De Havilland DH.88 Comet G-ACSS - completed

1
September 27, 2020
Each nacelle has cooling gills on both sides. With a small round milling head I thinned carefully the material from inner side.
2
October 1, 2020
Seams cleaned, separation lines restored. As usual I used CA and plastic as filler.
3
October 1, 2020
4
October 1, 2020
Etched rear part for the inner side of the flap area reinforced with plastic stripes.
5
October 1, 2020
6
October 1, 2020
Rear parts of the nacelles: left and right reversed🙁🙁🙁 arghhhh!
7
October 1, 2020
Sometimes the most radical way is the best way: nacelles ripped off.
8
October 3, 2020
On course again.
9
October 3, 2020
10
October 3, 2020
Next step: engine puzzle.
11
October 4, 2020
12
October 5, 2020
13
October 5, 2020
14
October 5, 2020
15
October 5, 2020
16
October 5, 2020
Right: behind the cooling gills white paper is well visible as airbrush-dust protection (engine should remain black an not will be red).
17
October 7, 2020
18
October 7, 2020
19
October 7, 2020
20
October 7, 2020
21
October 7, 2020
22
October 9, 2020
23
October 9, 2020
24
October 9, 2020
25
October 10, 2020
A dish of aluminum sheet as reflector
26
October 10, 2020
Shoulder harnes added.
27
October 10, 2020
I don’t like photo etched flaps because they are to fragile and it’s difficult to fit them on the rest. Because of that I invested one half of hour and made them of plastic.
28
October 10, 2020
Pudding plane - Time!🙂
29
October 15, 2020
30
October 15, 2020
31
October 15, 2020
32
October 17, 2020
33
October 19, 2020
34
October 19, 2020
35
October 19, 2020
Landing gear completed minus red covers and air valves
36
October 19, 2020
37
October 20, 2020
Tires and air valves in place = landing gear completed.
38
October 20, 2020
Surprisingly the landing gears stays in place without glue🙂
39
October 21, 2020
40
October 21, 2020
41
October 21, 2020
42
October 21, 2020
43
October 21, 2020
44
October 21, 2020
45
October 21, 2020
46
October 21, 2020
47
October 21, 2020
48
October 21, 2020
49
October 21, 2020
50
October 21, 2020
51
October 21, 2020
52
October 21, 2020

Hozzászólások

43 27 September 2020, 15:42

bughunter
A new project?! This plane is a beauty 👍 Watching!

29 September 2020, 17:25

Bernhard Schrock
A small progress in WIP building: the wing is completed and both rear parts of the nacelle are in place. But I made a mistake and reversed the parts. Now the are in wrong angle. I hope that my best friend (CA glue) will help me to set things right by gluing the forward parts under "tension".

1 October 2020, 04:22

Hanno Kleinecke
Veery reassuring to see that happening to even someone super experienced like you...... ( reversed sides)
Thats my typical way of doing and then discovering the instructions afterwards 🙂
Doubtlessly, this will be no problem for you to fix.
Can't wait to see that beautiful red paint coming into view !

1 October 2020, 05:22

Spanjaard
a beautiful plane indeed. looking forward to what you do with it 🙂

1 October 2020, 08:05

Alec K
Following. Keeping my fingers crossed for those engine nacelles 👍

1 October 2020, 12:35

Bernhard Schrock
Thank you Hanno, Spanjaard and Alec for your supporting words. For about one hour I tried, bent, glued and realized that it's impossible for me to fix this mistake in a way that satisfies me. So I ripped of the parts again fortunately without damage. This is a big advantage of CA in comparison with standard plastic glue. More luck next time! 🙂

1 October 2020, 17:28

Christoph Kunz
Count me in

1 October 2020, 18:51

Alec K
Eureka 🙂 👍

2 October 2020, 12:19

Zbynek Honzik
Watching!

2 October 2020, 15:48

Treehugger
Ripping the glued on parts off, I've done that a couple of times. 😄

3 October 2020, 12:15

David Funke
Oh, I´ll take a seat....

4 October 2020, 19:15

bughunter
Your instrument panel looks better than a Löök😉
Regarding the fit: You are doing the test build, prior starting production? Or this kit is only for collectors but not intended to be build.

5 October 2020, 16:49

Bernhard Schrock
Thx bughunter. I'm curious when I can see a second Comet build coming ... indeed it is imo more a collector kit.

5 October 2020, 18:05

Erik Off
Och, ich wollte sie schon bauen - irgendwann.😉
Dein BB wird dafür wieder eine große Hilfe sein und der Link ist schon abgespeichert.😉

6 October 2020, 05:43

Slavo Hazucha
Somewhat behind the first-row spectators, but definitely joining this! Just coming back from a project with a lot of red, looking forward to this 👍 What are you going to use for the perfect "Rosso corsa" effect? I guess this is where old-school gloss enamel color would get a stage to shine... 🙂

6 October 2020, 09:26

Bernhard Schrock
Indeed it is a big challenge: entire plane in red. I plan to use my usual technique. First I'm going to airbrush the canopy area dark grey and then a base of pale rose (mix of light grey and red). Based on my experience 100% gloss for a model is too much gloss and makes it look like a toy. Because of that I will mix H19 (gloss red) with H174 (satin red).

6 October 2020, 12:47

Treehugger
Does that mean you don't use a gloss coat over the entire model, nor any varnish, or at least not for this project?

I have had imo good success with applying a gloss coat (or two), and then in an instant turning the model from looking like a toy, to a more realistic looking surface that has shine and reflection to it, being satin. Having said that, I have had trouble applying the satin varnish in a uniform way, perhaps because my lighting by my desk isn't the best. I always need direct light to be able to see where I spray the gloss coat, or the varnish, or I don't even see what I am doing when airbrushing that stuff. I have lately been using goggles for my eyes and a dust mask, as I like keeping my face close to the model when airbrushing. :| Heh, on top of that I like having wireless headphones, listening to modeling podcasts on youtube.

6 October 2020, 13:07

Bernhard Schrock
Treehugger: this is correct. As usual (in 9 of 10 cases) I use no gloss varnish before applying decals and no varnish after applying decals. The different shininess of the surface is a important part of my "finish philosophy". At last I used semi gloss varnish for my Hughes racer because I had the correct blue shade only as semi mat paint.

7 October 2020, 06:42

Slavo Hazucha
Cool progress, especially like the balance rods! 👍

Where you take all that solid technical data for all those updates & modifications - internet, or do you have a grand library of source materials?

9 October 2020, 15:23

Bernhard Schrock
Thank you Slavo. I decided to build the red plane because it's preserved in excellent condition in shutterwotth collection. As usual I looked first on Wikipedia (commons) for original pictures and found a lot of information.

Further I discovered a very interessant thread:
ww2aircraft.net/foru..villand-comet.51473/

9 October 2020, 16:02

Bernhard Schrock
To minimize dust particles during airbrushing red I decided to use semi matte paint. Yesterday i completed the finish via airbrushing a clear coat. That worked and I'm very satisfied with the result. This morning I took off the masks: I used the kit's exactly precut masks. Warning: some left a little residue on the clear part. Possibly you can't leave them on for too long.

17 October 2020, 08:03

bughunter
What a beautiful and elegant plane 👍 Great work as usual!

17 October 2020, 17:29

Daniel
I can only agree!

17 October 2020, 17:39

Christoph Kunz
Simply WOW

17 October 2020, 18:20

KlausH
What a beauty! Great work Bernhard! Your hints will be very useful for my Comet. Thanks much!

17 October 2020, 18:21

Alec K
Outstanding work indeed 👍

18 October 2020, 12:58

Slavo Hazucha
I was too busy for a couple of days and boy what an escalation of progress!!! That´s a really great shade of red and the canopy - clarity, perfect fit, sharpness & thickness of lines... - looks just fabulous 👍

19 October 2020, 10:51

Hanno Kleinecke
Seehr schönes Rot und tolle „Beine" ! Das sieht nach ‚ner ziemlichen Fummelei aus, die kleinen Hilfsdrähtchen.......

19 October 2020, 11:47

Zsolt Czegle
Klasse Arbeit, wie immer! 👍

19 October 2020, 19:56

Clifford Keesler
Very nice so far.

19 October 2020, 22:48

Bernhard Schrock
Nice to hear that you like my "House"🙂. I almost finished today but I noticed that the propeller blades have some imperfections. Tomorrow I have to manage the last airbrush session.

20 October 2020, 19:20

Hanno Kleinecke
Fertig ! What a pretty little „Red Rooster" 😄 ! Beautiful work !

21 October 2020, 18:03

Lochsa River
What a beauty...Bernhard, you never disappoint.....so clean.

21 October 2020, 21:36

Clifford Keesler
Excellent job Bernhard.

21 October 2020, 22:19

Alec K
Looks funky with landing gear out 😄. But what an elegant aircraft 👍

22 October 2020, 00:21

Michael Hickey
Beautiful looking Comet Mate.👍👍👍

22 October 2020, 05:32

Christian Ristits
Sehr schöne Arbeit!

22 October 2020, 05:43

Erik Off
Wunderschön! Einfach wunderschön! 🙂

22 October 2020, 06:22

Felix Troschier
Excellent finish as usual

22 October 2020, 15:44

David Taylor
Very smart Bernhard lovely comet.

22 October 2020, 17:07

Christoph Kunz
Eine absolute Schönheit.

22 October 2020, 21:30

Slavo Hazucha
Looks fast even stationary! 🙂 Great job once again - museum piece 👍 Sooner or later I´ll have to try a racing/record machine, this is just too tempting for "watch only"...

29 October 2020, 19:19