Hírfolyam

Luis
+ Eduard 1995 FE flaps.

Oleg Smilyk
Hey, Oleg, a very rare object in excellent execution!Excellent attention to detail!

Finn
Well done indeed!

Oleg Bogolei
Thanks! This model is very easy to build)

Ben M
Were you happy with the quality of the 3d printed kit?

Oleg Bogolei
yes. Very good quality. Easy to build. And ss-model makes sepparate tracks and weels which is good for me)

Neuling
Top small scale build!

Ben M
Thanks, Oleg. I may give one of their kits a try sometime then. They have some interesting subjects.

Mr D
Hi Duster 👋😃
Looking good, lve never built a Haseagawa....how have you found it..??
Good luck with next steps 👍👍

Guy Rump
Looking good, following. 👍

Duster_d
@Mr D,Hi, I like this build of this kit. The casting is thin and neat, although there are some minor flaws. The connection between the parts is good and the edges of the wings are sharp and thin. The decal has a thick layer of varnish. The plastic is typical of this company's kits (I have looked at other Hasegawa kits in my stash) some details is translucent in places, but durable.

@Guy, Thanks, I'll try hard 🙂

Duster_d
I applied this primer three times and washed it off three times. "Orange peel" every time. And I diluted it and tried undiluted, degreased the model with alcohol - the result is the same. That's enough trying for today.

Ben M
After my experience with my MiG-15, I'm done with Vallejo primer.

Duster_d
@Ben M, yes, I remember your MiG-15. I have never had problems with Vallejo primers before. They suddenly started back on my Super Etendard, but I thought it was an isolated incident. I have already sinned against isopropyl alcohol and the composition of water, I do not understand why these problems began.

Duster_d
I still didn't calm down. 🙂 Through experiments, it was possible to achieve a more or less normal application of the primer. The best results are achieved on a fat-free surface, without dilution, and at a minimum pressure of 0.8-1 bar.

[img1]

Nicolas
Following.

Duster_d
Do you guys think I should "strip" the paint even more? I liked working with Vallejo's chipping liquid 🙂

Ben M
I've seen all kinds of chipping on WWII Japanese aircraft. I'd say you can't go wrong.

Sy Bar
Was going to do the Battle of Britain version of this kit but I'm temped to have a go at some winter white wash and the wasp is cooler than the shark mouth 😎

Nicolas
Following

István Szücs
I also have Bf-110 from the Airfix, I will build an Italian night fighter. The sprues are the same, so I'm watching!

Sy Bar
Cheers guys.
I'm have a go at riveting, but going freehand as at this scale using tape was taking so long. I also not sure how much they will stand out on finish kit, but with the wonky line in parts they will probably bee seen from mars 🤣

Mark Sherwood
Looking good so far, like the underside. 🥸👍

Sy Bar
Cheers #Mark

Skyhiker
Sy, how was the fit on this kit?

Guy Rump
Looking good, following. 👍

Sy Bar
Cheers #Guy 👍
#Skyhiker I found the fit to be good, I had a very slight gap at the front but think that was as much to do with me and the fitting of the pit (not the clearest instructions there). Every thing else was fine and the canopy was a good fit, I did change order of build slightly with the tail section I glued the rear piece to the body first then added the tail (after I'd added the stabilisers/rudders) this made more sense than the instructions 😁

Sy Bar
Only issue I have with this kit are the decals. While they look great and are in perfect register, they have a large amount of film edging and are both thick and delicate at the same time🤪
Having a hard time getting them to settle into the panel lines etc. I usually just need to use micro sol but even ultimate extra strong is not have much effect. Going to have to wait till I get some Tamiya fixer, strong and extra strong hopefully one of these will help 🤞

Mr D
You should be ok with the medium one with Airfix decals,
I like a mix of Water in with the markfix...seems to keep the decal floating longer.
I did the teeth on my p40 this way.
If they started getting bit sicky...l would add bit more water....keep it floating.
Wouldn't like to do shark teeth with HB decals 🤔🤣.... The lightning ⚡ strike on my mig-15 just fell apart with hardly any working.
Good luck with it ..look forward to seeing 😃👍👍

Dave Flitton
Looking good!

Sy Bar
Cheers for advice #Mr D. Afraid this set of decals were unaffected by all solutions but the mark fit super strong did have some effect. To make head way I found I needed to add the solution then after a few seconds apply hot air from a hairdryer to 'shrink wrap' the decal. These have to be the worst decals I've come across..
I recommend anyone doing this kit to source a set of decals rather than use those provided, they are not for beginners that's for sure. I hope the carrier film will disappear under a gloss coat but I didn't want to risk it so I've only applied the larger decals the smaller ones while add great detail if cartograf here they are 90% carrier film.

Skyhiker
Why don't you just cut the carrier film away with a knife before applying them?

Mr D
Hi Sy
That's ok .... I think the result will be fine after a clear coat, you come out of it without wrinkles, bubbles or tear's so it's a win, very smart n be sorted under a clear.👌👍👍

Sy Bar
Cheers #Mr D
#Skyhiker that's idea but life's too short for the amount there is, the size of the decal that's left will look like small black dots everywhere (especially the fuselage rib numbers 🤪); would be ok in 48 but too much in 72. Also I'm probably going to much it all up when I apply the winter white wash 😆

Rui S
That's Looking Great 👍