Hírfolyam
Aycee
új fotóalbumot adott hozzá.
új fotóalbumot adott hozzá.
18 September, 11:26
Stephen Lesley
új fotóalbumot adott hozzá.
új fotóalbumot adott hozzá.
24 képek
Tamiya Panther G late.Új: 18 September, 11:30 1:35
This is the tank I will be modelling. Early 1945 in Hungary.
Projekt: Tamiya Panther G (Late)
22 14 July 2023, 07:28
Stephen Lesley
Thank you Spanjaard and Villiers. Yes, a classic indeed, but as always with a few issues. As the saying goes "some days a diamond , some days a stone". Today was a stone...
Thank you Spanjaard and Villiers. Yes, a classic indeed, but as always with a few issues. As the saying goes "some days a diamond , some days a stone". Today was a stone...
20 July 2023, 09:25
Spanjaard
classic indeed, i have a very similar project inventory, so really interested in the issues you may find 😉
classic indeed, i have a very similar project inventory, so really interested in the issues you may find 😉
20 July 2023, 11:26
Stephen Lesley
The issues I found were with the lower hull and the rear panel. These have to be carefully lined up or it can affect the fit with the upper hull. The turret was slightly warped which affected the fit with the turret ring and how it sits on top of the hull. The most annoying issue so far is the fitting of the side skirt brackets to the frame and the frame to the hull. The sprue gates for the brackets are on the mating surface so if you don't file them perfectly flat, they are out of line. And in a complete brain fart on behalf of Tamiya they designed the kit in such a way that if you attach all the tool racks etc on the the right hand side of the hull using the mounting holes, it prevents you attaching the side skirt frame properly, because the tools end up too low on the hull side. In the end I had to break off the jack block and some of the tool clamps to make the frame fit on the side. Not happy!
The issues I found were with the lower hull and the rear panel. These have to be carefully lined up or it can affect the fit with the upper hull. The turret was slightly warped which affected the fit with the turret ring and how it sits on top of the hull. The most annoying issue so far is the fitting of the side skirt brackets to the frame and the frame to the hull. The sprue gates for the brackets are on the mating surface so if you don't file them perfectly flat, they are out of line. And in a complete brain fart on behalf of Tamiya they designed the kit in such a way that if you attach all the tool racks etc on the the right hand side of the hull using the mounting holes, it prevents you attaching the side skirt frame properly, because the tools end up too low on the hull side. In the end I had to break off the jack block and some of the tool clamps to make the frame fit on the side. Not happy!
20 July 2023, 12:13
Stephen Fenech
megszerezte ezt
megszerezte ezt
SIAI Marchetti SF-260 Flying with Air Forces Around the World
Aircraft in Detail No. 016
Robert Pied, Nicolas Deboeck
2021 18 September, 11:29
PGLSMATES
megszerezte ezt
megszerezte ezt
M1 Assault Breacher Vehicle (ABV) M1150 with Mine Plow
Rye Field Model (RFM) 1:35
RM-5011 2016 Új alkatrészek 18 September, 11:27
Goldman
új fotóalbumot adott hozzá.
új fotóalbumot adott hozzá.
12 képek
Freightliner FLD WIP1:24
I built the base chassis 25 years ago. Checking it I don't see any major alignment issues. Had to clean many moulding li...
Projekt: Freightliner FLD 120
7 1 August, 04:59
Martin Oostrom
Beware. Zero paints are VERY hot and can affect your plastic, even through a primer. Use a 2k primer, or spray many very thin layers of paint with ample drying time in between.
Beware. Zero paints are VERY hot and can affect your plastic, even through a primer. Use a 2k primer, or spray many very thin layers of paint with ample drying time in between.
18 September, 08:55
Goldman
Thank Martin. Yes, I know. I have used Zero Paints before. Using Mr. Priming Surfacer as a primer which is pretty robust and (at least trying) to spray the Zero paint in thin layers I did manage to have only very little crazing. Actually the Zero paint dry quite fast - I only wait several minutes between (thin) layers.
Thank Martin. Yes, I know. I have used Zero Paints before. Using Mr. Priming Surfacer as a primer which is pretty robust and (at least trying) to spray the Zero paint in thin layers I did manage to have only very little crazing. Actually the Zero paint dry quite fast - I only wait several minutes between (thin) layers.
18 September, 11:23
Jan
akarja ezt
akarja ezt
Jedi Starfighter with hyperdrive ring Kuat Systems Engineering Light Interceptor
Fine Molds 1:72
SW-3 2002 Új eszköz 18 September, 11:23
Markus Helmers
új fotóalbumot adott hozzá.
új fotóalbumot adott hozzá.
20 képek
Yoda 1:4 Screamin' Vinyl KitÚj: 18 September, 11:13 1:4
Calling this one done for now. Probably will get back to it if and when my skills have evolved.
Projekt: Yoda on Dagobah
27 24 July, 11:02
Robin (WhiteGlint)
Oh this looks great Markus! 👀 👍
I am also having trouble with AK's Still Water. Didn't quite figure out yet how to use it well and I keep getting air bubbles.
Oh this looks great Markus! 👀 👍
I am also having trouble with AK's Still Water. Didn't quite figure out yet how to use it well and I keep getting air bubbles.
14 August, 06:55
Soeren R.
megrendeltnek jelölte ezt
megrendeltnek jelölte ezt
F-14A Tomcat air intakes (Tamiya) (3D Printed)
ResKit 1:48
RSU48-0378 18 September, 11:12
/hu/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=hu
35
35
/hu/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo