decals
![Album image #6 Album image #6](/albums/img/6/7/5/1754675-25743-73-720.jpg)
Instructions
![Album image #7 Album image #7](/albums/img/6/7/6/1754676-25743-28-720.jpg)
Details Exterior
![Album image #8 Album image #8](/albums/img/6/7/7/1754677-25743-44-720.jpg)
Details Inside
![Album image #9 Album image #9](/albums/img/6/7/8/1754678-25743-23-720.jpg)
Detail Seats
![Album image #10 Album image #10](/albums/img/9/6/6/1762966-25743-24-720.jpg)
I started by removing the ejector pin marks on the cabin inside...
![Album image #11 Album image #11](/albums/img/9/6/7/1762967-25743-75-720.jpg)
... and assembling the tail.
![Album image #12 Album image #12](/albums/img/9/6/5/1762965-25743-86-720.jpg)
The seats gor open backrests...
![Album image #13 Album image #13](/albums/img/9/6/8/1762968-25743-82-720.jpg)
wich I closed for the first 2 rows.
![Album image #14 Album image #14](/albums/img/9/6/9/1762969-25743-43-720.jpg)
I don't like tail-sitters -> some lead inside of the pedestal
![Album image #15 Album image #15](/albums/img/9/7/1/1762971-25743-77-720.jpg)
The step in the roof section is closed with sheet, the gaps filled with putty.
![Album image #16 Album image #16](/albums/img/9/7/0/1762970-25743-98-720.jpg)
OOB the rotorshaft would go down inside the cabin, so I had to modify it a bit. The rotor control also looks quite monolithic.
![Album image #17 Album image #17](/albums/img/9/7/2/1762972-25743-91-720.jpg)
So I removed some unnessasary material and replaced the shaft with a 0.8 mm hypodermic needle
![Album image #18 Album image #18](/albums/img/9/7/3/1762973-25743-26-720.jpg)
While I was at it I started assembling the main Rotor.
![Album image #19 Album image #19](/albums/img/9/7/4/1762974-25743-90-720.jpg)
Dry-fitting showed some problems between the tail and the cowling (the angel between the cowling rear face and the tail-boom front part is about 8°). I hope matching the build groups is easier than the seperat parts.
Commentaires
5 24 June, 19:12
![](/profiles/img/25743-467-s.jpg)
As soon as I finish one of my 3 current projects (2 of them ar nearly done) I will start with this little helicopter.
24 June, 19:17
Album info
Build proces for my 1/72 Eurocopter BK-117 in Stunning Space Design colours designed by Luigi Colani. The Kit is based on a 1988 Matchbok kit and there is no detail set or a kit from better moulds that I know of. So I'll try to improve this oldie a little bit.
I'm going to present the helicopter on a helipad in a city with 2 pilots waiting for some VIPs.