MiG-21PF (76)

1
January 5, 2024
Stripes of PLA paper were added just for better fit between halves of wings.
2
January 5, 2024
Wings ready for assembly.
3
January 5, 2024
As usually in Eduard's MiGs a 0,2 mm PLA insert was needed to cancel a gap between fuselage and wings.
4
January 5, 2024
This aircraft may have been used with a Monsoon beam (?), which allowed two R-3S rockets to be carried under each wing. The parts needed for the Monsoon beam are on the "H" frame, but are described as "unused parts."
5
January 5, 2024
Pylon, Monsoon beam and two launcher beams together. Nice tower 🙂
6
January 5, 2024
Probably new modification of MiG - canards 😉. 0,1 mm PLA paper fills a gap between parts.
7
January 5, 2024
Cockpit almost ready 🙂
8
January 5, 2024
Current status of project (underwings pylons aren't glued jet).
9
January 5, 2024
Current status of project
10
January 6, 2024
Outlet nozzle cover sanded - a minute's work and the effect is much better than straight out of the box.
11
January 6, 2024
The exhaust nozzle cover and the previously modified nozzle tried on the model. Eduard won't make money on aftermarkets
12
January 6, 2024
The inlet cone traditionally does not fit in the ring. After a while, I thought about filing out the notches - bingo! Why didn't Eduard do it as standard?
13
January 6, 2024
Small parts glued up, light primer and "non-metallic" colors laid down. Now a quick masking and you can lay the primer for the metallics 🙂
14
January 6, 2024
Small parts glued up, light primer and "non-metallic" colors laid down. Now a quick masking and you can lay the primer for the metallics 🙂
15
January 8, 2024
Black primer (I had to change the background 😉 )
16
January 8, 2024
Metallics with some shadows
17
January 8, 2024
2K gloss varnish on metallics - changes "a bit" colours, but for decals it's a must 🙁
18
January 9, 2024
Sorry, but I have to remove 2K gloss varnish and paint model again or... find a new kit. The varnish layers are unacceptably thick and the model loses detail 🙁

Hozzászólások

14 5 January, 22:46

Sergej I
Following 👍

6 January, 00:32

Matthew A
🍿 🐻

6 January, 11:40

Nicolas
Me too.

6 January, 16:50

Tibor Szilvai
👍

8 January, 18:43

Sergej I
Hi Konrad. I would not go with this strong shadowy look...
Would paint metallic again and then seal it with Alclad ALC600 or Glänzer or AK Gauzy... all are basically the same water-based gloss. All also level perfectly if applied with a nice wide brush.

9 January, 17:36

Konrad
Unfortunately Sergej I have to agree with you. I put a 2K varnish on the model and... I lost a lot of sharpness of details 🙁 I'm looking for PF overtrees 🙁

9 January, 18:32

Cortex
make it an abandoned Mig-21, just add dust and streaks so that you don't have to trash the kit.

9 January, 23:50

Ludvík Kružík
OVERTREES MiG-21PF is available directly from the manufacturer:
eduard.com/cs/eduard..rchparam=mig-21%20pf

10 January, 00:27

Project info

MiG-21PF (76)

18 képek

1:72

Félrerakva

1:72 Stříbrné šípy (Mig-21PF/PFM) (Eduard 2134)

Összes album

Összes album megtekintése »