Novità

Sy Bar
Was going to do the Battle of Britain version of this kit but I'm temped to have a go at some winter white wash and the wasp is cooler than the shark mouth 😎

Nicolas
Following

István Szücs
I also have Bf-110 from the Airfix, I will build an Italian night fighter. The sprues are the same, so I'm watching!

Sy Bar
Cheers guys.
I'm have a go at riveting, but going freehand as at this scale using tape was taking so long. I also not sure how much they will stand out on finish kit, but with the wonky line in parts they will probably bee seen from mars 🤣

Mark Sherwood
Looking good so far, like the underside. 🥸👍

Sy Bar
Cheers #Mark

Skyhiker
Sy, how was the fit on this kit?

Guy Rump
Looking good, following. 👍

Sy Bar
Cheers #Guy 👍
#Skyhiker I found the fit to be good, I had a very slight gap at the front but think that was as much to do with me and the fitting of the pit (not the clearest instructions there). Every thing else was fine and the canopy was a good fit, I did change order of build slightly with the tail section I glued the rear piece to the body first then added the tail (after I'd added the stabilisers/rudders) this made more sense than the instructions 😁

Sy Bar
Only issue I have with this kit are the decals. While they look great and are in perfect register, they have a large amount of film edging and are both thick and delicate at the same time🤪
Having a hard time getting them to settle into the panel lines etc. I usually just need to use micro sol but even ultimate extra strong is not have much effect. Going to have to wait till I get some Tamiya fixer, strong and extra strong hopefully one of these will help 🤞

Mr D
You should be ok with the medium one with Airfix decals,
I like a mix of Water in with the markfix...seems to keep the decal floating longer.
I did the teeth on my p40 this way.
If they started getting bit sicky...l would add bit more water....keep it floating.
Wouldn't like to do shark teeth with HB decals 🤔🤣.... The lightning ⚡ strike on my mig-15 just fell apart with hardly any working.
Good luck with it ..look forward to seeing 😃👍👍

Dave Flitton
Looking good!

Sy Bar
Cheers for advice #Mr D. Afraid this set of decals were unaffected by all solutions but the mark fit super strong did have some effect. To make head way I found I needed to add the solution then after a few seconds apply hot air from a hairdryer to 'shrink wrap' the decal. These have to be the worst decals I've come across..
I recommend anyone doing this kit to source a set of decals rather than use those provided, they are not for beginners that's for sure. I hope the carrier film will disappear under a gloss coat but I didn't want to risk it so I've only applied the larger decals the smaller ones while add great detail if cartograf here they are 90% carrier film.

Skyhiker
Why don't you just cut the carrier film away with a knife before applying them?

Mr D
Hi Sy
That's ok .... I think the result will be fine after a clear coat, you come out of it without wrinkles, bubbles or tear's so it's a win, very smart n be sorted under a clear.👌👍👍

Sy Bar
Cheers #Mr D
#Skyhiker that's idea but life's too short for the amount there is, the size of the decal that's left will look like small black dots everywhere (especially the fuselage rib numbers 🤪); would be ok in 48 but too much in 72. Also I'm probably going to much it all up when I apply the winter white wash 😆

Rui S
That's Looking Great 👍

Jan Tichý
Hi, I´d like to buy this kit. I am from the Czech Republic. Paypal for payment. Is it available?
Best regards
Jan.

Andre Hoencher
Hi Jan, the Kit is available. The postalcosts with DHL is wihtout tracking 10,49€ and with tracking 14,49€ to Czech Republic. Paypal is ok, please send for Friends or Family.
Best regards André

Jan Tichý
Hi, Andre,
that sounds great. I think from Germany to Czechia is ok without tracking, so I´ll send you 23 Euro. Send me your PayPal, please.

Jan

Andre Hoencher
Hi Jan, my Paypal address: ak.hoencher@kabelmail.de
I still need your postal address and would send the package on Friday.
Best regards, Andre

Doubtingmango
Watching

Mr D
Thanks, Appreciate the interest, lm reality new to the hobby about 14 months, finding my way with techniques.
Weathering n panel lines need more learning.
The IAR-80 was decent price from HB and liked the paint scheme...bit different
👍👍

J35J
I'm in!

Mr D
Thanks J35.
Nice to have the interest, HB instructions bit weak!
They said to paint interior charcoal black like on the FW-190.
But l checked n the Romanian lAR interior was grey/blue.
Engine building next 6 parts deal.
Cheers 😃👍

Miguel Vaquero
Looking good mate. Following!!

Mr D
Good to have you along Miguel, engine n wings next,
A small amount of the wing is seen through bottom of cockpit, the HB instructions didn't mention painting it first!!
But the fit of the model be ok so far.
👍👍

Robert Podkoński
Joining the party!

Mr D
Thanks Robert, good to have you on board 👋😀👍

Miguel Vaquero
Love the idea of filling with acrylic, never thought about it. Does it hold well though time?

Mr D
Hi, Yes lve used it alot and holds up really well , l find the fillers a bit messy and more trouble than it's worth on small gaps.
You do need to allow overnight drying with it for best sanding results.
😀👍

Doubtingmango
Brilliant! The putty really can create a mess with finely molded details

NLAWScametovisit
This is extremely clever!!!

Mr D
Yes it has a habit of filling in panel lines n bits not necessary!!
This technique is same as using alot of paint to fill a gap or high build primer ect...just becomes part of the paint layer as it acrylic too.
But it's not for big gaps!! As there is a bit of shrinking overnight.
Be onto marking rivets next step after sanding... Then need to make choices on open or closed canopy???

Kesa Tiho
If anyone dare look away from that then every romanian within a 20 km radius will undo all your progress like a bunch of wolves eating a sheep

Landlubber Mike
Looking really good Mr D!

Mr D
Thanks Mike 👋😀👍.
Ive got the canopy on now, HB do nice clear glass, so I'm having a closed cockpit,
So bit of masking to do there next.
Ive got X2 builds on the go at min.
All the best 👍👍

Miguel Vaquero
I got to get myself a chrome pen. The result on those details look awesome

Mr D
Thanks Miguel, the pen needs a good shake prior to use , if it awkward area you can pump some out n use brush...but work fast.
Best to put a clear over next day as it's bit delicate.

Alexander Perov
Do not forget that the mast of the antenna passes through the windshield and is very clearly visible. This model may come in handy in my albums

Mr D
Ok thanks Alexander, HB didnt make the Mast installation very clear, the show it just glued on the top, will be very weak!! I've seen one build and it's come away!!
I'm going to use steel rod.
👍👍

Guy Rump
Following with interest! 👍

Mr D
Thanks Guy.... good to have you around 😃👍