Novità

Juergen Klinglhuber
Started this one.
The Ju 86 which were seen in 2 different Austrian markings, but at the end was never part of the Airforce. Here the overall silver Ju86 #311 at the airshow in Vienna-Aspern in early 1937.

Cuajete
Following 👍

Robert Podkoński
Interesting. Taking a seat here, of course!

Łukasz Gliński
Me 3 👍

Alec K
Me 4 🙂

Finn
I'm in

Dave Flitton
Watching!

Juergen Klinglhuber
Hello mates and thank you for your interest!

Juergen Klinglhuber
The mention aircraft was sent to the Airshow in Aspern as a "demonstrator" in austrian marking. Austria was interessed in buying 18 Ju86K-7. Due to several reasons Junkers was not prepared for that airshow and on short note removed the markings of an 86K-2 that was already prepared to be sold to Sweden. They put on austrian markings, a service number #311 and flew it over to Austria for just this one day. Flight captain Behrendt did a good job and the aerobatic air-display was a great success. So far so good. Why I am telling this? 86-K2 is a differend engine and cowling. The box is a 86E1/2. Aftermarket conversion products are out there (Kora) .....I had difficulties to locate/buy some.
Therefore: it is Scratchbuilding time again !!! 😎

Guy Rump
Following. 👍

Juergen Klinglhuber
Welcome Guy

Alec K
Nice progress. Modelimex is a place to get the Kora parts from, just in case 👍

Łukasz Gliński
There's one set here 😛
mojehobby.pl/product..I-Prewar-Bomber.html

Cuajete
Good explanation, Juergen 👍

Juergen Klinglhuber
thx Alec &Lukasz for you very kind support 👍 - appreciated.
But the first cuts are already done - no way back now 😉
(and I have to odmit: usually I like it to test my skills by a DIY task every now and then)

Bernd Grün
An Austrian Ju 86, I'm in! Nice start, Jürgen! 👍

Juergen Klinglhuber
Hi Bernd! thx

J35J
Great start! Watching with intrest.

Juergen Klinglhuber
Thank you and welcome J35J.

Stefan Fraundorfer
Ah, a new and very interesting project. Of course I will follow that. Have fun with the Ju 86 Jürgen.

Juergen Klinglhuber
Welcome aboard Stefan!

Juergen Klinglhuber
I have finished the modification on the engine resp. cowling. Some new pic's up-loaded.

Roland Sachsenhofer
Very interesting and extremely promising! We talked about it in Ried, and now I'm delighted to see these ideas being realised in such an impressive way!

Juergen Klinglhuber
🙏 Thx alot Roland, I am happy to receive your appreciation.

Nicolas
I'm joining this interesting build.

Łukasz Gliński
Impressive rework of the engines 👍

Alec K
I agree, looks very good 👍

TH SCALE MODELS (Thomas Haberl)
Nice progress Jürgen! I´m in to see how this beauty comes together 👍

Cuajete
Fantastic mods, 👌

Juergen Klinglhuber
Thank you mates for leaving your nice comments.Iam wWorking on the exhaust pipe currently. New picture up-date should be ready after this coming weekend.

TH SCALE MODELS (Thomas Haberl)
First "batch" of components ready for primer

Alec K
Cool! Very promising start, taking a seat 👍

TH SCALE MODELS (Thomas Haberl)
Welcome and thanks for your motivating words @Alec . First time I use something 3D printed and until now I enjoy it ☺️

Nicolas
Looks great so far.

Rui
I'm in 👍

DerMattes
Promising start, watching!

TH SCALE MODELS (Thomas Haberl)
Welcome @Nicolas, @ Rui and @DerMattes - thanks for your interest in this build 😊

TH SCALE MODELS (Thomas Haberl)
A small update here ... engine took my a while to get fitted in the fuselage. Didn´t work precisely enough so I got paid off when I tried to put the engine in. Anyway I solved it somehow without any major visible impact.

Skyhiker
Following

Rui
I gotta. say that I really appreciated there build posts that people share; its a real treat to see a bunch of plastic and such come together into a masterpiece! I learn so much from watchings.

TH SCALE MODELS (Thomas Haberl)
Welcome @Skyhiker - thanks for your interest on this build @Rui thanks for your kind words, even if I don´t think that anybody can learn much from my work .... but this is exactly what this stunning community is for ... I learned so much from people´s builds here ...

Neuling
How can you handle these tiny parts .... amazing

Alec K
Glad you solved the hurdle. Any ideas why the engine did not fit, or what the issue was?

Bruce Huxtable
1:72? I would have trouble with those tiny PE part of it were 1:32!! Well done on your precise work.

J35J
Great work Thomas!
Really impressed of your clean build and how you apply thiny amount of glue on all delicate small PE parts without creating a mess.

TH SCALE MODELS (Thomas Haberl)
thank you all for your kind words - I really appreciate that and this motivates me to constantly push myself out of the comfort zone .... thanks thanks thanks!!!! @Neuling: I know your skills so I´m really glad you came around my build: the answer is patience and a glass of good wine 😆 @Alec: as you can see the engine comes in a lot of tine parts and I didn´t pay enough attention when removing the print support and grinding the parts down properly. This resulted in a too long engine assembly. Lucky my I always spend a lot of time on dry-fits so I recognized it before starting to glue it in. Almost complete front end is made of printed parts and slightest deviations result that engine cowlings won´t fit together. Not a must to have them completely align when you show them open but I want to paint the all in one and then open the cowlings once done ...

Neuling
Thomas, will a glass of beer do ? 🙂

TH SCALE MODELS (Thomas Haberl)
@Neuling … who drinks beer in glasses? 😂 but I guess it will work

Neuling
🙂

Alec K
Thanks Thomas 👍. Ehm, I need glasses to find the beer… 😄

Trez Mackenzie
What was the cause of engine fitting? I have just got the engine pack. Any advice?

Ah, I read your previous post. It seems that most folk seem to buy these things as an aesthetic object so hats off for taking this on!

TH SCALE MODELS (Thomas Haberl)
@Trez: as you may have seen in previous comments, the most important thing is to really carefully sand all components down. Tend to say do a little more. There are many components coming together (assembled engine itself, manually modified fuselage, printed cowlings, ... ) and should fit properly in the end to avoid any gaps or twists in the final assembly. I think it would be tricky even in bigger scale. 1/72 scale has no mercy in this complex assembly of the plane front end. I managed it, but didn´t upload any pictures here so stay tuned 😊

Sergej I
Following! 👍, great job with cockpit and engine so far.
I have the exact same setup for an F-8 Würger in the shelf 🙂

Trez Mackenzie
Thanks Thomas, I look forward to the fots

TH SCALE MODELS (Thomas Haberl)
@Trez: I will share some when I´m back - currently traveling and far away from my bench. @Sergej: thanks for your positive feedback, I hope my experiences on this build help to make yours a little bit more straight forward 😆

TH SCALE MODELS (Thomas Haberl)
After a longer break on this I was finally able to restart on this build. Main engine components placed in fuselage, rivets added (as much as possible on this scale) and hydraulic tubes adde to landing gear. Now a bit of tedious work ... sanding and preparation for primer. Not much but in tricky places.

Frank Brzobohaty
Great job, not the easiest in 1:72 scale is it Thomas? but it is rewarding when completed!

TH SCALE MODELS (Thomas Haberl)
Thanks @Frank!! Indeed it was a challange, especially when working with these resin parts for the first time. But as you say, I hope it will be rewarding once the Würger is done 🤷‍♂️

Juergen Klinglhuber
Looking good - realy looking forward to see the finished bird.