Novità

Skyhiker
The order makes no sense going from a product to other related products and then back to comments of the original product. This is especially true because you need to read the comments to know what related products are needed.

Skyhiker
Having the comments at the bottom is confusing because you don't know if it is for the product or the thing just above the comments.

scalemates
Others share the same opinion?

Spanjaard
maybe a link on top to jump to comments would resolve the problem, without changing layout?

Michael Kohl
I actually had the same idea as Skyhiker and occasionally refrained from commenting on a kit as I thought that it will not be recognised. I think his suggestion is a good idea.

Martin Oostrom
You might want to get a cutting mat. It has saved me a couple of times when I spilled paint and glue. Keeps the table clean.

Kesa Tiho
I have a few thick pieces of paper under me stuff so i dont think anything is going through that

Spanjaard
you may be surprised with the effects of deflected sharp objects or spilled chemicals/paints..... specially since they tend to land just a centimeter away from the end of papers and half a millimetre deeper as well 😉

Michael Kohl
Ok, here are my two cents on that:

A cutting mat is very recommended indeed. Bigger areas can be well protected with a sheet of cardboard.
I would add a very good set of files. I personally like the Basic Tamiya file set a lot because it has a good bite, is easy to control and not overly expensive (Basic File Set (Smooth Double Cut) (Tamiya 74104, No)).
High quality nippers make a hell of a difference, but be warned: their price hurts. But as soon as you have them, you'll never regret it. Treat them with care and cut plastic only.
(Sharp Pointed Side Cutter for Plastic (Tamiya 74035, No))
Get one or two cheap brushes and two or three high quality ones. The first for mixing paints, the latter for your paint job. Sable is to be preferred, Winson & Newton Series No. 7 is a good bet, but there are many others around too. If your budget allows for only one (they are expensive!), I'd go for a size 2 brush. I do around 90% of my handpaint job with this size, but I do have an airbrush for larger areas. Smaller brushes hold only small quantities of paint and what you need to paint a detail is not a small brush, but a sharp tip of the brush. Again: treat them brushes nicely too.
Water alone doesn't clean your brushes thoroughly enough. Isopropyl alcohol helps with that, can be used to thin down the acrylic Tamiya paints and is way cheaper than special brush cleaners.

Get a set of sandpaper - preferably wet and dry. I like grit 400 for the coarser stuff, together with grit 280, 600, 800 and maybe 1500 will be a decent start. I still cherish the tip from Alexander Grivonev: get two erasers. One you cut into smaller pieces. When you wrap the sandpaper around the eraser you have a stable platform with a straight surface, but just the right amount of flexibility left. Of course you can buy sanding sticks too, which are very convenient, but they cost much, much more.
All told, this will cost you around 100€.
When equipped with this I would buy a second lamp (best with a so-called daylight bulb), to be placed on the other side of the working area to minimize shadows.
The ol' rule of other crafts apply to modelling too: you buy cheap, you buy twice.

I'd say, with the above mentioned stuff I still do about 80% of my basic modelling.

Hope this helps a bit.

Have fun. Cheers Michael

Kesa Tiho
Well i do have multiple lamps, i have a snipper at home and my mother builds stuff so i have an abundance of sand paper and other tools. But thanks for the suggestions Michael, they're well appreciated

Michael Kohl
That sounds good.
Concerning the nipper be aware that the ones for modelling have a special mode of cutting different from regular side cutters for cables i.e. With their mode of cutting almost no nub remains.