Viking Night Attack - WIP
![Album image #1 Album image #1](/albums/img/4/0/2/889402-48987-49-720.jpg)
WSO Instrument cover - was just a single, straight, open piece. but quite easy to fix with sheet
![Album image #2 Album image #2](/albums/img/4/0/3/889403-48987-63-720.jpg)
Using Eduard PE here. The kits main instrument panels were good, the side panels: meh.
I painted the screens gloss black/green since this will be power off.
For my liking they colored their PE a bit too bright, like very light dark ghost gray, but there will be wash
I painted the screens gloss black/green since this will be power off.
For my liking they colored their PE a bit too bright, like very light dark ghost gray, but there will be wash
![Album image #3 Album image #3](/albums/img/4/2/3/889423-48987-91-720.jpg)
No L-Brackets on this newer airframe model since they use internal stiffeners. (But there are earlier BuNo USMC D-Models that still have the brackets!)
Cut these up and used them for the 3 little support plates on both sides
Cut these up and used them for the 3 little support plates on both sides
![Album image #4 Album image #4](/albums/img/4/0/4/889404-48987-62-720.jpg)
Sanded down the weird round fin tips. Also sawed out and slightly angled the rudders
![Album image #5 Album image #5](/albums/img/4/0/5/889405-48987-55-720.jpg)
made a gun from a sprue disc and stretched cotton bud
![Album image #6 Album image #6](/albums/img/4/0/6/889406-48987-47-720.jpg)
the infamous HB Mad Riveter was unleashed on this kit as well. My solution was a massage with acrylic putty. Through drying shrinkage it still leaves some shallow rivets which are more suitable than the bullet holes before that. The rivets on the lids were closed with proper putty and sanded flush, I will add new rivets along the edge there
![Album image #7 Album image #7](/albums/img/4/0/7/889407-48987-81-720.jpg)
No chafflare buckets in the kit so I decided to scratch the actual dual buckets. This is just the first step, next will be putty and sand. My original plan to drill the holes with the PE template from the hasegawa kit failed because I am too clumsy and my tools suck. My new plan is to just paint them with the PE pieces as masks. Still better than nothing.
![Album image #8 Album image #8](/albums/img/4/0/8/889408-48987-28-720.jpg)
Kit actually offers interior on the rear end, sad they messed it up with giant pin constructions...
![Album image #9 Album image #9](/albums/img/4/0/9/889409-48987-99-720.jpg)
![Album image #10 Album image #10](/albums/img/4/2/5/889425-48987-11-720.jpg)
cockpit in its place, also I added the bulges on the canopy frame
![Album image #11 Album image #11](/albums/img/6/6/2/893662-48987-10-720.jpg)
had to get rid of some plastic to marry the two halves
![Album image #12 Album image #12](/albums/img/6/6/3/893663-48987-34-720.jpg)
Otherwise fit was ok, especially the side fuselage pieces were not a problem (as on some other hornets)
![Album image #13 Album image #13](/albums/img/6/6/4/893664-48987-88-720.jpg)
thats something eeh ... special...fixed that on the right
![Album image #14 Album image #14](/albums/img/6/6/5/893665-48987-23-720.jpg)
installed the bird slicers with sheet stripes on masking tape
![Album image #15 Album image #15](/albums/img/6/6/6/893666-48987-32-720.jpg)
finished the flare buckets. As you can see, some more putty work on the underside, as always with the hornets LEX. Also modified the centerline pylon from the straight to the angled shape
![Album image #16 Album image #16](/albums/img/6/7/1/893671-48987-61-720.jpg)
Some orange holo foil added to the Nite Hawk pod
![Album image #17 Album image #17](/albums/img/6/6/7/893667-48987-19-720.jpg)
applied some holo foil to the HUD, quite a nice highlight on a plain gray plane
I also exchanged the kits seat to the more recent SJU-17 + added the MFD cameras left+right to the pilot, both stolen from revell super hornets
I also exchanged the kits seat to the more recent SJU-17 + added the MFD cameras left+right to the pilot, both stolen from revell super hornets
![Album image #18 Album image #18](/albums/img/3/5/5/896355-48987-94-720.jpg)
lots of panels to shade
![Album image #19 Album image #19](/albums/img/3/5/6/896356-48987-41-720.jpg)
![Album image #20 Album image #20](/albums/img/3/5/7/896357-48987-25-720.jpg)
First rough paint layer, I usually go panel by panel, leaving a dark edge arround the panel lines which will get treated seperately. This way I get an irregegular look over the whole plane and dont accidentally kill the preshade.
Blue: This panel line along the spine was tragically forgotten by HB, rescribed it
Red: Deepened this one significantly as it is a very prominent gap on the original
Blue: This panel line along the spine was tragically forgotten by HB, rescribed it
Red: Deepened this one significantly as it is a very prominent gap on the original
![Album image #21 Album image #21](/albums/img/3/5/8/896358-48987-72-720.jpg)
Second coat is on. I also added some resprayed areas using the "fresh" dark ghost gray from vallejo, the rest is the bleached out looking DGG as it comes out of the AK RC 251
![Album image #22 Album image #22](/albums/img/5/6/5/896565-48987-53-720.jpg)
masking the layout, the ring is cut from the dropper of an empty vallejo bottle and glued with PVA
![Album image #23 Album image #23](/albums/img/5/6/6/896566-48987-62-720.jpg)
usual method of dabbing cheap thick acrylic paint. In hindsight I should have done this less thick in the beginning as it tends to push into the crevices and under the tape and you have to clean up. Which is not that hard as the paint is easy to remove
![Album image #24 Album image #24](/albums/img/5/6/7/896567-48987-48-720.jpg)
Voila - painted with light ghost gray, which will get wheathered down. Only the ring got a bit too fat maybe, but ok
![Album image #25 Album image #25](/albums/img/5/6/8/896568-48987-19-720.jpg)
looks nice+rough
![Album image #26 Album image #26](/albums/img/8/5/1/900851-48987-61-720.jpg)
CM stores loaded - used PE pieces from hasegawas hornet as paint mask
![Album image #27 Album image #27](/albums/img/8/5/2/900852-48987-85-720.jpg)
decals check! Very good quality by twobobs
![Album image #28 Album image #28](/albums/img/2/1/7/901217-48987-65-720.jpg)
GPS Dome added to the spine
![Album image #29 Album image #29](/albums/img/2/1/8/901218-48987-34-720.jpg)
Sadly the intakes end after a few cm and you look at the inner gear bay structure...I am not one of the people who aim their torchlights down the intakes - but that needed fixing. So I put a background with a dark grey gradient airbrushed on.
![Album image #30 Album image #30](/albums/img/2/1/9/901219-48987-17-720.jpg)
thats how the hatches look after new riveting, and a wash
![Album image #31 Album image #31](/albums/img/2/2/0/901220-48987-40-720.jpg)
weathering of the top side done, but the cell phone cam is still loving the blue too much in daylight...
btw, HB forgot the small but important exhaust holes between the fins, watch out for that if you build it
btw, HB forgot the small but important exhaust holes between the fins, watch out for that if you build it
![Album image #32 Album image #32](/albums/img/2/2/1/901221-48987-98-720.jpg)
under artificial light it looks closer to reality with the camera considering the blue-amount
![Album image #33 Album image #33](/albums/img/2/0/8/904208-48987-11-720.jpg)
on its legs now
![Album image #34 Album image #34](/albums/img/2/0/9/904209-48987-85-720.jpg)
Sorry friends of the soap, but thats how I like my models 😉
![Album image #35 Album image #35](/albums/img/2/1/0/904210-48987-23-720.jpg)
the kit offers seperate slats + flaps but to make them extended you have to cut the hinges and re-attach
Commentaires
19 7 December 2020, 14:21
![](/profiles/img/48987-587-s.jpg)
Welcome Roland+Maciej! I made some progress in the meantime and finished the major build stages. I really love the elegant shape of the D-Hornets, can't wait to start painting her 🙂
13 December 2020, 22:09
![](/profiles/img/48987-587-s.jpg)
Thanks Roland, no, its not a shake+bake by any means, still nothing major to get mad at. Dryfitting is really advisable though😉
13 December 2020, 22:10
![](/profiles/img/69105-967-s.jpg)
Looking good! Also, love the D model, wonder how this kit compares to kinetic's offering
14 December 2020, 14:51
![](/profiles/img/12696-s.png)
Following! 🙂 thanks for the captions btw for i do have the single seater and knowing before what to expect will surely help a lot.
14 December 2020, 20:57
![](/profiles/img/48987-587-s.jpg)
First paint layers are down! I plan to keep a bit more tidy since it its ground based, but who knows where the road will take me😉
@Peter: Thank you! I ask myself the same question, the kinetic is still on the wishlist. What I can say is that it comes with many more options for the different airframe updates. This one is based on an early D.
@ James&Jos: Great to have you on board! 👍
@Murad: Welcome! Great if I can be of help, I'll try to point out the major issues
18 December 2020, 18:54
![](/profiles/img/35457-839-s.jpg)
Great progress Daniel, next project of my shall also become a Hornet...👍
19 December 2020, 20:06
![](/profiles/img/35457-839-s.jpg)
Get your point about which kit Daniel..already ordered a lot of resin stuff for the HB kit...😄
22 December 2020, 18:32
![](/profiles/img/35457-839-s.jpg)
Gonna plan a next HB F-18 project myself...studied your pics very closely, good tips Daniel especially to fill those damn huge rivets on the wings...WTF!
From the low countries, merry Christmas my friend!
25 December 2020, 12:11
![](/profiles/img/48987-587-s.jpg)
Thx!
@jos: added a closer look at the outcome of the rivet treatment on pic 30, quite satisfied with it
@roland: Bavarian kingdom? 😄 jia griaß di! I am now living in the swabian empire...
(but I am not swabian by birth, praise the lord 😄)
26 December 2020, 18:02
![](/profiles/img/35457-839-s.jpg)
Thx Daniel, I've already made a riveting plan thanks to your pics...your riveting came out very nicely on those inspection hatches, much more real...👍
26 December 2020, 18:11
![](/profiles/img/48987-587-s.jpg)
not much work this time of year+no "visit the whole family" tour = time for the important things in life 😄
(ok -I admit I really miss the family tour...)
30 December 2020, 20:34
![](/profiles/img/23842-243-s.jpg)
Wow, I almost missed this one. You are working wonders on this kit Daniel. Can't wait to see the finish.
31 December 2020, 03:32
![](/profiles/img/23842-243-s.jpg)
I just went back and read how you approached the paint work on this build. I'm going to have to try that out 🙂
31 December 2020, 16:12
![](/profiles/img/48987-587-s.jpg)
@ Nathan: I found concentrating on individual panels really being a big step in bringing me closer to the desired result, previously I painted big surface patterns as you would on a car and it really makes a difference in the end
@Slavo: thanks+amen - a beautiful mess is what we aim for 😄
@ all: Thank you for joining in, a happy new year to everyone as well!
See pics here: Viking Night Attack - Armed+Ready | Album by halohead (1:48)
3 January 2021, 13:27
Album info
This HB Kit looks like a hornet, but only from afar - a lot of work needed to get it in the right direction...