Maus 1/100
Hozzászólások
4 20 January 2019, 16:11
Zsolt Czegle
Thanks! Check the photo Nr.13. The Balkenkreuz is masked and airbrushed. There are no decals included.
Thanks! Check the photo Nr.13. The Balkenkreuz is masked and airbrushed. There are no decals included.
7 April 2020, 18:29
HSC1932
Thank you, I just got the same kit and I was worried. Would you mind uploading the image of all the paints you used to the photo album? The quality of the preview isn't good enough to make out exactly what you used.
Thank you, I just got the same kit and I was worried. Would you mind uploading the image of all the paints you used to the photo album? The quality of the preview isn't good enough to make out exactly what you used.
7 April 2020, 18:34
Zsolt Czegle
Used AK acrylics: Turret:AK127 and AK129 (Red Primer) , the Hull: AK 713, AK714 (both Dunkelgeb) and AK 715 (Resedagrün)
Used AK acrylics: Turret:AK127 and AK129 (Red Primer) , the Hull: AK 713, AK714 (both Dunkelgeb) and AK 715 (Resedagrün)
7 April 2020, 19:50
HSC1932
Thank you. I am building this kit myself, however there is a very small, but noticeable gap between the turret and the hull. If i press down on it very hard it seals, but it'll oftentimes "pop up" again. How do I close this gap without removing my ability of being able to turn the turret?
Thank you. I am building this kit myself, however there is a very small, but noticeable gap between the turret and the hull. If i press down on it very hard it seals, but it'll oftentimes "pop up" again. How do I close this gap without removing my ability of being able to turn the turret?
17 June 2020, 00:29
Bart Goesaert
making enough room for it to sit flush? (scraping paint away on contact surfaces. Always better to check this before painting. When you turn the turret a few times, do you see specific paintdamage in the area? This can be usefull to determine what to do... or where to remove paint
making enough room for it to sit flush? (scraping paint away on contact surfaces. Always better to check this before painting. When you turn the turret a few times, do you see specific paintdamage in the area? This can be usefull to determine what to do... or where to remove paint
18 June 2020, 13:19
Zsolt Czegle
Thank you Spanjaard!
OttovonLindberg: Bart has right! Make the hole on the turret a little bit bigger. So it won't pop up anymore.
Thank you Spanjaard!
OttovonLindberg: Bart has right! Make the hole on the turret a little bit bigger. So it won't pop up anymore.
18 June 2020, 15:54
HSC1932
Hi Bart, I have not yet painted the model.
Hi Zsolt, thanks, I will try that. I sanded down the turret bottom some, and it didn't seem to help
Hi Bart, I have not yet painted the model.
Hi Zsolt, thanks, I will try that. I sanded down the turret bottom some, and it didn't seem to help
19 June 2020, 05:57
Bart Goesaert
Did you sand the vertical surfaces? On the bare plastic you dan also see the friction marks.
Did you sand the vertical surfaces? On the bare plastic you dan also see the friction marks.
19 June 2020, 13:06
HSC1932
I have sanded down the turret bottom with a 160 grit sanding file. Looking at the upper hull, I do see two rings where it seems the turret cut into the plastic (the friction marks you're referring to).
I have sanded down the turret bottom with a 160 grit sanding file. Looking at the upper hull, I do see two rings where it seems the turret cut into the plastic (the friction marks you're referring to).
19 June 2020, 16:35
Zsolt Czegle
OttovonLindberg upload photos about your build into your project's album. So we can see your photos and so we coud help you! 🙂
OttovonLindberg upload photos about your build into your project's album. So we can see your photos and so we coud help you! 🙂
19 June 2020, 21:07