HMS Bounty Build
![Album image #1 Album image #1](/albums/img/3/0/2/1426302-125926-28-720.jpg)
Gun ports cut out square instead of the circle on kit.
![Album image #2 Album image #2](/albums/img/3/0/1/1426301-125926-14-720.jpg)
Rails cut to depict hinged rising bar above steps. Still need to make the upright supports.
![Album image #3 Album image #3](/albums/img/3/1/1/1426311-125926-71-720.jpg)
Fore pin rails were originally moulded in the wrong position (red circles denote original moulding position) according to the Admiralty diagrams. Removed them leaving small bollards as per plans.
![Album image #4 Album image #4](/albums/img/3/0/4/1426304-125926-73-720.jpg)
Fore pin rail cleaned up and waiting to be glued into correct position.
![Album image #5 Album image #5](/albums/img/3/0/5/1426305-125926-68-720.jpg)
Port fore pin rail attached correctly.
![Album image #6 Album image #6](/albums/img/3/0/6/1426306-125926-91-720.jpg)
Hawse hole drilled through hull as no holes are on the kit. The deck needs to be dropped slightly at the bow when fitted.
![Album image #7 Album image #7](/albums/img/3/0/7/1426307-125926-31-720.jpg)
Testing hawse hole with hawse line.
![Album image #8 Album image #8](/albums/img/3/0/8/1426308-125926-32-720.jpg)
Holes for the anchors need plugging and filling.
![Album image #9 Album image #9](/albums/img/3/1/0/1426310-125926-89-720.jpg)
Holes plugged using the securing tabs from the anchors and Revell Plasto.
![Album image #10 Album image #10](/albums/img/3/0/9/1426309-125926-49-720.jpg)
Piece of 0.5mm styrene sheet glued on to inside of the hull to stop plug from falling through.
![Album image #11 Album image #11](/albums/img/2/9/7/1426297-125926-34-720.jpg)
Swivel gun stanchions removed and replaced with scratch built ones made from off cuts of sprue. They look more the ones in the plans. Only seven more to do.
![Album image #12 Album image #12](/albums/img/2/9/5/1426295-125926-22-720.jpg)
Pilot holes also drilled into stanchions for swivel guns.
![Album image #13 Album image #13](/albums/img/2/9/6/1426296-125926-57-720.jpg)
Lots of ejector pin marks on the deck filled with Plasto.
![Album image #14 Album image #14](/albums/img/2/9/8/1426298-125926-36-720.jpg)
Marks dry and sanded down smooth. Deck planks now need re-scribing.
![Album image #15 Album image #15](/albums/img/2/9/9/1426299-125926-17-720.jpg)
Windlass had a big sink hole in it. I could have left it as it will face the deck, but I knew it was there and it annoyed me.
![Album image #16 Album image #16](/albums/img/3/0/0/1426300-125926-82-720.jpg)
Drilling the holes in the windlass.
![Album image #17 Album image #17](/albums/img/9/9/1/1427991-125926-79-720.jpg)
I think I got a bit above myself with this one. I sanded the deck down as I felt the moulded planks were too small. I attempted to re-scribe the planks, but the deck was too flexible and I lost my lines. It looks awful, I know, but I don't think I can sand it down again and re do it.
Lesson for next time - make a jig or a support for the deck before attempting to do this job.
Lesson for next time - make a jig or a support for the deck before attempting to do this job.
![Album image #18 Album image #18](/albums/img/9/9/2/1427992-125926-87-720.jpg)
The top mast tops are cut and ready for shaping when the time comes to fit them.
![Album image #19 Album image #19](/albums/img/9/9/0/1427990-125926-14-720.jpg)
On a more positive note, I am happy with my rudder and tiller for the launch.
![Album image #20 Album image #20](/albums/img/9/9/3/1427993-125926-67-720.jpg)
Scrolls for the stern gallery
![Album image #21 Album image #21](/albums/img/9/9/4/1427994-125926-13-720.jpg)
After many attempts at this, I finally made a flag locker I am pleased with ...
![Album image #22 Album image #22](/albums/img/9/9/5/1427995-125926-25-720.jpg)
... and it fits. Just need to put the roof on it. I have already made a new, longer tiller to replace the silly little one in the kit.
![Album image #23 Album image #23](/albums/img/6/3/4/1430634-125926-80-720.jpg)
Mast top rails as they are not included in kit.
![Album image #24 Album image #24](/albums/img/6/3/7/1430637-125926-19-720.jpg)
Reference for rails
![Album image #25 Album image #25](/albums/img/6/3/5/1430635-125926-12-720.jpg)
Headrail modifications ...
![Album image #26 Album image #26](/albums/img/6/3/6/1430636-125926-55-720.jpg)
... and their reference.
![Album image #27 Album image #27](/albums/img/3/8/7/1439387-125926-91-720.jpg)
New stove chimney
![Album image #28 Album image #28](/albums/img/3/8/6/1439386-125926-18-720.jpg)
My scrach built chimney next to the original kit par
![Album image #29 Album image #29](/albums/img/3/8/9/1439389-125926-79-720.jpg)
The flag locker now has a roof
![Album image #30 Album image #30](/albums/img/3/9/0/1439390-125926-80-720.jpg)
Forward swivel gun stanchions in place
![Album image #31 Album image #31](/albums/img/3/9/1/1439391-125926-54-720.jpg)
Aft swivel gun stanchions in place
![Album image #32 Album image #32](/albums/img/3/9/2/1439392-125926-67-720.jpg)
Stern rigging beam fitted and hole for rigging drilled through
![Album image #33 Album image #33](/albums/img/3/9/3/1439393-125926-94-720.jpg)
My representation of a hinge for the gangway
![Album image #34 Album image #34](/albums/img/3/9/4/1439394-125926-95-720.jpg)
Dry fit of forward parts ...
![Album image #35 Album image #35](/albums/img/3/8/8/1439388-125926-64-720.jpg)
... and of aft parts
![Album image #36 Album image #36](/albums/img/3/1/8/1441318-125926-59-720.jpg)
Deck and hull primed with Stynylrez
![Album image #37 Album image #37](/albums/img/3/1/6/1441316-125926-12-720.jpg)
Priming begins on tops and stern gallery ...
![Album image #38 Album image #38](/albums/img/3/1/5/1441315-125926-65-720.jpg)
... and on the masts
![Album image #39 Album image #39](/albums/img/1/4/8/1447148-125926-36-720.jpg)
Hull painting commences and a dry fit
![Album image #40 Album image #40](/albums/img/3/1/4/1441314-125926-25-720.jpg)
Proposed colour scheme
![Album image #41 Album image #41](/albums/img/3/1/7/1441317-125926-73-720.jpg)
Painting co and dry fit
![Album image #42 Album image #42](/albums/img/1/4/6/1447146-125926-94-720.jpg)
Hull painting nearing completion (needs final touch ups) and another dry fit
![Album image #43 Album image #43](/albums/img/5/2/0/1449520-125926-53-720.jpg)
Making progress
![Album image #44 Album image #44](/albums/img/5/2/2/1449522-125926-11-720.jpg)
Ship's launch - oars tied down scratch built bowsprit, masts, and yards complete waiting for sail (?) and tie down
![Album image #45 Album image #45](/albums/img/5/2/3/1449523-125926-83-720.jpg)
Ships stern
![Album image #46 Album image #46](/albums/img/5/2/1/1449521-125926-16-720.jpg)
Scratch built ship's lanterns
![Album image #47 Album image #47](/albums/img/0/9/3/1451093-125926-42-720.jpg)
Lanterns painted - not sure if I like them
![Album image #48 Album image #48](/albums/img/0/9/5/1451095-125926-77-720.jpg)
Launch finished
![Album image #49 Album image #49](/albums/img/0/9/2/1451092-125926-46-720.jpg)
Hull and deck glued together - head rail fitted and most deck fittings
![Album image #50 Album image #50](/albums/img/0/9/4/1451094-125926-70-720.jpg)
![Album image #51 Album image #51](/albums/img/8/6/4/1466864-125926-31-720.jpg)
Bad photo, but this is where I am too at present. Hoping to get back to her in the next week or so.
Hozzászólások
11 13 March 2023, 17:47