Novità

Nathan Dempsey
There's another classic kit. Looking good so far. I'm following 👀

Clifford Keesler
Welcome Nathan.

Clifford Keesler
This one has the wing tips and vertical fin painted and is all primed.

Desert Marlin
Looking good!

Clifford Keesler
Thank you very much Desert Marlin.

Clifford Keesler
Decals finished and final clear coat applied. Next weathering. Pictures tomorrow hopefully.

Nathan Dempsey
The next project is up and running. This one will likely get a slow start as there's another hurricane headed my way…

Nathan Dempsey
Well we survived that darn hurricane and had power restored yesterday by some fine Canadian fellows from Nova Scotia. The project continues with some progress to the fuselage.

Clifford Keesler
Watching. Glad you weathered the hurricane ok. Did not know you were in Florida. I am a transplanted Florida guy. I am from Panama City. Was down there the end of August, first time I had been back since 2001. Hurricane Michael sure messed up the place, but they have rebuilt a lot. The house I lived in from 1995-2001 no longer exist, hurricane Michael leveled it.

Nathan Dempsey
We were part of mandatory evac. I sent the family away and stayed since my parents are next door in a 100 year old frame home. We were lucky and had minimal damage. We just lost large oaks and our entire cow field was a shallow lake. Power was out for a while but I'm used to living simple during such times. Yeah Michael was a monster.

The plastic in this kit is quite fragile. Getting parts off the tree cleanly is quite difficult. Very happy with the ResKit parts! They are very clean and easy to prepare.

Nathan Dempsey
More work today included adding etched parts to the rear fuselage and filling large holes intended for oversized antennas. Will be replacing all antennas with etched parts or thin plastic sheet.

Clifford Keesler
Looking good Nathan. Glad you only had minor damage, and all is well.

Clifford Keesler
I have 2 ESCI Mirage 2000's wonder if they are the same as the Heller kit?

Nathan Dempsey
Thank you sir! The Heller kit is the same as the Eduard kit. I believe the ESCI kit is now the Italeri kit.

Clifford Keesler
OK, thanks. Any way I have 2, hope they are good.

Nathan Dempsey
Work continues. Today I added some etched hydraulic lines to the rear landing gear. Preparation begins for the ResKit wheel set.

Clifford Keesler
Looking very nice sir.

Desert Marlin
Excellent work!!!

Dutch
Nathan, I love checking in from time to time, (super busy with Hurricane Helene and Milton recovery at the house and the rented house.). Anyway, glad to see you start this project. Did you ever build the Monogram Mirage 2000 and ESCI Jaguar I sold you? K/r, Dutch

Nathan Dempsey
Thanks Clifford & Desert!

Dutch: Same here. Still cutting downed trees and burning it all. Too much to place by the streets. The Mirage waits in the stash and the Jag was built as a close copy of my Kosovo build and given to a friend.

Nathan Dempsey
Added some photos of continuing work which includes more paint work on the landing gear and exhaust, the addition of the painted ejection seat to the cockpit & the completed external fuel tank.

Clifford Keesler
Beautiful work.

Desert Marlin
Looks great! I suppose you are aware that the Mirage 2000 series aircraft have the option of an arresting hook or a parachute for landing? I believe either can be installed but only one of the two depending on airfields and conditions. Referring to photo #5.

Nathan Dempsey
Thanks Clifford & thanks for the catch on that parachute housing Desert!

I found a good picture of a '91 Mirage 2000 with the bigger chaff dispenser replacing the back of that housing. I'll need to go back and file that off and change the position of all the chaff dispensers. I'll add some pictures this evening.

Laurent VILLANUEVA HELLER ForEver
je vais suivre = 2000 et daguet !

Laurent VILLANUEVA HELLER ForEver
color pit = humbrol 27
radome = 64 ,
grey 127
blue = 144 with white...

Guy Rump
Looking good, following. 👍

Nathan Dempsey
Welcome Laurent and thanks for the color info! Paint work is near.

Thanks Guy! 🙂

Desert Marlin
The chaff dispenser sits over the parachute housing and therefore the chute can still be used!

Clifford Keesler
Looking very nice Nathan.

Desert Marlin
I have had this one in my stash since 2008...

Nicolas
Following

yngvenett
I'm following this to learn

Martin Oostrom
Another tutorial one needs to watch

Gerald Sigmund
@mks: Komakais Walkaround shows meshes for the left and right intakes and none for the center one.

Bozzer
I have no idea of your subject, but I do enjoy your builds. The tutorial is always a lesson, and very informative. Keep them coming 👍

Pepe
Looking

berni
I take a seat 👍

DerMattes
Watching 👍

Johne 69
I am in too 😃

Ben M
When you thin parts, what technique do you use?

MS K
@Ben M - When I need to shave a lot, like this time, I use file.

Michael Kohl
Martin and Bozzer pointed it out. This will be fun and informative to follow.

Matteo Pescarin
Oh wow, as usual, fantastic documentation of the efforts going into this project. Chapeau to you!
Nonetheless, it makes me want to skip any Revell kit from now on... if I only didn't have any in my stash XD

MS K
@Matteo - The new mold products produced since around 2010 are generally nice quality(2CV, VW T1, 911G, Etc...) , but this product is so poorly made that it is ridiculous. I don't know what the production concept of this kit is. It is poor for a precision model, and it's not even easy to assemble.

Michael Kohl
With Revell you better check in advance how that specific kit is rated by others. They have tons of reboxes and quite a few kits where you just wanna ask: are you serious? But then, once in a while, just to show that they are able - in general - to be a serious modelling company, they release some really fine stuff. Doesn't hurt to be prepared what you're up against.

Alexander Grivonev
A true Revell car kit experience 👍 The casted on wiper is especially painful

Michael Kohl
That diffusor is a tremendous improvement.

amazon.com/dp/B00004..aps%2C163&sr=8-3
Such a tool makes such work as fitting the diffusor panels to the chassis much easier (the thinner the needles/pins, the more precise the contour).
Just a german site to give an idea.
Cheers Michael

MS K
Nice idea. I wish there was something made of insect pins thin enough to use in a plamodel.

Johne 69
Great work so far 👍

berni
A question. What Colours you would use at this kit?

MS K
@berni - The red is Italian Red, and I plan to use Cobalt Blue + Sky Blue (the instructions say to mix Ultramarine and Blue).

Denis Dogadov
I make up the silkscreen on the glass with a very thinly sliced masking tape.

[img1]
[img2]

MS K
@Denis - Yeah, I used to do it that way too, before I started using masking film.
My advice is that when masking that way, 'Tamiya masking tape for curves' is much easier than paper tape.
Youtube Video