Hírfolyam
Jeroen
akarja ezt
akarja ezt
Versuchsflakwagen 8.8 cm Flak (41/37) auf Sonderfahrgestell Pz.Sfl. IVc tracks
Friulmodel 1:35
ATL-111 2016 Új eszköz Több téma (2)18 October, 21:30
penubly
akarja ezt
akarja ezt
SAS& LRDG COMBO KIT - Chevrolet WA & Jeep
Dogfight Workshop 1:48
48A20 2024 Új alkatrészek Több téma (2)18 October, 21:24
Qwertzel
új fotóalbumot adott hozzá.
új fotóalbumot adott hozzá.
13 képek
Revell Rosenbauer GFLF Simba 8x8Új: 18 October, 11:31 1:24
Before and after
Projekt: Revell Rosenbauer GFLF Simba 8x8
7 7 October, 13:54
Martin Oostrom
I have been drooling over this kit since it was new, so definitely following
I have been drooling over this kit since it was new, so definitely following
7 October, 14:21
Bozzer
Yeah, I agree with Martin. This has always been a kit, I wanted to get my hands on. I actually saw the built model, at Bolton IPMS in January. Those tyres are amazing and the vehicle itself, looked almost space-like.
Yeah, I agree with Martin. This has always been a kit, I wanted to get my hands on. I actually saw the built model, at Bolton IPMS in January. Those tyres are amazing and the vehicle itself, looked almost space-like.
13 October, 06:42
Petr Kreps
új fotóalbumot adott hozzá.
új fotóalbumot adott hozzá.
13 képek
ERA-3B "Whale" SkywarriorÚj: 18 October, 21:19 1:48
I’ve started with front wheel bay, I have used some Eduard’s PEs and some wires.
Projekt: ERA-3B “Whale” Skywarrior
Scratchbuilt
6 8 October, 16:31
H Kato
új fotóalbumot adott hozzá.
új fotóalbumot adott hozzá.
3 18 October, 18:54
Landlubber Mike
Wow, nicely done! Do you mind me asking what paints/colors you used for the finish and roof? Looks great!
Also, how did you do the license plate? Looks very clean.
Thanks!
Wow, nicely done! Do you mind me asking what paints/colors you used for the finish and roof? Looks great!
Also, how did you do the license plate? Looks very clean.
Thanks!
18 October, 20:33
H Kato
Thank you for your comment! The body is GSI Creos #8 Silver sprayed with #101 Smoke Gray. The roof is Gaianotes CB-25 Desert Orange 33825.
The license plate was made by cutting a piece of Tamiya plastic sheet to size and sticking the included decal on it.
Thank you for your comment! The body is GSI Creos #8 Silver sprayed with #101 Smoke Gray. The roof is Gaianotes CB-25 Desert Orange 33825.
The license plate was made by cutting a piece of Tamiya plastic sheet to size and sticking the included decal on it.
18 October, 21:17
NLAWScametovisit
új fotóalbumot adott hozzá.
új fotóalbumot adott hozzá.
28 16 July, 13:41
NLAWScametovisit
Sorry about the slow rate of updates everyone. I hurt my back at the gym so I'm having to avoid being hunched over at the modeling bench this week.
Sorry about the slow rate of updates everyone. I hurt my back at the gym so I'm having to avoid being hunched over at the modeling bench this week.
19 July, 14:02
NLAWScametovisit
OK! Back at it with the interior. This kit is definitely a jump in difficulty from the last one. PE is definitely difficult, and if you're doing this kit, make sure you frequently fit check the flight seats and how they'll mount to the bulkheads!
OK! Back at it with the interior. This kit is definitely a jump in difficulty from the last one. PE is definitely difficult, and if you're doing this kit, make sure you frequently fit check the flight seats and how they'll mount to the bulkheads!
7 August, 15:57
NLAWScametovisit
AAAAAND I hurt my back again pushing too hard at physical therapy. :/ more delays
AAAAAND I hurt my back again pushing too hard at physical therapy. :/ more delays
22 August, 19:14
NLAWScametovisit
the detailing on this kit is really lovely, but the fitting of the parts is really bad. And advice on fixing the massive panel gaps in pic 43 to 47 is appreciated.
the detailing on this kit is really lovely, but the fitting of the parts is really bad. And advice on fixing the massive panel gaps in pic 43 to 47 is appreciated.
3 September, 22:27
Moritz
Is the top portion already glued on? If not, try adding some bracing with some cut sprues to force the sides apart. Right about where the kink/end of the doghouse is.
Is the aft bulkhead of the crew cabin causing the problem? If that is glued to both sides, forcing the sides apart may not work.
Is the top portion already glued on? If not, try adding some bracing with some cut sprues to force the sides apart. Right about where the kink/end of the doghouse is.
Is the aft bulkhead of the crew cabin causing the problem? If that is glued to both sides, forcing the sides apart may not work.
5 September, 04:03
NLAWScametovisit
Very good advice. Had to pry it apart but addint braces definitely helped!
Very good advice. Had to pry it apart but addint braces definitely helped!
5 September, 18:58
Anatolii Smyshliaiev
If still relevant.
Pic 43-45. Before gluing the fuselage roof to the lower part, I glued 2 spacers from sprue scraps between the walls.
Pic 46 and 47.
I simply cut off the inner side of the hood wall, leaving the outer side untouched, achieving a tight fit along the outer surface. And I puttyed a little bit on the front of the hood.
If still relevant.
Pic 43-45. Before gluing the fuselage roof to the lower part, I glued 2 spacers from sprue scraps between the walls.
Pic 46 and 47.
I simply cut off the inner side of the hood wall, leaving the outer side untouched, achieving a tight fit along the outer surface. And I puttyed a little bit on the front of the hood.
24 September, 08:14
Augie 2025
akarja ezt
akarja ezt
60‘~70’s Saigon Shuttle Motor-Tricycle Depot and a take break drive [2 kits In 1 box]
Gecko Models 1:35
35GM0113 2024 Új alkatrészek 18 October, 21:16
/hu/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=hu
35
35
/hu/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo